A Single-Stage LED Driver Based on ZCDS Class-E Current-Driven Rectifier as a PFC for Street-Lighting Applications

This paper presents a light-emitting diode (LED) driver for street-lighting applications that uses a resonant rectifier as a power-factor corrector (PFC). The PFC semistage is based on a zero-current and zero-derivative-switching (ZCDS) Class-E current-driven rectifier, and the LED driver semistage is based on a zero-voltage-switching (ZVS) Class-D LLC resonant converter that is integrated into a single-stage topology. To increase the conduction angle of the bridge-rectifier diodes current and to decrease the current harmonics that are injected in the utility line, the ZCDS Class-E rectifier is placed between the bridge-rectifier and a dc-link capacitor. The ZCDS Class-E rectifieris driven by a high-frequency current source, which is obtained from a square-wave output voltage of the ZVS Class-D LLC resonant converter using a matching network. Additionally, the proposed converter has a soft-switching characteristic that reduces switching losses and switching noise. A prototype for a 150-W LED street light has been developed and tested to evaluate the performance of the proposed approach. The proposed LED driver had a high efficiency (>91%), a high PF (>0.99), and a low total harmonic distortion (THD i <; 8%) under variation of the utility-line input voltage from 180 to 250 V rms . These experimental results demonstrate the feasibility of the proposed LED scheme

A general approach to synthesis and analysis of quasi-resonant converters

A method for systematic synthesis of quasi-resonant (QR) topologies by addition of resonant elements to a parent pulse-width modulation (PWM) converter network is proposed. It is found that there are six QR classes with two resonant elements, including two novel classes. More complex QR converters can be generated by a recursive application of the synthesis method. Topological definitions of all known and novel QR classes follow directly from the synthesis method and topological properties of PWM parents. The synthesis of QR converters is augmented by a study of possible switch realizations and operating modes. In particular, it is demonstrated that a controllable rectifier can be used to accomplish the constant-frequency control in all QR classes. Links between the QR converters and the underlying PWM networks are extended to general DC and small-signal AC models in which the model of the PWM parent is explicitly exposed. Results of steady-state analyses of selected QR classes and operating modes include boundaries of operating regions, DC characteristics, a comparison of switching transitions and switch stresses, and a discussion of relevant design trade-offs

Solid-state transformers in locomotives fed through AC lines: A review and future developments

One of the most important innovation expectation in railway electrical equipment is the replacement of the on-board transformer with a high power converter. Since the transformer operates at line-frequency (i.e., 50 Hz or 16 2/3 Hz), it represents a critical component from weight point of view and, moreover, it is characterized by quite poor efficiency. High power converters for this application are characterized by a medium frequency inductive coupling and are commonly referred as Power Electronic Transformers (PET), Medium Frequency Topologies or Solid-State Transformers (SST). Many studies were carried out and various prototypes were realized until now, however, the realization of such a system has some difficulties, mainly related to the high input voltage (i.e., 25 kV for 50 Hz lines and 15 kV for 16 2/3 Hz lines) and the limited performance of available power electronic switches. The aim of this study is to present a survey on the main solutions proposed in the technical literature and, analyzing pros and cons of these studies, to introduce new possible circuit topologies for this application

Soft-switching cells for Modular Multilevel Converters for efficient grid integration of renewable sources

The Modular Multilevel Converter (MMC) concept is a modern energy conversion structure that stands out for a number of interesting features that opens wide application chances in Power Systems, for example for efficient grid integration of renewable sources. In these high-voltage, high-power application fields, a high efficiency is mandatory. In this regard, an interesting and promising development opportunity could be to make soft-switching the elementary converters of the submodules (cells), half H-bridges or full H-bridges, obtaining at the same time the advantage of increasing the switching frequency. The-Active Resonant Commutated Pole Converter (ARCP) or the Auxiliary Quasi Resonant DC-link Inverter (AQRDCL) soft-switching topologies appear adequate for this purpose. This paper is dedicated to examining these development possibilities

Resonance mode power supplies with power factor correction

There is an increasing need for AC-DC converters to draw a pure sinusoidal current at near unity power factor from the AC mains. Most conventional power factor correcting systems employ PWM techniques to overcome the poor power factor being presented to the mains. However, the need for smaller and lighter power processing equipment has motivated the use of higher internal conversion frequencies in the past. In this context, resonant converters are becoming a viable alternative to the conventional PWM controlled power supplies. The thesis presents the implementation of active power factor correction in power supplies, using resonance mode techniques. It reviews the PWM power factor correction circuit topologies previously used. The possibility of converting these PWM topologies to resonant mode versions is discussed with a critical assessment as to the suitability of the semiconductor switching devices available today for deployment in these resonant mode supplies. The thesis also provides an overview of the methods used to model active semiconductor devices. The computer modelling is done using the PSpice microcomputer simulation program. The modifications that are needed to the built in MOSFET model in PSpice, when modeling high frequency circuits is discussed. A new two transistor model which replicates the action of a OTO thyristor is also presented. The new model enables the designer to estimate the device parameters with ease by adopting a short calculation and graphical design procedure, based on the manufacturer's data sheets. The need for a converter with a high efficiency, larger power/weight ratio, high input power factor with reduced line current distortion and reduced cost has led to the development of a new resonant mode converter topology, for power processing. The converter presents a near resistive load to the mains thus ensuring a high input power factor, while providing a stabilised de voltage at the output with a small lOOHz ripple. The supply is therefore ideal for preregulation applications. A description of the modes of operation and the analysis of the power circuit are included in the thesis. The possibility of using the converter for low output voltage applications is also discussed. The design of a 300W, 80kHz prototype model of this circuit is presented in the thesis. The design of the isolation transformer and other magnetic components are described in detail. The selection of circuit components and the design and implementation of the variable frequency control loop are also discussed. An evaluation of the experimental and computer simulated results obtained from the prototype model are included in the presentation. The thesis further presents a zero-current switching quasi-resonant flyback circuit topology with power factor correction. The reasons for using this topology for off-line power conversion applications are discussed. The use of a cascoded combination of a bipolar power transistor and two power MOSFETs i~ the configuration has enabled the circuit to process moderate levels of power while simultaneously switching at high frequencies. This fulfils the fundamental precondition for miniaturisation. It also provides a well regulated DC output voltage with a very small ripple while maintaining a high input power factor. The circuit is therefore ideal for use in mobile applications. A preliminary design of the above circuit, its analysis using PSpice, the design of the control circuit, current limiting and overcurrent protection circuitry and the implementation of closed-loop control are all included in the thesis. The experimental results obtained from a bread board model is also presented with an evaluation of the circuit performance. The power factor correction circuit is finally installed in this supply and the overall converter performance is assessed

Soft-switching modular multilevel converters for efficient grid integration of renewable sources

The Modular Multilevel Converter (MMC) concept is a modern energy conversion structure that stands out for a number of interesting features that opens wide application chances in Power Systems, for example for efficient grid integration of renewable sources. In these high-voltage, high-power application fields, a high efficiency is mandatory. In this regard, an interesting and promising development opportunity could be to make soft-switching the elementary converters of the submodules (cells), half H-bridges or full H-bridges, obtaining at the same time the advantage of increasing the switching frequency. The ARCP or the AQRDCL soft-switching topologies appear adequate for this purpose. This paper is dedicated to examining these development possibilities

Uninterruptible power supply system using a dual converter in quasi-resonant mode

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.Uninterruptible Power Supply (UPS) systems have become a standard to protect electronic devices such as servers and host computers. Also, the energy supply of whole buildings is linked with large UPS systems to ensure a steady power flow. Two system configurations are widely used which differ in price and their ability to protect very sensitive load. This thesis illustrates an analytical examination of all existing systems and concludes with the finding of new configurations with increased efficiency and reduced costs. A dual converter is proposed as the heart of the new UPS system. This converter links the necessary two sources of the UPS through a common transformer. The transformer operates at a high frequency which is enabled due to the resonant switching technique used. The results of this paper were achieved using mathematical analysis, electrical and electro-magnetic simulation as well as by experiments carried out on the self designed circuit boards in the laboratory. These boards were built in a modular way to enable series testing and thereby optimise the dimensioning of the system.This work is the result of a collaborative project between the BRUNEL UNIVERSITY WEST LONDON,U.K. and the FACHHOCHSCHULE FUR TECHNIK ESSLINGEN, GERMANY

Single-Switch Non-Isolated Resonant DC-DC Converter for Single-Input Dual-Output Applications

This paper describes a new configuration of Cuk and SEPIC (Single-Ended Primary Converter) ZVS-QR (zero-voltage switching quasi-resonant) combination DC-DC converter for bipolar output with a single switch. The proposed topology employs a single ground-referenced power switch, which simplifies the gate drive design with a single L-C resonant network and provides a bipolar output voltage with good regulation, acceptable efficiency and a step-down/up conversion ratio. This configuration provides dual-output voltage by switching the power switch to zero voltage, which is an interesting alternative for many applications where small size, light weight and high power density are very important aspects. In order to verify its performance, a SEPIC–Cuk Combination ZVS-QR prototype with a cost-effective commercial resonant controller was designed and tested. The experimental results show that the proposed combined topology is suitable for Single-Input Dual-Output (SIDO) applications

Analysis and design of a modular multilevel converter with trapezoidal modulation for medium and high voltage DC-DC transformers

Conventional dual active bridge topologies provide galvanic isolation and soft-switching over a reasonable operating range without dedicated resonant circuits. However, scaling the two-level dual active bridge to higher dc voltage levels is impeded by several challenges among which the high dv/dt stress on the coupling transformer insulation. Gating and thermal characteristics of series switch arrays add to the limitations. To avoid the use of standard bulky modular multilevel bridges, this paper analyzes an alternative modulation technique where staircase approximated trapezoidal voltage waveforms are produced; thus alleviating developed dv/dt stresses. Modular design is realized by the utilization of half-bridge chopper cells. Therefore, the analyzed converter is a modular multi-level converter operated in a new mode with no common-mode dc arm currents as well as reduced capacitor size, hence reduced cell footprint. Suitable switching patterns are developed and various design and operation aspects are studied. Soft switching characteristics will be shown to be comparable to those of the two-level dual active bridge. Experimental results from a scaled test rig validate the presented concept

High-power converters for space applications

Phase 1 was a concept definition effort to extend space-type dc/dc converter technology to the megawatt level with a weight of less than 0.1 kg/kW (220 lb./MW). Two system designs were evaluated in Phase 1. Each design operates from a 5 kV stacked fuel cell source and provides a voltage step-up to 100 kV at 10 A for charging capacitors (100 pps at a duty cycle of 17 min on, 17 min off). Both designs use an MCT-based, full-bridge inverter, gaseous hydrogen cooling, and crowbar fault protection. The GE-CRD system uses an advanced high-voltage transformer/rectifier filter is series with a resonant tank circuit, driven by an inverter operating at 20 to 50 kHz. Output voltage is controlled through frequency and phase shift control. Fast transient response and stability is ensured via optimal control. Super-resonant operation employing MCTs provides the advantages of lossless snubbing, no turn-on switching loss, use of medium-speed diodes, and intrinsic current limiting under load-fault conditions. Estimated weight of the GE-CRD system is 88 kg (1.5 cu ft.). Efficiency of 94.4 percent and total system loss is 55.711 kW operating at 1 MW load power. The Maxwell system is based on a resonance transformer approach using a cascade of five LC resonant sections at 100 kHz. The 5 kV bus is converted to a square wave, stepped-up to a 100 kV sine wave by the LC sections, rectified, and filtered. Output voltage is controlled with a special series regulator circuit. Estimated weight of the Maxwell system is 83.8 kg (4.0 cu ft.). Efficiency is 87.2 percent and total system loss is 146.411 kW operating at 1 MW load power