Current-Mode Techniques for the Implementation of Continuous- and Discrete-Time Cellular Neural Networks

This paper presents a unified, comprehensive approach to the design of continuous-time (CT) and discrete-time (DT) cellular neural networks (CNN) using CMOS current-mode analog techniques. The net input signals are currents instead of voltages as presented in previous approaches, thus avoiding the need for current-to-voltage dedicated interfaces in image processing tasks with photosensor devices. Outputs may be either currents or voltages. Cell design relies on exploitation of current mirror properties for the efficient implementation of both linear and nonlinear analog operators. These cells are simpler and easier to design than those found in previously reported CT and DT-CNN devices. Basic design issues are covered, together with discussions on the influence of nonidealities and advanced circuit design issues as well as design for manufacturability considerations associated with statistical analysis. Three prototypes have been designed for l.6-pm n-well CMOS technologies. One is discrete-time and can be reconfigured via local logic for noise removal, feature extraction (borders and edges), shadow detection, hole filling, and connected component detection (CCD) on a rectangular grid with unity neighborhood radius. The other two prototypes are continuous-time and fixed template: one for CCD and other for noise removal. Experimental results are given illustrating performance of these prototypes

CMOS analog map decoder for (8,4) hamming code

Journal ArticleAbstract-Design and test results for a fully integrated translinear tail-biting MAP error-control decoder are presented. Decoder designs have been reported for various applications which make use of analog computation, mostly for Viterbi-style decoders. MAP decoders are more complex, and are necessary components of powerful iterative decoding systems such as Turbo codes. Analog circuits may require less area and power than digital implementations in high-speed iterative applications. Our (8, 4) Hamming decoder, implemented in an AMI 0.5- m process, is the first functioning CMOS analog MAP decoder. While designed to operate in subthreshold, the decoder also functions above threshold with a small performance penalty. The chip has been tested at bit rates up to 2 Mb/s, and simulations indicate a top speed of about 10 Mb/s in strong inversion. The decoder circuit size is 0.82 mm2, and typical power consumption is 1 mW at 1 Mb/s

CMOS design of chaotic oscillators using state variables: a monolithic Chua's circuit

This paper presents design considerations for monolithic implementation of piecewise-linear (PWL) dynamic systems in CMOS technology. Starting from a review of available CMOS circuit primitives and their respective merits and drawbacks, the paper proposes a synthesis approach for PWL dynamic systems, based on state-variable methods, and identifies the associated analog operators. The GmC approach, combining quasi-linear VCCS's, PWL VCCS's, and capacitors is then explored regarding the implementation of these operators. CMOS basic building blocks for the realization of the quasi-linear VCCS's and PWL VCCS's are presented and applied to design a Chua's circuit IC. The influence of GmC parasitics on the performance of dynamic PWL systems is illustrated through this example. Measured chaotic attractors from a Chua's circuit prototype are given. The prototype has been fabricated in a 2.4- mu m double-poly n-well CMOS technology, and occupies 0.35 mm/sup 2/, with a power consumption of 1.6 mW for a +or-2.5-V symmetric supply. Measurements show bifurcation toward a double-scroll Chua's attractor by changing a bias current

Ultra low power circuits for a miniature apnoea detection device

Imperial Users onl

Low Power Adaptive Circuits: An Adaptive Log Domain Filter and A Low Power Temperature Insensitive Oscillator Applied in Smart Dust Radio

This dissertation focuses on exploring two low power adaptive circuits. One is an adaptive filter at audio frequency for system identification. The other is a temperature insensitive oscillator for low power radio frequency communication. The adaptive filter is presented with integrated learning rules for model reference estimation. The system is a first order low pass filter with two parameters: gain and cut-off frequency. It is implemented using multiple input floating gate transistors to realize online learning of system parameters. Adaptive dynamical system theory is used to derive robust control laws in a system identification task. Simulation results show that convergence is slower using simplified control laws but still occurs within milliseconds. Experimental results confirm that the estimated gain and cut-off frequency track the corresponding parameters of the reference filter. During operation, deterministic errors are introduced by mismatch within the analog circuit implementation. An analysis is presented which attributes the errors to current mirror mismatch. The harmonic distortion of the filter operating in different inversion is analyzed using EKV model numerically. The temperature insensitive oscillator is designed for a low power wireless network. The system is based on a current starved ring oscillator implemented using CMOS transistors instead of LC tank for less chip area and power consumption. The frequency variance with temperature is compensated by the temperature adaptive circuits. Experimental results show that the frequency stability from 5°C to 65°C has been improved 10 times with automatic compensation and at least 1 order less power is consumed than published competitors. This oscillator is applied in a 2.2GHz OOK transmitter and a 2.2GHz phase locked loop based FM receiver. With the increasing needs of compact antenna, possible high data rate and wide unused frequency range of short distance communication, a higher frequency phase locked loop used for BFSK receiver is explored using an LC oscillator for its capability at 20GHz. The success of frequency demodulation is demonstrated in the simulation results that the PLL can lock in 0.5μs with 35MHz lock-in range and 2MHz detection resolution. The model of a phase locked loop used for BFSK receiver is analyzed using Matlab

Very large time constant Gm-C Filters

In this study a set of tools for the design of fully integrated transconductor-capacitor (Gm-C) filters, with very large time constants and current consumption under one micro-Ampere are presented. The selected application is a 2nd order bandpass-filter-amplifier, with a gain of 400 from 0.5 to 7Hz, carrying out the signal conditioning of a piezoelectric accelerometer which is part of an implantable cardiac pacemaker. The main challenge is to achieve very large time constants, without using any discrete external component. The chosen circuit technique to fulfill the requirement is series-parallel current division applied to standard symmetrical transconductors (OTAs). These circuits have demonstrated to be an excellent solution regarding their occupied area, power consumption, noise, linearity, and particularly offset. OTAs as low as 33pS -equivalent to a 30G resistor-, with up to 1V linear range, and input referred offset of a few mV, were designed, fabricated in a standard 0.8 micron CMOS technology, and tested. The application requires the series-parallel association of a large number of transistors, and the use of bias currents as low as a few pico-Amperes, which is not very common in analog integrated circuits. In this case the designer should employ maximum care in the selection of the transistor models to be used. A central aspect of this thesis was also to evaluate and develop noise and offset estimation models which was not obvious in the very beginning of the research. In the first two chapters an introduction to the target application is presented, and several MOS transistor characteristics in terms of the inversion coefficient -using the ACM transistor model- are evaluated. In chapter 3 it is discussed whether the usual flicker and thermal noise models are consistent regarding series-parallel association, and adequately represent the expected noise behavior under different bias conditions. A consistent, physics-based, one-equation-all-regions model for flicker noise in the MOS transistor is then presented. Several noise measurements are included demonstrating that the new model accurately fits widely different bias situations. A new model for mismatch offset in MOS transistors is presented, as a corollary of the flicker noise analysis. Finally, the correlation between flicker noise and mismatch offset, that can be seen as a DC noise, is shown. In chapter 4, the design of OTAs with an extended linear range, and very low transconductance, using series-parallel current division is presented. Precise tools are introduced for the estimation of noise and mismatch offset in series-parallel current mirrors, that are shown to help in the reduction of inaccuracies in the copy of currents with a large copy factor. The design and measurement of several OTA examples are presented. In chapter 5, the developed tools, and the OTAs shown, are employed in the design of the above mentioned filter for the piezoelectric accelerometer. A general methodology for the design of Gm-C filters with similar characteristics is established. The filter was fabricated and tested, successfully operating with a total power consumption of 233nA, up to a 2V power supply, with an input noise and mismatch offset of 2-4 Vrms, and 18 V respectively. To summarize the main results obtained were: The development of a new flicker noise model, the study of the effect of mismatch regarding series-parallel association, a new design methodology for OTAs and Gm-C filters. It is our hope that this constitutes a helpful set of tools for the circuit designer.En esta tesis se presenta un conjunto de herramientas para el diseño de circuitos integrados que implementan filtros transconductor-capacitor (Gm-C), de muy altas constantes de tiempo, con bajo ruido, y consumo de corriente por debajo del micro-Ampere. Como ejemplo de aplicación se toma un amplificador-pasabanda 2º orden, de ganancia 400 en la banda de 0.5 a 7Hz, que realiza el acondicionamiento de señal de un acelerómetro piezoeléctrico a ser empleado en un marcapasos implantable. El principal desafío es realizar en dicho filtro de tiempo continuo, muy altas constantes de tiempo sin usar componentes externos. La técnica elegida para alcanzar tal objetivo es la división serie-paralelo de corriente en transconductores (OTAs) simétricos estándar. Estos circuitos demostraron ser una excelente solución en cuanto al área ocupada, su consumo, ruido, linealidad, y en particular offset. Se diseñaron, fabricaron, y midieron, OTAs hasta 33pS -equivalente a una resistencia de 30G -, con hasta 1V de rango de lineal, y offset a la entrada de algunos mV, utilizando una tecnología CMOS de 0.8 micras de largo mínimo de canal. La aplicación requiere la asociación serie-paralelo de un gran número de transistores, y polarización con corrientes de hasta pico-Amperes, lo que constituye una situación poco frecuente en circuitos integrados analógicos. En este marco el diseñador debe elegir los modelos de transistor con sumo cuidado. Un aspecto central de esta tesis es también, el estudio y presentación de modelos adecuados de ruido y offset, que no resultan obvios al principio. En los primeros dos capítulos se realiza una introducción y se revisa, utilizando el modelo ACM, diferentes características del transistor MOS en función del nivel de inversión. En el capítulo 3 revisa la pertinencia y consistencia frente a la asociación serie-paralelo, de los modelos usuales de ruido de flicker o 1/f, y térmico. Luego se presenta, incluyendo medidas, un nuevo modelo físico, consistente, simple, y válido en todas las regiones de operación del transistor MOS, para el ruido de flicker. Como corolario a este estudio se presenta un nuevo modelo para estimar el desapareo entre transistores, en función no solo de la geometría, pero también de la polarización. Se demuestra la correlación, debido a su origen físico análogo, entre el ruido de flicker y el offset por desapareo que puede ser visto como un ruido en DC. En el capítulo 4 se presenta el diseño de OTAs con rango de linealidad extendido, y muy baja transconductancia, utilizando división serie-paralelo de corriente. Se presentan herramientas precisas para la estimación de offset y ruido y se demuestra la utilidad de la técnica para reducir el offset en espejos de corriente. Se presenta el diseño y medida de diversos OTAs. En el capítulo 5, las herramientas desarrolladas, y los OTAs presentados, son empleados en el diseño del filtro descripto para un acelerómetro piezoeléctrico. Se establece una metodología general para el diseño de filtros Gm-C con características similares. El filtro se fabricó y midió, operando en forma satisfactoria, con un consumo total de 230nA y hasta los 2V de tensión de alimentación, con ruido y offset a la entrada de tan solo 2-4 Vrms, y 18 V respectivamente. El desarrollo de un nuevo modelo de ruido 1/f para el transistor MOS, el estudio de la influencia del offset frente a la asociación serie-paralelo y su aplicación en OTAs, la metodología de diseño empleada, la demostración del uso de técnicas novedosas en una aplicación como la elegida que tiene relevancia tecnológica e interés académico; esperamos que todo ello constituya una contribución valiosa para la comunidad científica en microelectrónica y un conjunto de herramientas de utilidad para el diseño de circuitos

RF Circuit linearity optimization using a general weak nonlinearity model

This paper focuses on optimizing the linearity in known RF circuits, by exploring the circuit design space that is usually available in today’s deep submicron CMOS technologies. Instead of using brute force numerical optimizers we apply a generalized weak nonlinearity model that only involves AC transfer functions to derive simple equations for obtaining design insights. The generalized weak nonlinearity model is applied to three known RF circuits: a cascode common source amplifier, a common gate LNA and a CMOS attenuator. It is shown that in deep submicron CMOS technologies the cascode transistor in both the common source amplifier and in the common gate amplifier significantly contributes IM3 distortion. Some design insights are presented for reducing the cascode transistor related distortion, among which moderate inversion biasing that improves IIP3 by 10 dB up to 5 GHz in a 90 nm CMOS process. For the attenuator, a wideband IM3 cancellation technique is introduced and demonstrated using simulations

Ultra-Low-Voltage IC Design Methods

The emerging nanoscale technologies inherently offer transistors working with low voltage levels and are optimized for low-power operation. However, these technologies lack quality electronic components vital for reliable analog and/or mixed-signal design (e.g., resistor, capacitor, etc.) as they are predominantly used in high-performance digital designs. Moreover, the voltage headroom, ESD properties, the maximum current densities, parasitic effects, process fluctuations, aging effects, and many other parameters are superior in verified-by-time CMOS processes using planar transistors. This is the main reason, why low-voltage, low-power high-performance analog and mixed-signal circuits are still being designed in mature process nodes. In the proposed chapter, we bring an overview of main challenges and design techniques effectively applicable for ultra-low-voltage and low-power analog integrated circuits in nanoscale technologies. New design challenges and limitations linked with a low value of the supply voltage, the process fluctuation, device mismatch, and other effects are discussed. In the later part of the chapter, conventional and unconventional design techniques (bulk-driven approach, floating-gate, dynamic threshold, etc.) to design analog integrated circuits towards ultra-low-voltage systems and applications are described. Examples of ultra-low-voltage analog ICs blocks (an operational amplifier, a voltage comparator, a charge pump, etc.) designed in a standard CMOS technology using the unconventional design approach are presented