A Survey on the Best Choice for Modulus of Residue Code

Nowadays, the development of technology and the growing need for dense and complex chips have led chip industries to increase their attention on the circuit testability. Also, using the electronic chips in certain industries, such as the space industry, makes the design of fault tolerant circuits a challenging issue. Coding is one of the most suitable methods for error detection and correction. The residue code, as one of the best choices for error detection aims, is wildly used in large arithmetic circuits such as multiplier and also finds a wide range of applications in processors and digital filters. The modulus value in this technique directly effect on the area overhead parameter. A large area overhead is one of the most important disadvantages especially for testing the small circuits. The purpose of this paper is to study and investigate the best choice for residue code check base that is used for simple and small circuits such as a simple ripple carry adder. The performances are evaluated by applying stuck-at-faults and transition-faults by simulators. The efficiency is defined based on fault coverage and normalized area overhead. The results show that the modulus 3 with 95% efficiency provided the best result. Residue code with this modulus for checking a ripple carry adder, in comparison with duplex circuit, 30% improves the efficiency

Area/latency optimized early output asynchronous full adders and relative-timed ripple carry adders

This article presents two area/latency optimized gate level asynchronous full adder designs which correspond to early output logic. The proposed full adders are constructed using the delay-insensitive dual-rail code and adhere to the four-phase return-to-zero handshaking. For an asynchronous ripple carry adder (RCA) constructed using the proposed early output full adders, the relative-timing assumption becomes necessary and the inherent advantages of the relative-timed RCA are: (1) computation with valid inputs, i.e., forward latency is data-dependent, and (2) computation with spacer inputs involves a bare minimum constant reverse latency of just one full adder delay, thus resulting in the optimal cycle time. With respect to different 32-bit RCA implementations, and in comparison with the optimized strong-indication, weak-indication, and early output full adder designs, one of the proposed early output full adders achieves respective reductions in latency by 67.8, 12.3 and 6.1 %, while the other proposed early output full adder achieves corresponding reductions in area by 32.6, 24.6 and 6.9 %, with practically no power penalty. Further, the proposed early output full adders based asynchronous RCAs enable minimum reductions in cycle time by 83.4, 15, and 8.8 % when considering carry-propagation over the entire RCA width of 32-bits, and maximum reductions in cycle time by 97.5, 27.4, and 22.4 % for the consideration of a typical carry chain length of 4 full adder stages, when compared to the least of the cycle time estimates of various strong-indication, weak-indication, and early output asynchronous RCAs of similar size. All the asynchronous full adders and RCAs were realized using standard cells in a semi-custom design fashion based on a 32/28 nm CMOS process technology

Techniques for the realization of ultrareliable spaceborne computers Interim scientific report

Error-free ultrareliable spaceborne computer

Fault-tolerant computer study

A set of building block circuits is described which can be used with commercially available microprocessors and memories to implement fault tolerant distributed computer systems. Each building block circuit is intended for VLSI implementation as a single chip. Several building blocks and associated processor and memory chips form a self checking computer module with self contained input output and interfaces to redundant communications buses. Fault tolerance is achieved by connecting self checking computer modules into a redundant network in which backup buses and computer modules are provided to circumvent failures. The requirements and design methodology which led to the definition of the building block circuits are discussed

Tracing Fault Effects in FPGA Systems

The paper presents the extent of fault effects in FPGA based systems and concentrates on transient faults (induced by single event upsets – SEUs) within the configuration memory of FPGA. An original method of detailed analysis of fault effect propagation is presented. It is targeted at microprocessor based FPGA systems using the developed fault injection technique. The fault injection is performed at HDL description level of the microprocessor using special simulators and developed supplementary programs. The proposed methodology is illustrated for soft PicoBlaze microprocessor running 3 programs. The presented results reveal some problems with fault handling at the software level.

A NEW APPROACH OF AN ERROR DETECTING AND CORRECTING CIRCUIT BY ARITHMETIC LOGIC BLOCKS

This paper proposes a unique method of an error detection and correction (EDAC) circuit, carried out using arithmetic logic blocks. The modified logic blocks circuit and its auxiliary components are designed with Boolean and block reduction technique, which reduced one logic gate per block. The reduced logic circuits were simulated and designed using MATLAB Simulink, DSCH 2 CAD, and Microwind CAD tools. The modified, 2:1 multiplexer, demultiplexer, comparator, 1-bit adder, ALU, and error correction and detection circuit were simulated using MATLAB and Microwind. The EDAC circuit operates at a speed of 454.676 MHz and a slew rate of -2.00 which indicates excellence in high speed and low-area.