An Integral Battery Charger with Power Factor Correction for Electric Scooter

This paper presents an integral battery charger for an electric scooter with high voltage batteries and interior-permanent-magnet motor traction drive. The battery charger is derived from the power hardware of the scooter, with the ac motor drive that operates as three-phase boost rectifier with power factor correction capability. The control of the charger is also integrated into the scooter control firmware that is implemented on a fixed-point DSP controller. Current-controlled or voltage-controlled charge modes are actuated according to the requirements of the battery management system, that is embedded into the battery pack. With respect to previous integrated chargers, the ac current is absorbed at unitary power factor with no harmonic distortion. Moreover, no additional filtering is needed since the pulsewidth modulation ripple is minimized by means of phase interleaving. The feasibility of the integral charger with different ac motors (induction motor, surface-mounted phase modulation motor) is also discussed, by means of a general model purposely developed for three-phase ac machines. The effectiveness of the proposed battery charger is experimentally demonstrated on a prototype electric scooter, equipped with two Li-ion battery packs rated 260 V, 20 A

Cancellation Predictive Control for Three-Phase PWM Rectifiers under Harmonic and Unbalanced Input Conditions

This paper presents an intuitive and simple-to-implement control scheme to improve the performance of three-phase boost-type PWM rectifiers under harmonic and unbalanced input conditions. Unlike most other control strategies, the proposed method does not need to extract either the harmonic or the negative-sequence components in the supply voltages and currents. A near-synchronous reference frame is used to determine the positive-sequence fundamental-frequency component in the input voltages. Utilizing only the extracted component, the DC-link voltage control and power factor control are implemented independently to determine the phase angle and magnitude of the PWM reference voltage. The commanded rectifier voltage adjustments are superimposed upon the grid voltages in such a way that the distortions (both harmonic and negative sequence components) are effectively cancelled. By employing a near-synchronous reference frame, no line-synchronization algorithm or hardware PLL is needed, so very little computational effort is required for its implementation. Simulation results show that the proposed method performs very well under extreme harmonic and unbalanced conditions such as when one or even two phases of the grid voltages are zero. In order to further verify its effectiveness, a laboratory hardware platform has been develope

A Novel Control Method For Grid Side Inverters Under Generalized Unbalanced Operating Conditions

This thesis provides a summary on renewable energy sources integration into the grid, using an inverter, along with a comprehensive literature research on variety of available control methods. A new generalized method for grid side inverter control under unbalanced operating conditions is also proposed. The presented control method provides complete harmonic elimination in line currents and DC link voltage with adjustable power factor. The method is general, and can be used for all levels of imbalance in grid voltages and line impedances. The control algorithm proposed in this work has been implemented by using MATLAB Simulink and dSPACE RT1104 control system. Simulation and experimental results presented in this thesis are in excellent agreement

Design and Control of Power Converters for High Power-Quality Interface with Utility and Aviation Grids

Power electronics as a subject integrating power devices, electric and electronic circuits, control, and thermal and mechanic design, requires not only knowledge and engineering insight for each subarea, but also understanding of interface issues when incorporating these different areas into high performance converter design.Addressing these fundamental questions, the dissertation studies design and control issues in three types of power converters applied in low-frequency high-power transmission, medium-frequency converter emulated grid, and high-frequency high-density aviation grid, respectively, with the focus on discovering, understanding, and mitigating interface issues to improve power quality and converter performance, and to reduce the noise emission.For hybrid ac/dc power transmission,• Analyze the interface transformer saturation issue between ac and dc power flow under line unbalances.• Proposed both passive transformer design and active hybrid-line-impedance-conditioner to suppress this issue.For transmission line emulator,• Propose general transmission line emulation schemes with extension capability.• Analyze and actively suppress the effects of sensing/sampling bias and PWM ripple on emulation considering interfaced grid impedance.• Analyze the stability issue caused by interaction of the emulator and its interfaced impedance. A criterion that determines the stability and impedance boundary of the emulator is proposed.For aircraft battery charger,• Investigate architectures for dual-input and dual-output battery charger, and a three-level integrated topology using GaN devices is proposed to achieve high density.• Identify and analyze the mechanisms and impacts of high switching frequency, di/dt, dv/dt on sensing and power quality control; mitigate solutions are proposed.• Model and compensate the distortion due to charging transition of device junction capacitances in three-level converters.• Find the previously overlooked device junction capacitance of the nonactive devices in three-level converters, and analyze the impacts on switching loss, device stress, and current distortion. A loss calculation method is proposed using the data from the conventional double pulse tester.• Establish fundamental knowledge on performance degradation of EMI filters. The impacts and mechanisms of both inductive and capacitive coupling on different filter structures are understood. Characterization methodology including measuring, modeling, and prediction of filter insertion loss is proposed. Mitigation solutions are proposed to reduce inter-component coupling and self-parasitics

Analysis, Design and Control of a Modular Full-Si Converter Concept for Electric Vehicle Ultra-Fast Charging

L'abstract è presente nell'allegato / the abstract is in the attachmen

New techniques to improve power quality and evaluate stability in modern all-electric naval ship power systems

This dissertation focuses on two crucial issues in the design and analysis of the power electronic systems on modern all-electric naval ships, i.e., power quality control and stability evaluation. It includes three papers that deal with active power filter topology, active rectifier control, and impedance measurement techniques, respectively. To mitigate harmonic currents generated by high-power high-voltage shipboard loads such as propulsion motor drives, the first paper proposes a novel seven-level shunt active power filter topology, which utilizes tapped reactors for parallel operations of switching devices. The multi-level system has been implemented in both regular digital simulation and real-time digital simulator for validation. In the second paper, a harmonic compensation algorithm for three-phase active rectifiers is proposed. Based on the theory of multiple reference frames, it provides fast and accurate regulation of selected harmonic currents so that the rectifier draws balanced and sinusoidal currents from the source, even when the input voltages are unbalanced and contain harmonics. Extensive laboratory tests on a 2 kW prototype system verifies the effectiveness of the proposed control scheme. The last paper presents a new technique for impedance identification of dc and ac power electronic systems, which significantly simplifies the procedure for stability analysis. Recurrent neural networks are used to build dynamic models of the system based on a few signal injections, then the impedance information can be extracted using off-line training and identification algorithms. Both digital simulation and hardware tests were used to validate the technique --Abstract, page iv

Flexible operation of grid-interfacing converters in distribution networks : bottom-up solutions to voltage quality enhancement

Due to the emerging application of distributed generation (DG), large numbers of DG systems are expected to deliver electricity into the distribution network in the near future. For the most part these systems are not ready for riding through grid disturbances and cannot mitigate unwanted influences on the grid. On the one hand, with the increasing use of sensitive and critical equipment by customers, the electricity network is required to serve high voltage quality. On the other hand, more and more unbalanced and nonlinear equipment, including DG units, is negatively affecting the power quality of distribution networks. To adapt to the future distribution network, the tendency for grid-interfacing converters will be to integrate voltage quality enhancement with DG functionality. In this thesis, the flexible operation of grid-interfacing converters in distribution networks is investigated for the purpose of voltage quality enhancement at both the grid and user sides. The research is carried out in a bottom-up fashion, from the low-level power electronics control, through the realization of individual system functionality, finally arriving at system-level concepts and implementation. Being essential to the control of grid-interfacing converters, both stationaryframe techniques for voltage detection and synchronization in disturbed grids, and asymmetrical current regulation are investigated. Firstly, a group of high performance filters for the detection of fundamental symmetrical sequences and harmonics under various grid conditions is proposed. The robustness of the proposed filters to small grid-frequency variation and their adaptability to large frequency change are discussed. Secondly, multiple reference frame current regulation is explored for dealing with unbalanced grid conditions. As a complement to the existing proportional resonant (PR) controllers, sequence-decoupled resonant (SDR) controllers are proposed for regulating individual symmetric sequences. Based on the modeling of a four-leg grid-connected system in different reference frames, three types of controllers, i.e. PI, PR, and proportional plus SDR controllers are compared. Grid-interactive control of distributed power generation, i.e. voltage unbalance compensation, grid-fault ride-through control and flexible power transfer, as well as the modeling of harmonic interaction, are all investigated. The in-depth study and analysis of these grid interactions show the grid-support possibilities and potential negative impact on the grid of inverter-based DG units, beyond their primary goal of power delivery. In order to achieve a co-operative voltage unbalance compensation based on distributed DG systems, two control schemes, namely voltage unbalance factor based control and negative-sequence admittance control, are proposed. The negativesequence voltages at the grid connection point can be compensated and mitigated by regulating the negative-sequence currents flowing between the grid and DG converters. Flexible active and reactive power control during unbalanced voltage dips is proposed that enables DG systems to enhance grid-fault ride-through capability and to adapt to various requirements for grid voltage support. By changing adaptable weighting factors, the compensation of oscillating power and the regulation of grid currents can be easily implemented. Two joint strategies for the simultaneous control of active and reactive power are derived, which maintain the adaptive controllability that can cope with multiple constraints in practical applications. The contribution of zero-sequence currents to active power control is also analyzed as a complement to the proposed control, which is based on positive- and negative-sequence components. Harmonic interaction between DG inverters and the grid is modeled and analyzed with an impedance-based approach. In order to mitigate the harmonic distortion in a polluted grid, it is proposed to specify output impedance limits as a design constraint for DG inverters. Results obtained from modeling, analysis, and simulations of a distribution network with aggregated DG inverters, show that the proposed method is a simple and effective way for estimating harmonic quasi-resonance problems. By integrating these proposed control strategies in a modified conventional series-parallel structure, we arrived at a group of grid-interfacing system topologies that is suitable for DG applications, voltage quality improvement, and flexible power transfer. A concrete laboratory system details the proposed concepts and specifies the practical problems related to control design. The introduction of multi-level control objectives illustrates that the proposed system can ride through voltage disturbances, can enhance the grid locally, and can continue the power transfer to and from the grid while high voltage quality is maintained for the local loads within the system module. A dual-converter laboratory set-up was built, with which the proposed concepts and practical implementation have been fully demonstrated

Power Quality

Electrical power is becoming one of the most dominant factors in our society. Power generation, transmission, distribution and usage are undergoing signifi cant changes that will aff ect the electrical quality and performance needs of our 21st century industry. One major aspect of electrical power is its quality and stability – or so called Power Quality. The view on Power Quality did change over the past few years. It seems that Power Quality is becoming a more important term in the academic world dealing with electrical power, and it is becoming more visible in all areas of commerce and industry, because of the ever increasing industry automation using sensitive electrical equipment on one hand and due to the dramatic change of our global electrical infrastructure on the other. For the past century, grid stability was maintained with a limited amount of major generators that have a large amount of rotational inertia. And the rate of change of phase angle is slow. Unfortunately, this does not work anymore with renewable energy sources adding their share to the grid like wind turbines or PV modules. Although the basic idea to use renewable energies is great and will be our path into the next century, it comes with a curse for the power grid as power fl ow stability will suff er. It is not only the source side that is about to change. We have also seen signifi cant changes on the load side as well. Industry is using machines and electrical products such as AC drives or PLCs that are sensitive to the slightest change of power quality, and we at home use more and more electrical products with switching power supplies or starting to plug in our electric cars to charge batt eries. In addition, many of us have begun installing our own distributed generation systems on our rooft ops using the latest solar panels. So we did look for a way to address this severe impact on our distribution network. To match supply and demand, we are about to create a new, intelligent and self-healing electric power infrastructure. The Smart Grid. The basic idea is to maintain the necessary balance between generators and loads on a grid. In other words, to make sure we have a good grid balance at all times. But the key question that you should ask yourself is: Does it also improve Power Quality? Probably not! Further on, the way how Power Quality is measured is going to be changed. Traditionally, each country had its own Power Quality standards and defi ned its own power quality instrument requirements. But more and more international harmonization efforts can be seen. Such as IEC 61000-4-30, which is an excellent standard that ensures that all compliant power quality instruments, regardless of manufacturer, will produce of measurement instruments so that they can also be used in volume applications and even directly embedded into sensitive loads. But work still has to be done. We still use Power Quality standards that have been writt en decades ago and don’t match today’s technology any more, such as fl icker standards that use parameters that have been defi ned by the behavior of 60-watt incandescent light bulbs, which are becoming extinct. Almost all experts are in agreement - although we will see an improvement in metering and control of the power fl ow, Power Quality will suff er. This book will give an overview of how power quality might impact our lives today and tomorrow, introduce new ways to monitor power quality and inform us about interesting possibilities to mitigate power quality problems. Regardless of any enhancements of the power grid, “Power Quality is just compatibility” like my good old friend and teacher Alex McEachern used to say. Power Quality will always remain an economic compromise between supply and load. The power available on the grid must be suffi ciently clean for the loads to operate correctly, and the loads must be suffi ciently strong to tolerate normal disturbances on the grid

Power factor-corrected transformerless three-phase PWM converter for UPS applications

This thesis describes the research of a new transformerless three phase PWM converter for uninterruptible power supplies (UPS) applications. The removal of the bulky three phase transformer in larger power UPS can provide a significant saving in weight and cost of the overall system. The converter consists of a new four-wire rectifier coupled with a four-wire inverter via a dc bus. The supply and load neutral may be connected together without any neutral current flowing into the utility regardless of the load on the inverter. This allows the load to be at the same potential as the utility. The rectifier, inverter and complete UPS and control system are described in detail and simulation results are used extensively to back up the theory. An experimental prototype of the four-wire rectifier provides further confirmation of the principles. A further proposal to digitize the system is given. This would reduce the size of the required control circuit and simplify the hardware requirements

Contributions to cascade linear control strategies applied to grid-connected Voltage-Source Converters

El trabajo desarrollado en esta Tesis se centra en optimizar el comportamiento de Voltage-Source Converters (VSCs) cuando son utilizados como interfaz con la red eléctrica, tanto para absorber como para entregar energía de la red con la mejor calidad posible y cumpliendo con los estándares. Para tal fin, esta Tesis se centra en el control de sistemas lineales conectados en cascada aplicados al control de VSCs conectados en paralelo con la red eléctrica a través de un filtro L, especialmente en conexiones con redes débiles y en dos líneas de trabajo: (i) seguimiento de armónicos de las corrientes de red y rechazo de armónicos de las tensiones de red, y (ii) control de la tensión del PCC en caso de desequilibrio. Para ello, esta Tesis realiza contribuciones en el área del control de corriente y control de la tensión del PCC. De entre las técnicas existentes para implementar el control de corriente para compensación armónica, dos de las más utilizadas son el control resonante y el control repetitivo, tanto en ejes de referencia estacionarios como síncronos. Se ha realizado un exhaustivo estudio de diferentes estructuras para implementar tales controles, mostrando su algoritmo adaptativo en frecuencia para cada una de ellas y analizando su carga computacional. Además, se han facilitado directrices básicas para su programación en un DSP. Se ha analizado también el esquema de control de corriente para establecer una comparación entre las diferentes estructuras. Después de estudiar en profundidad el control de corriente de un VSC conectado a la red eléctrica, el segundo control a analizar es el control de tensión del PCC. La presencia de una tensión desequilibrada en el PCC da lugar a la aparición de una componente de corriente de secuencia negativa, que deteriora el comportamiento del sistema de control cuando se emplean las técnicas de control convencionales. Los STATCOMs son bien conocidos por ser una aplicación de potencia capaz de llevar a cabo la regulación de la tensión en el PCC en líneas de distribución que pueden ser susceptibles de sufrir perturbaciones. Esta Tesis propone el uso de un controlador de tensión en ejes de referencia síncronos para compensar una tensión desequilibrada a través de un STATCOM, permitiendo controlar independientemente tanto la secuencia positiva como la secuencia negativa. Además, este controlador incluye aspectos como un mecanismo de antiwindup y droop control para mejorar su comportamiento. Se han realizado varias pruebas experimentales para analizar las características de los controladores de corriente abordados en esta Tesis. Todas ellas han sido realizadas bajo las mismas condiciones de potencia, tensión y corriente, de modo que se pueden extraer resultados comparativos. Estas pruebas pretenden caracterizar la respuesta transitoria, la respuesta en régimen permanente, el comportamiento frente a saltos de frecuencia y la carga computacional de los controladores de corriente estudiados