Single-stage unity power factor based electronic ballast

This paper deals with the design, modeling, analysis and implementation of unity power factor (UPF) based electronic ballast for a fluorescent lamp (FL). The proposed electronic ballast uses a boost AC–DC converter as a power factor corrector (PFC) to improve the power quality at the input ac mains. In this single-stage UPF based electronic ballast, boost PFC converter and a half bridge series resonant inverter (HBSRI) share a common power switch. Thus one power switch is reduced as compared to the conventional two-stage approach. The design, modeling, analysis and implementation of this topology were carried out in MATLAB-Simulink environment for a T8 36 W, 220 V, 50 Hz fluorescent lamp. The switching frequency was kept more than the resonant frequency of the inverter, to ensure the zero voltage switching (ZVS) operation of both power switches. This resulted in reduction of high frequency switching losses. The power quality parameters such as displacement power factor (DPF), distortion factor (DF), power factor (PF), crest factor (CF) and total harmonic distortion of ac mains current (THDi) were evaluated to analyze the performance of proposed electronic ballast. Test results on a developed prototype of PFC electronic ballast were included to validate the design and simulated results

A Dimmable Resonant Inverter Electronic Ballast with Unity Power Factor

The conventional line-frequency magnetic ballast is heavy and bulky, which is too kept inside the compact fluorescent lamp (CFL). The paper describes about single stage dimmable electronic ballast with very high power factor and its high efficiency. A compact lamp power circuit is designed by using integrating a buck boost power factor corrector with a current-fed resonant inverter. Then the integration process gives a single power-processing unit that minimizes the number of circuit components. In this paper the proposed resonant inverter will reduces the circulating current in the resonant tank. It also allows simple gate drivers to be used so that isolation devices can be eliminated. The design, analysis and simulation were done using MATLAB SIMULINK. DOI: 10.17762/ijritcc2321-8169.150511

High frequency electronic ballast provides line frequency lamp current

Most electronic ballasts for fluorescent lamps provide a sinusoidal lamp current at the switching frequency. The high-frequency current flowing through the lamp can generate significant radiated noise, which is unacceptable in noise-sensitive applications, such as fluorescent lights in airplanes. Using shielded enclosures for the lamps may solve the problem, but it is expensive. A discontinuous conduction mode (DCM) electronic ballast topology is presented which drives the lamp with line frequency current, just like a magnetic ballast. However, compared to a magnetic ballast, its weight is substantially reduced due to operation at 40 kHz switching frequency. The topology also ensures unity power factor at the input and stable lamp operation at the output

A Single-Stage LED Driver Based on ZCDS Class-E Current-Driven Rectifier as a PFC for Street-Lighting Applications

This paper presents a light-emitting diode (LED) driver for street-lighting applications that uses a resonant rectifier as a power-factor corrector (PFC). The PFC semistage is based on a zero-current and zero-derivative-switching (ZCDS) Class-E current-driven rectifier, and the LED driver semistage is based on a zero-voltage-switching (ZVS) Class-D LLC resonant converter that is integrated into a single-stage topology. To increase the conduction angle of the bridge-rectifier diodes current and to decrease the current harmonics that are injected in the utility line, the ZCDS Class-E rectifier is placed between the bridge-rectifier and a dc-link capacitor. The ZCDS Class-E rectifieris driven by a high-frequency current source, which is obtained from a square-wave output voltage of the ZVS Class-D LLC resonant converter using a matching network. Additionally, the proposed converter has a soft-switching characteristic that reduces switching losses and switching noise. A prototype for a 150-W LED street light has been developed and tested to evaluate the performance of the proposed approach. The proposed LED driver had a high efficiency (>91%), a high PF (>0.99), and a low total harmonic distortion (THD i <; 8%) under variation of the utility-line input voltage from 180 to 250 V rms . These experimental results demonstrate the feasibility of the proposed LED scheme

A physically based fluorescent lamp model for a SPICE or a simulink environment

This paper describes a method of modeling fluorescent lamps. The lamp model can be implemented in all major circuit simulation software packages, an example has been given for SPICE and Simulink. The model is based upon a simplified set of physical equations that gives the model validity over a wider range of operating conditions than current fluorescent lamp SPICE models allow for. The model can be used to model any low-pressure mercury-buffer gas fluorescent lamps by entering key lamp parameters, length, radius, cold-spot temperature, and buffer gas fill pressure. If fill pressure is not known, a default value dependent on lamp radius is used. The model shows good agreement over a wide range of operating frequencies and lamp powers

Power HBT reliability for space applications

High power HBT process developed by UMS for X-band application have been space evaluated under CNES and ESA funding.The reliability assessment plan features high temperatures storage tests,DC life-tests,RF step test stress,ESD and radiation tests.A set of evaluation test vehicles was defined for this purpose.Activation energy have been determined,failure rate calculations are in line with the space requirement

SINGLE STAGE LOW FREQUENCY ELECTRONIC BALLAST FOR HID LAMPS

The paper presents a single-stage high-power-factor electronic ballast for metal halide lamps. The proposed ballast integrates a buck-boost converter, a buck converter and a full-bridge inverter into a single power conversion circuit. The buck-boost converter served as a power factor corrector (PFC) is designed to operate at discontinuous conduction mode (DCM) to achieve nearly a unity power factor at the input line. By adjusting the duty-ratio of the active switches of the PFC, the lamp power is remained at rated value for universal input voltage ranged from 90 Vrms to 264 Vrms. The four active switches of the full-bridge inverter, an inductor and a capacitor form a bidirectional buck converter which supplies a low frequency square-wave currentfor the lamp at to avoid the lamp from happing acoustic resonance. The circuit operation is analyzed in detail to derive the design equations. A prototype electronic ballast for a 70 W metal halide lamp is built and tested

DESIGN OF ELECTRONIC BALLAST OF ONE BALLAST-TWO LAMP SYSTEM USING RAPID START TECHNIQUE

This project is about designing electronic ballast of one ballast–two lamp system using rapid start technique. Rapid start technique will start lamps quickly without flicker by heating the lamps electrodes and simultaneously applying the starting voltage. Rapid start technique is chosen because it provides a low starting voltage about 3.5 volts to the electrodes for one second before lamp ignition. The proposed circuit design consists of full bridge rectifier and boost converter, as a power factor correction (PFC) stage, integrate with a resonant half bridge inverter, used as lamp power control stage. Two lamps connection in parallel will be used as load to verify the objective. All the development of designing electronic ballast using one ballast–two lamp system with rapid start technique and the simulation will be through Multisim. This project is aim to design and improve the electronic ballast based on initial voltage and initial current. It is found that the current to the load is lower when two lamps are used

Evaluation of Losses in HID Electronic Ballast Using Silicon Carbide MOSFETs

HID lamps are used in applications where high luminous intensity is desired. They are used in a wide range of applications from gymnasiums to movie theatres, from parking lots to indoor aquaria, from vehicle headlights to indoor gardening. They require ballasts during start-up and also during operation to regulate the voltage and current levels. Electronic ballasts have advantages of less weight, smooth operation, and less noisy over electromagnetic ballasts. A number of topologies are available for the electronic ballast where control of power electronic devices is exploited to achieve the performance of a ballast for lighting. A typical electronic ballast consists of a rectifier, power factor control unit, and the resonant converter unit. Power factor correction (PFC) was achieved using a boost converter topology and average current mode control for gate control of the boost MOSFET operating at a frequency of 70 kHz. The PFC was tested with Si and SiC MOSFET at 250 W resistive load for varying input from 90 V to 264 V. An efficiency as high as 97.4% was achieved by Si MOSFET based PFC unit. However, for SiC MOSFET, the efficiency decreased and was lower than expected. A maximum efficiency of 97.2% was achieved with the SiC based PFC. A simulation model was developed for both Si and SiC MOSFET based ballasts. The efficiency plots are presented. A faster gate drive for SiC MOSFET could improve the efficiency of the SiC based systems