A configurable vector processor for accelerating speech coding algorithms

The growing demand for voice-over-packer (VoIP) services and multimedia-rich applications has made increasingly important the efficient, real-time implementation of low-bit rates speech coders on embedded VLSI platforms. Such speech coders are designed to substantially reduce the bandwidth requirements thus enabling dense multichannel gateways in small form factor. This however comes at a high computational cost which mandates the use of very high performance embedded processors. This thesis investigates the potential acceleration of two major ITU-T speech coding algorithms, namely G.729A and G.723.1, through their efficient implementation on a configurable extensible vector embedded CPU architecture. New scalar and vector ISAs were introduced which resulted in up to 80% reduction in the dynamic instruction count of both workloads. These instructions were subsequently encapsulated into a parametric, hybrid SISD (scalar processor)–SIMD (vector) processor. This work presents the research and implementation of the vector datapath of this vector coprocessor which is tightly-coupled to a Sparc-V8 compliant CPU, the optimization and simulation methodologies employed and the use of Electronic System Level (ESL) techniques to rapidly design SIMD datapaths

New strategies for low noise, agile PLL frequency synthesis

Phase-Locked Loop based frequency synthesis is an essential technique employed in wireless communication systems for local oscillator generation. The ultimate goal in any design of frequency synthesisers is to generate precise and stable output frequencies with fast switching and minimal spurious and phase noise. The conflict between high resolution and fast switching leads to two separate integer synthesisers to satisfy critical system requirements. This thesis concerns a new sigma-delta fractional-N synthesiser design which is able to be directly modulated at high data rates while simultaneously achieving good noise performance. Measured results from a prototype indicate that fast switching, low noise and spurious free spectra are achieved for most covered frequencies. The phase noise of the unmodulated synthesiser was measured −113 dBc/Hz at 100 kHz offset from the carrier. The intermodulation effect in synthesisers is capable of producing a family of spurious components of identical form to fractional spurs caused in quantisation process. This effect directly introduces high spurs on some channels of the synthesiser output. Numerical and analytic results describing this effect are presented and amplitude and distribution of the resulting fractional spurs are predicted and validated against simulated and measured results. Finally an experimental arrangement, based on a phase compensation technique, is presented demonstrating significant suppression of intermodulation-borne spurs. A new technique, pre-distortion noise shaping, is proposed to dramatically reduce the impact of fractional spurs in fractional-N synthesisers. The key innovation is the introduction in the bitstream generation process of carefully-chosen set of components at identical offset frequencies and amplitudes and in anti-phase with the principal fractional spurs. These signals are used to modify the Σ-Δ noise shaping, so that fractional spurs are effectively cancelled. This approach can be highly effective in improving spectral purity and reduction of spurious components caused by the Σ-Δ modulator, quantisation noise, intermodulation effects and any other circuit factors. The spur cancellation is achieved in the digital part of the synthesiser without introducing additional circuitry. This technique has been convincingly demonstrated by simulated and experimental results

On detection of OFDM signals for cognitive radio applications

As the requirement for wireless telecommunications services continues to grow, it has become increasingly important to ensure that the Radio Frequency (RF) spectrum is managed efficiently. As a result of the current spectrum allocation policy, it has been found that portions of RF spectrum belonging to licensed users are often severely underutilised, at particular times and geographical locations. Awareness of this problem has led to the development of Dynamic Spectrum Access (DSA) and Cognitive Radio (CR) as possible solutions. In one variation of the shared-use model for DSA, it is proposed that the inefficient use of licensed spectrum could be overcome by enabling unlicensed users to opportunistically access the spectrum when the licensed user is not transmitting. In order for an unlicensed device to make decisions, it must be aware of its own RF environment and, therefore, it has been proposed that DSA could been abled using CR. One approach that has be identified to allow the CR to gain information about its operating environment is spectrum sensing. An interesting solution that has been identified for spectrum sensing is cyclostationary detection. This property refers to the inherent periodic nature of the second order statistics of many communications signals. One of the most common modulation formats in use today is Orthogonal Frequency Division Multiplexing (OFDM), which exhibits cyclostationarity due to the addition of a Cyclic Prefix (CP). This thesis examines several statistical tests for cyclostationarity in OFDM signals that may be used for spectrum sensing in DSA and CR. In particular, focus is placed on statistical tests that rely on estimation of the Cyclic Autocorrelation Function (CAF). Based on splitting the CAF into two complex component functions, several new statistical tests are introduced and are shown to lead to an improvement in detection performance when compared to the existing algorithms. The performance of each new algorithm is assessed in Additive White Gaussian Noise (AWGN), impulsive noise and when subjected to impairments such as multipath fading and Carrier Frequency Offset (CFO). Finally, each algorithm is targeted for Field Programmable Gate Array (FPGA) implementation using a Xilinx 7 series device. In order to keep resource costs to a minimum, it is suggested that the new algorithms are implemented on the FPGA using hardware sharing, and a simple mathematical re-arrangement of certain tests statistics is proposed to circumvent a costly division operation.As the requirement for wireless telecommunications services continues to grow, it has become increasingly important to ensure that the Radio Frequency (RF) spectrum is managed efficiently. As a result of the current spectrum allocation policy, it has been found that portions of RF spectrum belonging to licensed users are often severely underutilised, at particular times and geographical locations. Awareness of this problem has led to the development of Dynamic Spectrum Access (DSA) and Cognitive Radio (CR) as possible solutions. In one variation of the shared-use model for DSA, it is proposed that the inefficient use of licensed spectrum could be overcome by enabling unlicensed users to opportunistically access the spectrum when the licensed user is not transmitting. In order for an unlicensed device to make decisions, it must be aware of its own RF environment and, therefore, it has been proposed that DSA could been abled using CR. One approach that has be identified to allow the CR to gain information about its operating environment is spectrum sensing. An interesting solution that has been identified for spectrum sensing is cyclostationary detection. This property refers to the inherent periodic nature of the second order statistics of many communications signals. One of the most common modulation formats in use today is Orthogonal Frequency Division Multiplexing (OFDM), which exhibits cyclostationarity due to the addition of a Cyclic Prefix (CP). This thesis examines several statistical tests for cyclostationarity in OFDM signals that may be used for spectrum sensing in DSA and CR. In particular, focus is placed on statistical tests that rely on estimation of the Cyclic Autocorrelation Function (CAF). Based on splitting the CAF into two complex component functions, several new statistical tests are introduced and are shown to lead to an improvement in detection performance when compared to the existing algorithms. The performance of each new algorithm is assessed in Additive White Gaussian Noise (AWGN), impulsive noise and when subjected to impairments such as multipath fading and Carrier Frequency Offset (CFO). Finally, each algorithm is targeted for Field Programmable Gate Array (FPGA) implementation using a Xilinx 7 series device. In order to keep resource costs to a minimum, it is suggested that the new algorithms are implemented on the FPGA using hardware sharing, and a simple mathematical re-arrangement of certain tests statistics is proposed to circumvent a costly division operation

A CMOS Fractional Frequency Synthesizer for a Fully Integrated S-Band Extravehicular Activity (EVA) Radio Transceiver

Extravehicular activity (EVA) is an important aspect of space explorations. It enables astronauts carry out tasks outside the protective environment of the spacecraft cabin. The crew requires EVA radio transceivers to transmit and receive information among themselves and with equipment in space. Communication is done through the S frequency band (2GHz to 4GHz). Since the EVA radio transceiver is part of the space suits the astronauts wear for EVA, it is important that lightweight, low power consumption and miniaturized systems are utilized in their design and implementation. This thesis presents the design and implementation of a fully integrated frequency synthesizer for carrier signal generation in the EVA radio transceiver. The transceiver consists of a dual up-conversion transmitter (TX) and a direct conversion receiver (RX) at 2.4GHz. It supports 10 channels spaced at 6MHz for both video and voice communications, covering the frequency band from 2.4GHz to 2.454GHz. Therefore in the TX mode, the frequencies required are 0.8GHz to 0.818GHz (quadrature) and 1.6GHz to 1.636GHz (differential) for dual up-conversion to prevent the pulling problem between the power amplifier (PA) and voltage controlled oscillator (VCO) of the synthesizer. In RX mode, the frequencies from 4.8GHz to 4.908GHz are synthesized with a divide-by-two circuit to generate quadrature signals of 2.4GHz to 2.454GHz. In order to cover the frequency ranges in both TX and RX modes with a small area and low power consumption, a dual-band VCO fractional-N PLL is implemented. The dual-path loop filter topology is utilized to further reduce chip area. The fractional synthesizer is fabricated in 0.18μm CMOS technology and has a loop bandwidth of around 40kHz. It occupies a relatively small area of 1.54mm^(2) and consumes a low power of 22.68mW with a 1 V supply for the VCO and 1.8V supply for the rest of the blocks. The synthesizer achieves a reference spur performance of less than –62.34dBc for the lower band (LB) and less than –68.36dBc for the higher band (HB). The phase noise at 1MHz for the LB ranges from -125.38 to -130.39 dBc/Hz and for the HB -113.12 to -120.16 dBc/Hz. Thus the synthesizer achieves low power consumption with good spectral purity while occupying a small chip area making it suitable for EVA radio applications

Time and frequency domain algorithms for speech coding

The promise of digital hardware economies (due to recent advances in VLSI technology), has focussed much attention on more complex and sophisticated speech coding algorithms which offer improved quality at relatively low bit rates. This thesis describes the results (obtained from computer simulations) of research into various efficient (time and frequency domain) speech encoders operating at a transmission bit rate of 16 Kbps. In the time domain, Adaptive Differential Pulse Code Modulation (ADPCM) systems employing both forward and backward adaptive prediction were examined. A number of algorithms were proposed and evaluated, including several variants of the Stochastic Approximation Predictor (SAP). A Backward Block Adaptive (BBA) predictor was also developed and found to outperform the conventional stochastic methods, even though its complexity in terms of signal processing requirements is lower. A simplified Adaptive Predictive Coder (APC) employing a single tap pitch predictor considered next provided a slight improvement in performance over ADPCM, but with rather greater complexity. The ultimate test of any speech coding system is the perceptual performance of the received speech. Recent research has indicated that this may be enhanced by suitable control of the noise spectrum according to the theory of auditory masking. Various noise shaping ADPCM configurations were examined, and it was demonstrated that a proposed pre-/post-filtering arrangement which exploits advantageously the predictor-quantizer interaction, leads to the best subjective performance in both forward and backward prediction systems. Adaptive quantization is instrumental to the performance of ADPCM systems. Both the forward adaptive quantizer (AQF) and the backward oneword memory adaptation (AQJ) were examined. In addition, a novel method of decreasing quantization noise in ADPCM-AQJ coders, which involves the application of correction to the decoded speech samples, provided reduced output noise across the spectrum, with considerable high frequency noise suppression. More powerful (and inevitably more complex) frequency domain speech coders such as the Adaptive Transform Coder (ATC) and the Sub-band Coder (SBC) offer good quality speech at 16 Kbps. To reduce complexity and coding delay, whilst retaining the advantage of sub-band coding, a novel transform based split-band coder (TSBC) was developed and found to compare closely in performance with the SBC. To prevent the heavy side information requirement associated with a large number of bands in split-band coding schemes from impairing coding accuracy, without forgoing the efficiency provided by adaptive bit allocation, a method employing AQJs to code the sub-band signals together with vector quantization of the bit allocation patterns was also proposed. Finally, 'pipeline' methods of bit allocation and step size estimation (using the Fast Fourier Transform (FFT) on the input signal) were examined. Such methods, although less accurate, are nevertheless useful in limiting coding delay associated with SRC schemes employing Quadrature Mirror Filters (QMF)

Real-Time Narrowband and Wideband Beamforming Techniques for Fully-Digital RF Arrays

Elemental digital beamforming offers increased flexibility for multi-function radio frequency (RF) systems supporting radar and communications applications. As fully digital arrays, components, and subsystems are becoming more affordable in the military and commercial industries, analog components such as phase shifters, filters, and mixers have begun to be replaced by digital circuits which presents efficiency challenges in power constrained scenarios. Furthermore, multi-function radar and communications systems are exploiting the multiple simultaneous beam capability provided by digital at every element beamforming. Along with further increasing data samples rates and increasing instantaneous bandwidths (IBW), real time processing in the digital domain has become a challenge due to the amount of data produced and processed in current systems. These arrays generate hundreds of gigabits per second of data throughput or more which is costly to send off-chip to an adjunct processor fundamentally limiting the overall performance of an RF array system. In this dissertation, digital filtering techniques and architectures are described which calibrate and beamform both narrowband and wideband RF arrays on receive. The techniques are shown to optimize one or many parameters of the digital transceiver system to improve the overall system efficiency. Digitally beamforming in the beamspace is shown to further increase the processing efficiency of an adaptive system compared to state of the art frequency domain approaches by minimizing major processing bottlenecks of generating adaptive filter coefficients. The techniques discussed are compared and contrasted across different hardware processor modules including field-programmable gate arrays (FPGAs), graphical processing units (GPUs), and central processing units (CPUs)

Architecture and algorithms for the implementation of digital wireless receivers in FPGA and ASIC: ISDB-T and DVB-S2 cases

[EN] The first generation of Terrestrial Digital Television(DTV) has been in service for over a decade. In 2013, several countries have already completed the transition from Analog to Digital TV Broadcasting, most of which in Europe. In South America, after several studies and trials, Brazil adopted the Japanese standard with some innovations. Japan and Brazil started Digital Terrestrial Television Broadcasting (DTTB) services in December 2003 and December 2007 respectively, using Integrated Services Digital Broadcasting - Terrestrial (ISDB-T), also known as ARIB STD-B31. In June 2005 the Committee for the Information Technology Area (CATI) of Brazilian Ministry of Science and Technology and Innovation MCTI approved the incorporation of the IC-Brazil Program, in the National Program for Microelectronics (PNM) . The main goals of IC-Brazil are the formal qualification of IC designers, support to the creation of semiconductors companies focused on projects of ICs within Brazil, and the attraction of semiconductors companies focused on the design and development of ICs in Brazil. The work presented in this thesis originated from the unique momentum created by the combination of the birth of Digital Television in Brazil and the creation of the IC-Brazil Program by the Brazilian government. Without this combination it would not have been possible to make these kind of projects in Brazil. These projects have been a long and costly journey, albeit scientifically and technologically worthy, towards a Brazilian DTV state-of-the-art low complexity Integrated Circuit, with good economy scale perspectives, due to the fact that at the beginning of this project ISDB-T standard was not adopted by several countries like DVB-T. During the development of the ISDB-T receiver proposed in this thesis, it was realized that due to the continental dimensions of Brazil, the DTTB would not be enough to cover the entire country with open DTV signal, specially for the case of remote localizations far from the high urban density regions. Then, Eldorado Research Institute and Idea! Electronic Systems, foresaw that, in a near future, there would be an open distribution system for high definition DTV over satellite, in Brazil. Based on that, it was decided by Eldorado Research Institute, that would be necessary to create a new ASIC for broadcast satellite reception. At that time DVB-S2 standard was the strongest candidate for that, and this assumption still stands nowadays. Therefore, it was decided to apply to a new round of resources funding from the MCTI - that was granted - in order to start the new project. This thesis discusses in details the Architecture and Algorithms proposed for the implementation of a low complexity Intermediate Frequency(IF) ISDB-T Receiver on Application Specific Integrated Circuit (ASIC) CMOS. The Architecture proposed here is highly based on the COordinate Rotation Digital Computer (CORDIC) Algorithm, that is a simple and efficient algorithm suitable for VLSI implementations. The receiver copes with the impairments inherent to wireless channels transmission and the receiver crystals. The thesis also discusses the Methodology adopted and presents the implementation results. The receiver performance is presented and compared to those obtained by means of simulations. Furthermore, the thesis also presents the Architecture and Algorithms for a DVB-S2 receiver targeting its ASIC implementation. However, unlike the ISDB-T receiver, only preliminary ASIC implementation results are introduced. This was mainly done in order to have an early estimation of die area to prove that the project in ASIC is economically viable, as well as to verify possible bugs in early stage. As in the case of ISDB-T receiver, this receiver is highly based on CORDIC algorithm and it was prototyped in FPGA. The Methodology used for the second receiver is derived from that used for the ISDB-T receiver, with minor additions given the project characteristics.[ES] La primera generación de Televisión Digital Terrestre(DTV) ha estado en servicio por más de una década. En 2013, varios países completaron la transición de transmisión analógica a televisión digital, la mayoría de ellas en Europa. En América del Sur, después de varios estudios y ensayos, Brasil adoptó el estándar japonés con algunas innovaciones. Japón y Brasil comenzaron a prestar el servicio de Difusión de Televisión Digital Terrestre (DTTB) en diciembre de 2003 y diciembre de 2007 respectivamente, utilizando Radiodifusión Digital de Servicios Integrados Terrestres (ISDB-T), también conocida como ARIB STD-B31. En junio de 2005, el Comité del Área de Tecnología de la Información (CATI) del Ministerio de Ciencia, Tecnología e Innovación de Brasil - MCTI aprobó la incorporación del Programa CI-Brasil, en el Programa Nacional de Microelectrónica (PNM). Los principales objetivos de la CI-Brasil son la formación de diseñadores de CIs, apoyar la creación de empresas de semiconductores enfocadas en proyectos de circuitos integrados dentro de Brasil, y la atracción de empresas de semiconductores interesadas en el diseño y desarrollo de circuitos integrados. El trabajo presentado en esta tesis se originó en el impulso único creado por la combinación del nacimiento de la televisión digital en Brasil y la creación del Programa de CI-Brasil por el gobierno brasileño. Sin esta combinación no hubiera sido posible realizar este tipo de proyectos en Brasil. Estos proyectos han sido un trayecto largo y costoso, aunque meritorio desde el punto de vista científico y tecnológico, hacia un Circuito Integrado brasileño de punta y de baja complejidad para DTV, con buenas perspectivas de economía de escala debido al hecho que al inicio de este proyecto, el estándar ISDB-T no fue adoptado por varios países como DVB-T. Durante el desarrollo del receptor ISDB-T propuesto en esta tesis, se observó que debido a las dimensiones continentales de Brasil, la DTTB no sería suficiente para cubrir todo el país con la señal de televisión digital abierta, especialmente para el caso de localizaciones remotas, apartadas de las regiones de alta densidad urbana. En ese momento, el Instituto de Investigación Eldorado e Idea! Sistemas Electrónicos, previeron que en un futuro cercano habría un sistema de distribución abierto para DTV de alta definición por satélite en Brasil. Con base en eso, el Instituto de Investigación Eldorado decidió que sería necesario crear un nuevo ASIC para la recepción de radiodifusión por satélite, basada el estándar DVB-S2. En esta tesis se analiza en detalle la Arquitectura y algoritmos propuestos para la implementación de un receptor ISDB-T de baja complejidad y frecuencia intermedia (IF) en un Circuito Integrado de Aplicación Específica (ASIC) CMOS. La arquitectura aquí propuesta se basa fuertemente en el algoritmo Computadora Digital para Rotación de Coordenadas (CORDIC), el cual es un algoritmo simple, eficiente y adecuado para implementaciones VLSI. El receptor hace frente a las deficiencias inherentes a las transmisiones por canales inalámbricos y los cristales del receptor. La tesis también analiza la metodología adoptada y presenta los resultados de la implementación. Por otro lado, la tesis también presenta la arquitectura y los algoritmos para un receptor DVB-S2 dirigido a la implementación en ASIC. Sin embargo, a diferencia del receptor ISDB-T, se introducen sólo los resultados preliminares de implementación en ASIC. Esto se hizo principalmente con el fin de tener una estimación temprana del área del die para demostrar que el proyecto en ASIC es económicamente viable, así como para verificar posibles errores en etapa temprana. Como en el caso de receptor ISDB-T, este receptor se basa fuertemente en el algoritmo CORDIC y fue un prototipado en FPGA. La metodología utilizada para el segundo receptor se deriva de la utilizada para el re[CA] La primera generació de Televisió Digital Terrestre (TDT) ha estat en servici durant més d'una dècada. En 2013, diversos països ja van completar la transició de la radiodifusió de televisió analògica a la digital, i la majoria van ser a Europa. A Amèrica del Sud, després de diversos estudis i assajos, Brasil va adoptar l'estàndard japonés amb algunes innovacions. Japó i Brasil van començar els servicis de Radiodifusió de Televisió Terrestre Digital (DTTB) al desembre de 2003 i al desembre de 2007, respectivament, utilitzant la Radiodifusió Digital amb Servicis Integrats de (ISDB-T), coneguda com a ARIB STD-B31. Al juny de 2005, el Comité de l'Àrea de Tecnologia de la Informació (CATI) del Ministeri de Ciència i Tecnologia i Innovació del Brasil (MCTI) va aprovar la incorporació del programa CI Brasil al Programa Nacional de Microelectrònica (PNM). Els principals objectius de CI Brasil són la qualificació formal dels dissenyadors de circuits integrats, el suport a la creació d'empreses de semiconductors centrades en projectes de circuits integrats dins del Brasil i l'atracció d'empreses de semiconductors centrades en el disseny i desenvolupament de circuits integrats. El treball presentat en esta tesi es va originar en l'impuls únic creat per la combinació del naixement de la televisió digital al Brasil i la creació del programa Brasil CI pel govern brasiler. Sense esta combinació no hauria estat possible realitzar este tipus de projectes a Brasil. Estos projectes han suposat un viatge llarg i costós, tot i que digne científicament i tecnològica, cap a un circuit integrat punter de baixa complexitat per a la TDT brasilera, amb bones perspectives d'economia d'escala perquè a l'inici d'este projecte l'estàndard ISDB-T no va ser adoptat per diversos països, com el DVB-T. Durant el desenvolupament del receptor de ISDB-T proposat en esta tesi, va resultar que, a causa de les dimensions continentals de Brasil, la DTTB no seria suficient per cobrir tot el país amb el senyal de TDT oberta, especialment pel que fa a les localitzacions remotes allunyades de les regions d'alta densitat urbana.. En este moment, l'Institut de Recerca Eldorado i Idea! Sistemes Electrònics van preveure que, en un futur pròxim, no hi hauria a Brasil un sistema de distribució oberta de TDT d'alta definició a través de satèl¿lit. D'acord amb això, l'Institut de Recerca Eldorado va decidir que seria necessari crear un nou ASIC per a la recepció de radiodifusió per satèl¿lit. basat en l'estàndard DVB-S2. En esta tesi s'analitza en detall l'arquitectura i els algorismes proposats per l'execució d'un receptor ISDB-T de Freqüència Intermèdia (FI) de baixa complexitat sobre CMOS de Circuit Integrat d'Aplicacions Específiques (ASIC). L'arquitectura ací proposada es basa molt en l'algorisme de l'Ordinador Digital de Rotació de Coordenades (CORDIC), que és un algorisme simple i eficient adequat per implementacions VLSI. El receptor fa front a les deficiències inherents a la transmissió de canals sense fil i els cristalls del receptor. Esta tesi també analitza la metodologia adoptada i presenta els resultats de l'execució. Es presenta el rendiment del receptor i es compara amb els obtinguts per mitjà de simulacions. D'altra banda, esta tesi també presenta l'arquitectura i els algorismes d'un receptor de DVB-S2 de cara a la seua implementació en ASIC. No obstant això, a diferència del receptor ISDB-T, només s'introdueixen resultats preliminars d'implementació en ASIC. Això es va fer principalment amb la finalitat de tenir una estimació primerenca de la zona de dau per demostrar que el projecte en ASIC és econòmicament viable, així com per verificar possibles errors en l'etapa primerenca. Com en el cas del receptor ISDB-T, este receptor es basa molt en l'algorisme CORDIC i va ser un prototip de FPGA. La metodologia utilitzada per al segon receptor es deriva de la utilitzada per al receptor IRodrigues De Lima, E. (2016). Architecture and algorithms for the implementation of digital wireless receivers in FPGA and ASIC: ISDB-T and DVB-S2 cases [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/61967TESI

Circuit paradigm in the 21

reviewe

The 1992 4th NASA SERC Symposium on VLSI Design

Papers from the fourth annual NASA Symposium on VLSI Design, co-sponsored by the IEEE, are presented. Each year this symposium is organized by the NASA Space Engineering Research Center (SERC) at the University of Idaho and is held in conjunction with a quarterly meeting of the NASA Data System Technology Working Group (DSTWG). One task of the DSTWG is to develop new electronic technologies that will meet next generation electronic data system needs. The symposium provides insights into developments in VLSI and digital systems which can be used to increase data systems performance. The NASA SERC is proud to offer, at its fourth symposium on VLSI design, presentations by an outstanding set of individuals from national laboratories, the electronics industry, and universities. These speakers share insights into next generation advances that will serve as a basis for future VLSI design