Design and Optimization of a 3-D Plasmonic Huygens Metasurface for Highly-Efficient Flat Optics

For miniaturization of future USAF unmanned aerial and space systems to become feasible, accompanying sensor components of these systems must also be reduced in size, weight and power (SWaP). Metasurfaces can act as planar equivalents to bulk optics, and thus possess a high potential to meet these low-SWaP requirements. However, functional efficiencies of plasmonic metasurface architectures have been too low for practical application in the infrared (IR) regime. Huygens-like forward-scattering inclusions may provide a solution to this deficiency, but there is no academic consensus on an optimal plasmonic architecture for obtaining efficient phase control at high frequencies. This dissertation asks the question: what are the ideal topologies for generating Huygens-like metasurface building blocks across a full 2π phase space? Instead of employing any a priori assumption of fundamental scattering topologies, a genetic algorithm (GA) routine was developed to optimize a “blank slate” grid of binary voxels inside a 3D cavity, evolving the voxel bits until a near-globally optimal transmittance (T) was attained at a targeted phase. All resulting designs produced a normalized T≥80 across the entire 2π range, which is the highest metasurface efficiency reported to-date for a plasmonic solution in the IR regime

Directional speech acquisition using a MEMS cubic acoustical sensor microarray cluster.

This thesis presents the design of a directional speech acquisition system using a MEMS cubic acoustical sensor microarray cluster to improve speech intelligibility in a noisy reverberant acoustical environment. In the proposed system, five identical acoustical sensor arrays constitute the five sides of a cubic geometry whereas the other side of the cube is to be used for interconnection and packaging purposes. Each of the sensor microarrays is associated with two beam shapes: a main beam to acquire speech signal from a particular direction and a scanning beam to locate and track a potential speech source. A microelectronics based beam synthesis engine controls the selection of a main beam to acquire speech signals from a particular direction based on the output level of the five scanning beams. In this way the developed system provides an improved reduced noise dynamic directional speech acquisition system covering a 3-D space. (Abstract shortened by UMI.)Dept. of Electrical and Computer Engineering. Paper copy at Leddy Library: Theses & Major Papers - Basement, West Bldg. / Call Number: Thesis2006 .H8. Source: Masters Abstracts International, Volume: 45-01, page: 0411. Thesis (M.A.Sc.)--University of Windsor (Canada), 2006

Effect of localization error on the performance of location-aided beam-management in 5G and beyond

openLe onde millimetriche sono ritenute essere la prossima frontiera per la trasmissione dei dati nelle moderne reti cellulari 5G e oltre. Tali onde però si attenuano più facilmente durante la propagazione e vengono rapidamente bloccate da ostacoli. E' necessario quindi un'operazione di beamforming, utilizzando per la trasmissione un array di antenne anziché una singola antenna. Con il beamforming è anche necessaria una procedura di ricerca tra trasmettitore e ricevitore, tale procedura è inefficiente nelle reti odierne e provoca ritardi nella trasmissione. E' possibile però sfruttare informazioni esterne per velocizzare l'allineamento, ad esempio, il ricevitore può fornire la propria posizione tramite GPS al trasmettitore cosicché quest'ultimo sappia dove indirizzare la successiva trasmissione dati. L'informazione ausiliaria in questione è però inevitabilmente soggetta ad errore che, a seconda del suo impatto, può addirittura impedire la comunicazione. Nel presente lavoro di tesi sono presentati diversi modelli di errore in scenari realistici, sono inoltre effettuate simulazioni per comprendere l'impatto che ha l'errore dell'informazione ausiliaria nell'intera procedura di beamforming.Millimeter waves are considered to be the next frontier for data transmission in modern 5G and beyond cellular networks. However, these waves attenuate more easily during propagation and are quickly blocked by obstacles. Therefore, a beamforming operation is necessary, using an array of antennas for transmission instead of a single antenna. Beamforming also requires a search procedure between the transmitter and receiver, which is inefficient in current networks and causes delays in transmission. However, external information can be leveraged to speed up the alignment process. For example, the receiver can provide its position via GPS to the transmitter, enabling the latter to know where to direct the next data transmission. Nevertheless, the auxiliary information is inevitably subject to error, which, depending on its impact, can even impede communication. This thesis presents various error models in realistic scenarios and conducts simulations to understand the impact of auxiliary information errors on the entire beamforming procedure

Adaptive Link Optimization for 802.11 UAV Uplink Using A Reconfigurable Antenna

This thesis presents a low-cost and flexible experimental testbed for aerial communication research along with an implementation and experimental evaluation of an aerial-to-ground 802.11g link with an adaptive beamsteering antenna system. The system consists of a software-defined radio (SDR) platform, and a pattern reconfigurable antenna mounted on a hexacopter unmanned aerial vehicle (UAV). First, the system design aspects of the testbed are described. The performance of the reconfigurable antenna is characterized through radiation pattern measurements while the antenna is mounted on the underbelly of the UAV. A low complexity reinforcement learning based adaptive antenna selection algorithm is implemented on the aerial SDR testing platform to enhance the link quality. We present SNR measurements obtained during various indoor and outdoor flight scenarios. The results show that utilizing a reconfigurable antenna and intelligent antenna selection strategy onboard a UAV provides a higher mean SNR compared to an omni-directional antenna in both line of sight (LOS) and non-line of sight (NLOS) scenarios, and is more resilient to co-channel interference and reactive jamming.M.S., Electrical Engineering -- Drexel University, 201

The Telecommunications and Data Acquisition Report

This publication, one of a series formerly titled The Deep Space Network Progress Report, documents DSN progress in flight project support, tracking and data acquisition research and technology, network engineering, hardware and software implementation, and operations. In addition, developments in Earth-based radio technology as applied to geodynamics, astrophysics and the radio search for extraterrestrial intelligence are reported

Radiation pattern reconfigurable microfabricated planar millimeter-wave antennas

Els serveis de telecomunicacions i sistemes radar estan migrant a freqüències mil•limètriques (MMW), on es disposa d 'una major amplada de banda i conseqüentment d'una major velocitat de transmissió de dades. Aquesta migració requereix de l'ús de diferents tecnologies amb capacitat d'operar a la banda de freqüències mil•limètriques (30 a 300 Ghz), i més concretament en les bandes Ka (26,5 - 40GHz), V (50 – 75GHz) i W (75 – 110GHz). En moltes aplicacions i sobretot en aquelles on l'antena forma part d'un dispositiu mòbil, es cerca poder utilitzar antenes planes, caracteritzades per tenir unes dimensions reduïdes i un baix cost de fabricació. El conjunt de requeriments es pot resumir en obtenir una antena amb capacitat de reconfigurabilitat i amb un baix nivell de pèrdues en cada una de les bandes de freqüència. Per tal d'afrontar aquests reptes, les dimensions de les antenes mil•limètriques, juntament amb els tipus de materials, toleràncies de fabricació i la capacitat de reconfigurabilitat ens porten a l'ús de processos de microfabricació. L'objectiu d'aquesta tesis doctoral és l'anàlisi dels conceptes mencionats, tipus de materials, geometries de línia de transmissió i interruptors, en el context de les freqüències mil•limètriques, així com la seva aplicació final en dissenys d'antenes compatibles amb els processos de microfabricació. Finalment, com a demostració s'han presentat dissenys específics utilitzables en tres aplicacions a freqüències mil•limètriques: Sistemes de Comunicació per Satèl•lit (SCS) a la banda Ka, Xarxes d'àrea personal inalàmbriques (WPAN) a la banda V i sistemes radar per l'automoció a la banda W. La primera part d'aquesta tesis consisteix en l'anàlisi d'algunes tecnologies circuitals a freqüències mil•limètriques. S'han presentat els materials més utilitzats a altes freqüències (Polytetrafluoroethylene or Teflon (PTFE), Quartz, Benzocyclobuten polymer (BCB) i Low Temperature Co-fired Ceramic (LTCC)) i s'han comparat en termes de permitivitat i tangent de pèrdues. També s'inclou un estudi de pèrdues a altes freqüències en les principals línies de transmissió (microstrip, stripline i CPW). Finalment, es presenta un resum dels interruptors RF-MEMS i es comparen amb els PIN diodes i els FET. En la segona part, es presenten diferents agrupacions d'antenes amb la capacitat de reconfigurar la polarització i la direcció d'apuntament. S'han dissenyat dos elements base reconfigurables en polarització: CPW Patch antena i 4-Qdime antena. La primera antena consisteix en un element singular amb interruptors RF-MEMS, dissenyada per operar a les bandes Ka i V. La segona antena consisteix en una arquitectura composta on la reconfigurabilitat en polarització s'obté mitjançant variant la fase d'alimentació de cada un dels quatre elements lineals. La fase és controlada mitjançant interruptors RF-MEMS ubicats en la xarxa de distribució. L'antena 4-Qdime s'ha dissenyat per operar en les bandes V i W. Ambdós elements base s'han utilitzat posteriorment pel disseny de dues agrupacions d'antenes amb capacitat de reconfigurar l'apuntament del feix principal. La reconfigurabilitat es dur a terme utilitzant desfasadors de fase d'1 bit. La part final de la tesis es centra en les toleràncies de fabricació i en els processo de microfabricació d'agrupacions d'antenes mil•limètriques. Les toleràncies de fabricació s'han estudiat en funció dels error d'amplitud i fase en cada element de l'agrupació, fixant-se en les pèrdues de guany, error d'apuntament, error en l'amplada de feix, errors en el nivell de lòbul secundari i en l'error en la relació axial. El procés de microfabricació de les diferents antenes dissenyades es presenta en detall. Els dissenys de l'antena CPW Patch reconfigurable en polarització i apuntament operant a les bandes Ka i V, s'han fabricat en la sala blanca del Cornell NanoScale Science & Technology Facility (CNF). Posteriorment, s'han caracteritzat l'aïllament i el temps de resposta dels interruptors RF-MEMS, i finalment, el coeficient de reflexió, el diagrama de radiació i la relació axial s'han mesurat a les bandes Ka i V per les antenes configurades en polarització lineal (LP) i circular (CP).Telecommunication services and radar systems are migrating to Millimeter-wave (MMW) frequencies, where wider bandwidths are available. Such migration requires the use of different technologies with the capability to operate at the MMW frequency band (30 to 300GHz), and more specifically at Ka- (26.5 to 40GHz), V- (50 to 75GHz) and W-band (75 to 110GHz). For many applications and more concretely those where the antenna is part of a mobile device, it is targeted the use of planar antennas for their low profile and low fabrication cost. A wide variety of requirements is translated into a reconfiguration capability and low losses within each application frequency bandwidth. To deal with the mentioned challenges, the MMW antenna dimensions, together with the materials, fabrication tolerances and reconfigurability capability lead to microfabrication processes. The aim of this thesis is the analysis of the mentioned concepts, materials, transmission lines geometries and switches in the MMW frequencies context and their final application in antenna designs compatible with microfabrication. Finally, specific designs are presented as a demonstration for three MMW applications: Satellite Communication Systems (SCS) at Ka-band, Wireless Personal Area Network (WPAN) at V-band and Automotive Radar at W-band. The first part of this thesis consist to analyze some MMW circuit technologies. The four most used materials at MMW frequencies (Polytetrafluoroethylene or Teflon (PTFE), Quartz, Benzocyclobuten polymer (BCB) and Low Temperature Co-fired Ceramic (LTCC)) have been presented and compared in terms of permittivity (εr) and loss tangent (tanδ). An study of the main transmission lines attenuation (microstrip, stripline and CPW) at high frequencies is included. Finally, an overview of the RF-MEMS switches is presented in comparison with PIN diodes and FETS switches. The second part presents different polarization and beam pointing reconfigurable array antennas. Two polarization-reconfigurable base-elements have been designed: CPW Patch antenna and 4-Qdime antenna. The first consists of a single reconfigurable element with integrated RF-MEMS switches, designed to operate at Ka- and V-band. The second antenna presented in this thesis has a composed architecture where the polarization reconfigurability is obtained by switching the phase feeding for each of the four linear polarized elements in the feed network with RF-MEMS switches. The 4-Qdime antenna has been designed to operate at V- and W-band. The two base-elements have been used to design two beam pointing reconfigurable antenna arrays. Using phased array techniques, beamsteering is computed and implemented with 1-bit discrete phase-shifter. The final part of the thesis is focused into the fabrication tolerances and microfabrication process of Millimeter-wave antenna arrays. The fabrication tolerances have been studied as a function of the amplitude and phase errors presented at each elements array, focusing on the gain loss, beam pointing error, Half-Power Beamwidth (HPBW) error, sidelobe level error and axial ratio error. The microfabrication process for the designed antennas is presented in detail. Polarization- and pointing- reconfigurable CPW Patch antenna operating at Ka- and V- band have been fabricated in a clean-room facility at Cornell NanoScale Science & Technology Facility (CNF). The RF-MEMS switches isolation and time response have been characterized. Finally, the reflection coefficient, radiation pattern and axial ratio have been measured at Ka- and V-band for the fabricated antennas configured in Linear Polarization (LP) and Circular Polarization (CP)

Large Eddy Simulation Of Surface Pressure Fluctuations Generated By Elevated Gusts

Wind gusts cause substantial damage to wind turbines. If these damaging winds could be detected prior to their interaction with the turbine, the turbine rotor can be decoupled from the generator and gearing system to prevent damage during the gust event. This would significantly reduce wind turbine repair costs. Wind gusts can also create unsafe conditions for aircraft landing. A ground based detection system that monitored elevated wind gusts can provide new information for pilots to use when determining whether or not it is safe to land. In addition, the ability to monitor elevated gust events would provide a new probe to study features in the atmospheric boundary layer. Previous research indicates that elevated velocity events, such as gusts, may trigger pressure fluctuations on the ground. If that is true, it should be possible to monitor elevated wind gusts by measuring these pressure fluctuations. The goal of this project is to develop a ground based detector that monitors the behavior of pressure fluctuations on the ground for indicators that a gust event may be taking place at higher altitudes. In order to recognize these indicators from the pressure measurements on the ground, cross-correlation analysis between the time evolution of the frequency structures corresponding to elevated wind gusts and the pressure on the ground below were investigated. The data for these analysis was generated using a large eddy simulation. This numerical approach was chosen because the nature of the cross-correlation analysis demanded full field wind velocities and pressures at several altitudes. Collecting this data outdoors would be impractical. Correlation coefficients between 0.75 - 0.90 were found. These high correlations indicate that the two signals are causally related. Several comfeatures of the pressures caused by elevated gusts were identified. These features were used to develop a tracking program that monitors fast moving high amplitude pressure fluctuations and to design a ground based pressure sensing array. The array design and tracking software was used to identify several new gust events within the simulated atmosphere. In total, eight gust events have been identified. These events show that the group velocities of the pressure fluctuations measured on the ground increase with the altitude location of the corresponding wind gust source. The methods, tracking software, and array design are ready to be used for experimental research outdoors

Analysis and performance improvement of consumer-grade millimeter wave wireless networks

Millimeter-wave (mmWave) networks are one of the main key components in next cellular and WLANs (Wireless Local Area Networks). mmWave networks are capable of providing multi gigabit-per-second rates with very directional low-interference and high spatial reuse links. In 2013, the first 60 GHz wireless solution for WLAN appeared in the market. These were wireless docking stations under theWiGig protocol. Today, in 2019, 60 GHz communications have gained importance with the IEEE 802.11ad amendment with different products on the market, including routers, laptops and wireless Ethernet solutions. More importantly, mmWave networks are going to be used in next generation cellular networks, where smartphones will be using the 28 GHz band. For backbone links, 60 GHz communications have been proposed due to its higher directionality and unlicensed use. This thesis fits in this frame of constant development of themmWave bands to meet the needs of latency and throughput that will be necessary to support future communications. In this thesis, we first characterize the cost-effective design of COTS (commercial off-the-shelf) 60 GHz devices and later we improve their two main weaknesses, which are their low link distance and their non-ideal spatial reuse. It is critical to take into consideration the cost-effective design of COTS devices when designing networking mechanisms. This is why in this thesis we do the first-of-its-kind COTS analysis of 60 GHz devices, studying the D5000 WiGig Docking station and the TP-Link Talon IEEE 802.11ad router. We include static measurements such as the synthesized beam patterns of these devices or an analysis of the area-wide coverage that these devices can fulfill. We perform a spatial reuse analysis and study the performance of these devices under user mobility, showing how robust the link can be under user movement. We also study the feasibility of having flying mmWave links. We mount a 60 GHz COTS device into a drone and perform different measurement campaigns. In this first analysis, we see that these 60 GHz devices have a large performance gap for the achieved communication range as well as a very low spatial reuse. However, they are still suitable for low density WLANs and for next generation aerial micro cell stations. Seeing that these COTS devices are not as directional as literature suggests, we analyze how channels are not as frequency stable as expected due to the large amount of reflected signals. Ideally, frequency selective techniques could be used in these frequency selective channels in order to enlarge the range of these 60 GHz devices. To validate this, we measure real-world 60 GHz indoor channels with a bandwidth of 2 GHz and study their behavior with respect to techniques such as bitloading, subcarrier switch-off, and waterfilling. To this end, we consider a Orthogonal Frequency-Division Multiplexing (OFDM) channel as defined in the IEEE 802.11ad standard and show that in point of fact, these techniques are highly beneficial in mmWave networks allowing for a range extension of up to 50%, equivalent to power savings of up to 7 dB. In order to increase the very limited spatial reuse of these wireless networks, we propose a centralized system that allows the network to carry out the beam training process not only to maximize power but also taking into account other stations in order to minimize interference. This system is designed to work with unmodified clients. We implement and validate our system on commercial off-the-shelf IEEE 802.11ad hardware, achieving an average throughput gain of 24.67% for TCP traffic, and up to a twofold throughput gain in specific cases.Programa de Doctorado en Multimedia y Comunicaciones por la Universidad Carlos III de Madrid y la Universidad Rey Juan CarlosPresidente: Andrés García Saavedra.- Secretario: Matilde Pilar Sánchez Fernández.- Vocal: Ljiljana Simi