Supply modulator ripple in envelope tracking systems - effects and countermeasures

Envelope tracking power amplifiers (ET PAs) are one of the promising architectures to provide high efficiency amplification for future wireless communication systems. This is due to their ability to offer high efficiency over a wide output power range, by modulating the supply voltage applied to the PA. Generating this dynamic supply voltage with switching-mode modulators is highly efficient, but filtering the output remains a challenge, resulting in a residual `ripple' on the supply voltage. This paper presents an experimental investigation into the interaction between a PA and a supply modulator in the presence of this ripple. By adding a varying ripple magnitude to the modulated drain voltage of a 2.14 GHz GaN ET PA with a 10 MHz LTE signal, the effects on the linearity of the RFPA can be observed and analysed to allow the system designer an insight into the amount of ripple that is tolerable, while still being able to achieve linearity and efficiency targets. The mixing products of the ripple and RF signal are shown to be a potential issue in ET PAs. This paper shows, for the first time, the full impact of the ripple voltage magnitude on the output spectrum. Further more, the ripple sensitivity of two different ET PA linearisation approaches are explored; firstly applying generic memory polynomial digital pre-distortion (DPD) and secondly optimising the ET tracking signal shaping function to improve linearity. Measurements show that for the case where the ripple and RF are not synchronized, neither approach is able to significantly mitigate the ripple effect on the PA linearity

Advanced digital modulation: Communication techniques and monolithic GaAs technology

Communications theory and practice are merged with state-of-the-art technology in IC fabrication, especially monolithic GaAs technology, to examine the general feasibility of a number of advanced technology digital transmission systems. Satellite-channel models with (1) superior throughput, perhaps 2 Gbps; (2) attractive weight and cost; and (3) high RF power and spectrum efficiency are discussed. Transmission techniques possessing reasonably simple architectures capable of monolithic fabrication at high speeds were surveyed. This included a review of amplitude/phase shift keying (APSK) techniques and the continuous-phase-modulation (CPM) methods, of which MSK represents the simplest case

Linear Operation of Switch-Mode Outphasing Power Amplifiers

Radio transceivers are playing an increasingly important role in modern society. The ”connected” lifestyle has been enabled by modern wireless communications. The demand that has been placed on current wireless and cellular infrastructure requires increased spectral efficiency however this has come at the cost of power efficiency. This work investigates methods of improving wireless transceiver efficiency by enabling more efficient power amplifier architectures, specifically examining the role of switch-mode power amplifiers in macro cell scenarios. Our research focuses on the mechanisms within outphasing power amplifiers which prevent linear amplification. From the analysis it was clear that high power non-linear effects are correctable with currently available techniques however non-linear effects around the zero crossing point are not. As a result signal processing techniques for suppressing and avoiding non-linear operation in low power regions are explored. A novel method of digital pre-distortion is presented, and conventional techniques for linearisation are adapted for the particular needs of the outphasing power amplifier. More unconventional signal processing techniques are presented to aid linearisation of the outphasing power amplifier, both zero crossing and bandwidth expansion reduction methods are designed to avoid operation in nonlinear regions of the amplifiers. In combination with digital pre-distortion the techniques will improve linearisation efforts on outphasing systems with dynamic range and bandwidth constraints respectively. Our collaboration with NXP provided access to a digital outphasing power amplifier, enabling empirical analysis of non-linear behaviour and comparative analysis of behavioural modelling and linearisation efforts. The collaboration resulted in a bench mark for linear wideband operation of a digital outphasing power amplifier. The complimentary linearisation techniques, bandwidth expansion reduction and zero crossing reduction have been evaluated in both simulated and practical outphasing test benches. Initial results are promising and indicate that the benefits they provide are not limited to the outphasing amplifier architecture alone. Overall this thesis presents innovative analysis of the distortion mechanisms of the outphasing power amplifier, highlighting the sensitivity of the system to environmental effects. Practical and novel linearisation techniques are presented, with a focus on enabling wide band operation for modern communications standards

The digital predistorter goes multi-dimensional: DPD for concurrent multi-band envelope tracking and outphasing power amplifiers

Over at least the last two decades, digital predistortion (DPD) has become the most common and widespread solution to cope with the power amplifier's (PA's) inherent linearity-versus-efficiency tradeoff. When compared with other linearization techniques, such as Cartesian feedback or feedforward, DPD has proven able to adapt to the always-growing demands of technology: wider bandwidths, stringent spectrum masks, and reconfigurability. The principles of predistortion linearization (in its analog or digital forms) are straightforward, and the linearization subsystem precedes the PA (a nonlinear function in a digital signal processor in the case of DPD or nonlinear device in the case of analog predistortion and counteracts the nonlinear characteristic of the PA. Some excellent overviews on DPD can be found in [1]-[4]. Let us now look at the challenges that DPD linearization has faced and will continue to face in the near future with 5G new radio (5G-NR).This work has been supported in part by the Spanish Government and FEDER under MICINN projects TEC2017-83343-C4-1-R and TEC2017-83343-C4-2-R and by the Generalitat de Catalunya under Grant 2017 SGR 813