Contact resistances in trigate and FinFET devices in a Non-Equilibrium Green's Functions approach

We compute the contact resistances $R_{\rm c}$ in trigate and FinFET devices with widths and heights in the 4 to 24 nm range using a Non-Equilibrium Green's Functions approach. Electron-phonon, surface roughness and Coulomb scattering are taken into account. We show that $R_{\rm c}$ represents a significant part of the total resistance of devices with sub-30 nm gate lengths. The analysis of the quasi-Fermi level profile reveals that the spacers between the heavily doped source/drain and the gate are major contributors to the contact resistance. The conductance is indeed limited by the poor electrostatic control over the carrier density under the spacers. We then disentangle the ballistic and diffusive components of $R_{\rm c}$, and analyze the impact of different design parameters (cross section and doping profile in the contacts) on the electrical performances of the devices. The contact resistance and variability rapidly increase when the cross sectional area of the channel goes below $\simeq 50$ nm$^2$. We also highlight the role of the charges trapped at the interface between silicon and the spacer material.Comment: 16 pages, 15 figure

Perspective of buried oxide thickness variation on triple metal-gate (TMG) recessed-S/D FD-SOI MOSFET

Recently, Fully-Depleted Silicon on Insulator (FD-SOI) MOSFETs have been accepted as a favourable technology beyond nanometer nodes, and the technique of Recessed-Source/Drain (Re-S/D) has made it more immune in regards of various performance factors. However, the proper selection of Buried-Oxide (BOX) thickness is one of the major challenges in the design of FD-SOI based MOS devices in order to suppress the drain electric penetrations across the BOX interface efficiently. In this work, the effect of BOX thickness on the performance of TMG Re-S/D FD-SOI MOSFET has been presented at 60 nm gate length. The perspective of BOX thickness variation has been analysed on the basis of its surface potential profile and the extraction of the threshold voltage by performing two-dimensional numerical simulations. Moreover, to verify the short channel immunity, the impact of gate length scaling has also been discussed. It is found that the device attains two step-up potential profile with suppressed short channel effects. The outcomes reveal that the Drain Induced Barrier Lowering (DIBL) values are lower among conventional SOI MOSFETs. The device has been designed and simulated by using 2D numerical ATLAS Silvaco TCAD simulator

Impact of the Trap Attributes on the Gate Leakage Mechanisms in a 2D MS-EMC Nanodevice Simulator

From a modeling point of view, the inclusion of adequate physical phenomena is mandatory when analyzing the behavior of new transistor architectures. In particular, the high electric field across the ultra-thin insulator in aggressively scaled transistors leads to the possibility for the charge carriers in the channel to tunnel through the gate oxide via various gate leakage mechanisms (GLMs). In this work, we study the impact of trap number on gate leakage using the GLM model, which is included in a Multi-Subband Ensemble Monte Carlo (MS-EMC) simulator for Fully-Depleted Silicon-On-Insulator (FDSOI) field effect transistors (FETs). The GLM code described herein considers both direct and trap-assisted tunneling. This work shows that trap attributes and dynamics can modify the device electrostatic characteristics and even play a significant role in determining the extent of GLMs.The research leading to these results has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 688101 SUPERAID7

Developing ultrasensitive and CMOS compatible ISFETs in the BEOL of industrial UTBB FDSOI transistors

Le marché des capteurs a récemment connu une croissance spectaculaire alimentée par l'application remarquable de capteurs dans l'électronique de consommation, l'industrie de l'automatisation, les appareils portables, le secteur automobile et l'internet des objets de plus en plus adopté. La technologie avancée des complementary metal oxide semiconductor (CMOS), les technologies de nano et de micro-fabrication et les plateformes de synthèse de matériaux innovantes sont également des moteurs du développement incroyable de l'industrie des capteurs. Ces progrès ont permis la réalisation de capteurs dotés de nombreuses caractéristiques telles que la précision accrue, les dimensions miniaturisées, l’intégrabilité, la production de masse, le coût très réduit et le temps de réponse rapide. Les ion-sensitive field-effect transistors (ISFETs) sont des capteurs à l'état solide (bio) chimiques, destinés à la détection des ions H+ (pH), Na+ et K+. Malgré cela, la commercialisation des ISFETs est encore à ses balbutiements, après près de cinq décennies de recherche et développement. Cela est dû principalement à la sensibilité limitée, à la controverse sur l'utilisation de l'électrode de référence pour le fonctionnement des ISFETs et à des problèmes de stabilité. Dans cette thèse, les ISFETs ultrasensibles et compatibles CMOS sont intégrés dans le BEOL des transistors UTBB FDSOI standard. Un circuit diviseur capacitif est utilisé pour polariser la grille d’avant afin d'assurer des performances stables du capteur. En exploitant la fonction d’amplification intrinsèque fournie par les transistors UTBB FDSOI, nous avons présenté des ISFET ultra sensibles. L'amplification découle du fort couplage électrostatique entre la grille avant et la grille arrière du FDSOI et des capacités asymétriques des deux grilles. Un changement de tension au niveau de la grille avant apparaît sur la grille arrière sous la forme d'un décalage amplifié de la tension. L'amplification, représentée par le facteur de couplage (γ), est égale au rapport de la capacité de l'oxyde de grille et de la capacité de le buried oxide (BOX). Par conséquent, en fonctionnalisant la détection du pH sur la grille avant pour les dispositifs FDSOI, la modification du potentiel de surface sur la grille avant est détectée par la grille arrière et amplifiée du facteur de couplage (γ), donnant lieu à un capteur chimique à l'état solide à sensibilité ultra-élevée. L'intégration de la fonctionnalité de détection a été réalisée en back end of line (BEOL), ce qui offre les avantages d'une fiabilité et d'une durée de vie accrues du capteur, d'une compatibilité avec le processus CMOS standard et d'une possibilité d'intégration d'un circuit diviseur capacitif. Le fonctionnement des MOSFETs, sans une polarisation appropriée de la grille avant, les rend vulnérables aux effets de grilles flottantes indésirables. Le circuit diviseur capacitif résout ce problème en polarisant la grille avant tout enmaintenant la fonctionnalité de détection sur la même grille par un couplage capacitif au métal commun du BEOL. Par conséquent, le potentiel au niveau du métal BEOL est une somme pondérée du potentiel de surface au niveau de la grille de détection et de la polarisation appliquée au niveau de la grille de contrôle. Le capteur proposé est modélisé et simulé à l'aide de TCAD-Sentaurus. Un modèle mathématique complet a été développé. Il fournit la réponse du capteur en fonction du pH de la solution (entrée du capteur) et des paramètres de conception du circuit diviseur capacitif et du transistor UTBB FDSOI. Dans ce cas, des résultats cohérents ont été obtenus des travaux de modélisation et de simulation, avec une sensibilité attendue de 780 mV / pH correspondant à un film de détection ayant une réponse de Nernst. La modélisation et la simulation du capteur proposé ont également été validées par une fabrication et une caractérisation du capteur de pH à grille étendue avec validation de son concept. Ces capteurs ont été développés par un traitement séparé du composant de détection de pH, qui est connecté électriquement au transistor uniquement lors de la caractérisation du capteur. Ceci permet une réalisation plus rapide et plus simple du capteur sans avoir besoin de masques et de motifs par lithographie. Les capteurs à grille étendue ont présenté une sensibilité de 475 mV/pH, ce qui est supérieur aux ISFET de faible puissance de l'état de l’art. Enfin, l’intégration de la fonctionnalité de détection directement dans le BEOL des dispositifs FDSOI UTBB a été poursuivie. Une sensibilité expérimentale de 730 mV/pH a été obtenue, ce qui confirme le modèle mathématique et la réponse simulée. Cette valeur est 12 fois supérieure à la limite de Nernst et supérieure aux capteurs de l'état de l’art. Les capteurs sont également évalués pour la stabilité, la résolution, l'hystérésis et la dérive dans lesquels d'excellentes performances sont démontrées. Une nouvelle architecture de détection du pH est également démontrée avec succès, dans laquelle la détection est fonctionnalisée au niveau de la diode de protection de la grille plutôt que de la grille avant des dispositifs UTBB FDSOI. La commutation de courant abrupte, aussi basse que 9 mV/decade, pourrait potentiellement augmenter la sensibilité de polarisation fixée à 6,6 decade/pH. Nous avons démontré expérimentalement une sensibilité de 1,25 decade/pH supérieure à la sensibilité reportée à l’état de l’art.Abstract: The sensor market has recently seen a dramatic growth fueled by the remarkable application of sensors in the consumer electronics, automation industry, wearable devices, the automotive sector, and in the increasingly adopted internet of things (IoT). The advanced complementary metal oxide semiconductor (CMOS) technology, the nano and micro fabrication technologies, and the innovative material synthesis platforms are also driving forces for the incredible development of the sensor industry. These technological advancements have enabled realization of sensors with characteristic features of increased accuracy, miniaturized dimension, integrability, volume production, highly reduced cost, and fast response time. Ion-sensitive field-effect transistors (ISFETs) are solid state (bio)chemical sensors, for pH (H+), Na+, K+ ion detection, that are equipped with the promise of the highly aspired features of CMOS devices. Despite this, the commercialization of ISFETs is still at the stage of infancy after nearly five decades of research and development. This is due mainly to the limited sensitivity, the controversy over the use of the reference electrode for ISFET operation, and because of stability issues. In this thesis, ultrasensitive and CMOS compatible ISFETs are integrated in the back end of line (BEOL) of standard UTBB FDSOI transistors. A capacitive divider circuit is employed for biasing the front gate for stable performance of the sensor. Exploiting the intrinsic amplification feature provided by UTBB FDSOI transistors, we demonstrated ultrahigh sensitive ISFETs. The amplification arises from the strong electrostatic coupling between the front gate and the back gate of the FDSOI, and the asymmetric capacitances of the two gates. A change in voltage at the front gate appears at the back gate as an amplified shift in voltage. The amplification, referred to as the coupling factor (γ), is equal to the ratio of the gate oxide capacitance and the buried oxide (BOX) capacitance. Therefore, functionalizing the pH sensing at the front gate of FDSOI devices, the change in surface potential at the front gate is detected at the back gate amplified by the coupling factor (γ), giving rise to an ultrahigh-sensitive solid state chemical sensor. Integration of the sensing functionality was made in the BEOL which gives the benefits of increased reliability and life time of the sensor, compatibility with the standard CMOS process, and possibility for embedding a capacitive divider circuit. Operation of the MOSFETs without a proper front gate bias makes them vulnerable for undesired floating body effects. The capacitive divider circuit addresses these issues by biasing the front gate simultaneously with the sensing functionality at the same gate through capacitive coupling to a common BEOL metal. Therefore, the potential at the BEOL metal would be a weighted sum of the surface potential at the sensing gate and the applied bias at the control gate. The proposed sensor is modeled and simulated using TCAD-Sentaurus. A complete mathematical model is developed which provides the output of the sensor as a function of the solution pH (input to the sensor), and the design parameters of the capacitive divider circuit and the UTBB FDSOI transistor. In that case, consistent results have been obtained from the modeling and simulation works, with an expected sensitivity of 780 mV/pH corresponding to a sensing film having Nernst response. The modeling and simulation of the proposed sensor was further validated by a proof of concept extended gate pH sensor fabrication and characterization. These sensors were developed by a separated processing of just the pH sensing component, which is electrically connected to the transistor only during characterization of the sensor. This provides faster and simpler realization of the sensor without the need for masks and patterning by lithography. The extended gate sensors showed 475 mV/pH sensitivity which is superior to state of the art low power ISFETs. Finally, integration of the sensing functionality directly in the BEOL of the UTBB FDSOI devices was pursued. An experimental sensitivity of 730 mV/pH is obtained which is consistent with the mathematical model and the simulated response. This is more than 12-times higher than the Nernst limit, and superior to state of the art sensors. Sensors are also evaluated for stability, resolution, hysteresis, and drift in which excellent performances are demonstrated. A novel pH sensing architecture is also successfully demonstrated in which the detection is functionalized at the gate protection diode rather than the front gate of UTBB FDSOI devices. The abrupt current switching, as low as 9 mV/decade, has the potential to increase the fixed bias sensitivity to 6.6 decade/pH. We experimentally demonstrated a sensitivity of 1.25 decade/pH which is superior to the state of the art sensitivity

Numerical simulation and analytical modelling of self-heating in FDSOI MOSFETs down to very deep cryogenic temperatures

Self-heating (SHE) TCAD numerical simulations have been performed, for the first time, on 30nm FDSOI MOS transistors at extremely low temperatures. The self-heating temperature rise dTmax and the thermal resistance Rth are computed as functions of the ambient temperature Ta and the dissipated electrical power (Pd), considering calibrated silicon and oxide thermal conductivities. The characteristics of the SHE temperature rise dTmax(Pd) display sub-linear behavior at sufficiently high levels of dissipated power, in line with standard FDSOI SHE experimental data. It has been observed that the SHE temperature rise dTmax can significantly exceed the ambient temperature more easily at very low temperatures. Furthermore, a detailed thermal analysis of the primary heat flows in the FDSOI device has been conducted, leading to the development of an analytical SHE model calibrated against TCAD simulation data. This SHE analytical model accurately describes the dTmax(Pd) and Rth(Ta) characteristics of an FDSOI MOS device operating at extreme low ambient temperatures. These TCAD simulations and analytical models hold great promise for predicting the SHE and electro-thermal performance of FDSOI MOS transistors against ambient temperature and dissipated power

Back-gate bias dependence of the statistical variability of FDSOI MOSFETs with thin BOX

The impact of back-gate bias on the statistical variability (SV) of FDSOI MOSFETs with thin buried oxide (BOX) is studied via 3-D 'atomistic' drift-diffusion simulation. The impact of the principal sources of SV, i.e., random dopant fluctuations, line edge roughness, and metal gate granularity, on threshold voltage, drain-induced barrier lowering, and drive current is studied in detail. It is shown that reverse back-bias is beneficial in terms of reducing the dispersion of the off-current and the corresponding standby leakage power, whereas forward back-bias reduces the on-current variability. The correlation coefficients between relevant figures of merit and their trends against back-bias are also studied in detail, providing guidelines for the development of statistical compact models of thin-BOX FDSOI MOSFETs for low-standby-power circuit applications. © 1963-2012 IEEE.published_or_final_versio

Impact of non uniform strain configuration on transport properties for FD14+ devices

As device dimensions are scaled down, the use of non-geometrical performance boosters becomes of special relevance. In this sense, strained channels are proposed for the 14 nm FDSOI node. However this option may introduce a new source of variability since strain distribution inside the channel is not uniform at such scales. In this work, a MS-EMC study of different strain configurations including non-uniformities is presented showing drain current degradation because of the increase of intervalley phonon scattering and the subsequent variations of transport effective mass and drift velocity. This effect, which has an intrinsic statistical origin, will make necessary further optimizations to keep the expected boosting capabilities of strained channels

Static random-access memory designs based on different FinFET at lower technology node (7nm)

Title from PDF of title page viewed January 15, 2020Thesis advisor: Masud H ChowdhuryVitaIncludes bibliographical references (page 50-57)Thesis (M.S.)--School of Computing and Engineering. University of Missouri--Kansas City, 2019The Static Random-Access Memory (SRAM) has a significant performance impact on current nanoelectronics systems. To improve SRAM efficiency, it is important to utilize emerging technologies to overcome short-channel effects (SCE) of conventional CMOS. FinFET devices are promising emerging devices that can be utilized to improve the performance of SRAM designs at lower technology nodes. In this thesis, I present detail analysis of SRAM cells using different types of FinFET devices at 7nm technology. From the analysis, it can be concluded that the performance of both 6T and 8T SRAM designs are improved. 6T SRAM achieves a 44.97% improvement in the read energy compared to 8T SRAM. However, 6T SRAM write energy degraded by 3.16% compared to 8T SRAM. Read stability and write ability of SRAM cells are determined using Static Noise Margin and N- curve methods. Moreover, Monte Carlo simulations are performed on the SRAM cells to evaluate process variations. Simulations were done in HSPICE using 7nm Asymmetrical Underlap FinFET technology. The quasiplanar FinFET structure gained considerable attention because of the ease of the fabrication process [1] – [4]. Scaling of technology have degraded the performance of CMOS designs because of the short channel effects (SCEs) [5], [6]. Therefore, there has been upsurge in demand for FinFET devices for emerging market segments including artificial intelligence and cloud computing (AI) [8], [9], Internet of Things (IoT) [10] – [13] and biomedical [17] –[18] which have their own exclusive style of design. In recent years, many Underlapped FinFET devices were proposed to have better control of the SCEs in the sub-nanometer technologies [3], [4], [19] – [33]. Underlap on either side of the gate increases effective channel length as seen by the charge carriers. Consequently, the source-to-drain tunneling probability is improved. Moreover, edge direct tunneling leakage components can be reduced by controlling the electric field at the gate-drain junction . There is a limitation on the extent of underlap on drain or source sides because the ION is lower for larger underlap. Additionally, FinFET based designs have major width quantization issue. The width of a FinFET device increases only in quanta of silicon fin height (HFIN) [4]. The width quantization issue becomes critical for ratioed designs like SRAMs, where proper sizing of the transistors is essential for fault-free operation. FinFETs based on Design/Technology Co-Optimization (DTCO_F) approach can overcome these issues [38]. DTCO_F follows special design rules, which provides the specifications for the standard SRAM cells with special spacing rules and low leakages. The performances of 6T SRAM designs implemented by different FinFET devices are compared for different pull-up, pull down and pass gate transistor (PU: PD:PG) ratios to identify the best FinFET device for high speed and low power SRAM applications. Underlapped FinFETs (UF) and Design/Technology Co-Optimized FinFETs (DTCO_F) are used for the design and analysis. It is observed that with the PU: PD:PG ratios of 1:1:1 and 1:5:2 for the UF-SRAMs the read energy has degraded by 3.31% and 48.72% compared to the DTCO_F-SRAMs, respectively. However, the read energy with 2:5:2 ratio has improved by 32.71% in the UF-SRAM compared to the DTCO_F-SRAMs. The write energy with 1:1:1 configuration has improved by 642.27% in the UF-SRAM compared to the DTCO_F-SRAM. On the other hand, the write energy with 1:5:2 and 2:5:2 configurations have degraded by 86.26% and 96% in the UF-SRAMs compared to the DTCO_F-SRAMs. The stability and reliability of different SRAMs are also evaluated for 500mV supply. From the analysis, it can be concluded that Asymmetrical Underlapped FinFET is better for high-speed applications and DTCO FinFET for low power applications.Introduction -- Next generation high performance device: FinFET -- FinFET based SRAM bitcell designs -- Benchmarking of UF-SRAMs and DTCO-F-SRAMS -- Collaborative project -- Internship experience at INTEL and Marvell Semiconductor -- Conclusion and future wor

Characterization of 28 nm FDSOI MOS and application to the design of a low-power 2.4 GHz LNA

IoT is expected to connect billions of devices all over world in the next years, and in a near future, it is expected to use LR-WPAN in a wide variety of applications. Not all the devices will require of high performance but will require of low power hungry systems since most of them will be powered with a battery. Conventional CMOS technologies cannot cover these needs even scaling it to very small regimes, which appear other problems. Hence, new technologies are emerging to cover the needs of this devices. One promising technology is the UTBB FDSOI, which achieves good performance with very good energy efficiency. This project characterizes this technology to obtain a set of parameters of interest for analog/RF design. Finally, with the help of a low-power design methodology (gm/Id approach), a design of an ULP ULV LNA is performed to check the suitability of this technology for IoT

Atlas simulation based study of recessed source/drain SOI mosfets

Front gate and back gate threshold voltage, potential distributions and sub threshold swing of recessed source/drain ultra-thin body silicon on insulator mosfets are simulated and analyzed in a vivid manner with extreme meticulousness. Analysis and comparative study of the electrical characteristics of Re s/d UTB SOI mosfets with that of conventional FD SOI mosfets has been done. Structures of conventional soi mosfet and Re s/d mosfets is simulated with the help of software like ATLAS