A Novel Power Analysis Attack Resilient Adiabatic Logic without Charge Sharing

In this paper, we propose a novel power analysis attack resilient adiabatic logic which, unlike existing secure adiabatic logic designs doesn’t require any charge sharing between the output nodes of the gates. The proposed logic also removes the non-adiabatic losses (NAL) during the evaluation phase of the power-clock. We investigate and compare our proposed and the existing secure adiabatic logic across a range of “power-clock” frequencies on the basis of percentage Normalized Energy Deviation (%NED), percentage Normalized Standard Deviation(%NSD) and average energy dissipation. The pre-layout and post-layout simulation results show that our proposed logic exhibits the least value of %NED and %NSD in comparison to the existing secure adiabatic logic designs at the frequency ranging from 1MHz to 100MHz. Also, our proposed logic consumes the lowest energy

Robustness of Power Analysis Attack Resilient Adiabatic Logic: WCS-QuAL under PVT Variations

In this paper, we propose Without Charge Sharing Quasi Adiabatic Logic (WCS-QuAL) as a countermeasure against Power Analysis Attacks. We evaluate and compare our logic with the recently proposed secure adiabatic logic designs SPGAL and EE-SPFAL at frequencies ranging from 1MHz to 100MHz. Simulation results show that WCS-QuAL outperforms the existing secure adiabatic logic designs on the basis of % Normalized Energy Deviation (NED) and % Normalized Standard Deviation (NSD) at all simulated frequencies. Also, all 2-input gates using WCS-QuAL dissipate nearly equal energy for all possible input transitions. In addition, the energy dissipated by WCS-QuAL approaches to the energy dissipation of EESPFAL and SPGAL as the output load capacitance is increased above 100fF. To further evaluate and compare the performance, GF (24) bit-parallel multiplier was implemented as a design example. The impact of Process-Voltage-Temperature (PVT) variations, power supply scaling and technology on the performance of the three logic designs was investigated and compared. Simulation results show that WCS-QuAL passed the functionality test against PVT variations and can perform well against the power supply scaling (from 1.8V to 0.5V). It also exhibits the least value of %NED and %NSD against PVT variations and when the power supply is scaled down compared to EE-SPFAL and SPGAL. At lower technology, WCS-QuAL, shows more improvement in energy dissipation than EE-SPFAL

Symmetric Power Analysis Attack Resilient Adiabatic Logic for Smartcard Applications

On the whole existing secure adiabatic logic designs exhibit variations in current peaks and have asymmetric structures. However, asymmetric structure and variations in current peaks make the circuit vulnerable to Power Analysis Attacks (PAA). In this paper, we shall present a novel PAA resilient adiabatic logic which has a symmetric structure and exhibits the least variations in current peaks for basic gates as well as in 8-bit Montgomery multiplier. The proposed logic has been compared with two recently proposed secure adiabatic logic designs for operating frequencies ranging from 1MHz to 100MHz and power-supply scaling ranging from 0.6V to 1.8V. Simulation results of the gates show that our proposed logic exhibits the lowest Normalized Energy Deviation (NED) and Normalized Standard Deviation (NSD) under the said frequency variations. All the 2-input gates that deploy the proposed logic dissipate nearly the same average energy within 0.2% of each other at all the frequencies simulated and thus, along with the dataindependence,gate-function-independence is achieved. The paper will also report on the energy dissipated by the proposed logic which approaches that of the existing logic designs as the output load capacitance is increased above 100fF. The simulation results of the 8-bit adiabatic Montgomery multiplier show that the proposed logic exhibits the least value of NED and NSD under the said frequency variations and power-supply scaling. Finally, the paper will report on the current waveform graphs for variations in current peaks under power-clock scaling

Designing Novel Hardware Security Primitives for Smart Computing Devices

Smart computing devices are miniaturized electronics devices that can sense their surroundings, communicate, and share information autonomously with other devices to work cohesively. Smart devices have played a major role in improving quality of the life and boosting the global economy. They are ubiquitously present, smart home, smart city, smart girds, industry, healthcare, controlling the hazardous environment, and military, etc. However, we have witnessed an exponential rise in potential threat vectors and physical attacks in recent years. The conventional software-based security approaches are not suitable in the smart computing device, therefore, hardware-enabled security solutions have emerged as an attractive choice. Developing hardware security primitives, such as True Random Number Generator (TRNG) and Physically Unclonable Function (PUF) from electrical properties of the sensor could be a novel research direction. Secondly, the Lightweight Cryptographic (LWC) ciphers used in smart computing devices are found vulnerable against Correlation Power Analysis (CPA) attack. The CPA performs statistical analysis of the power consumption of the cryptographic core and reveals the encryption key. The countermeasure against CPA results in an increase in energy consumption, therefore, they are not suitable for battery operated smart computing devices. The primary goal of this dissertation is to develop novel hardware security primitives from existing sensors and energy-efficient LWC circuit implementation with CPA resilience. To achieve these. we focus on developing TRNG and PUF from existing photoresistor and photovoltaic solar cell sensors in smart devices Further, we explored energy recovery computing (also known as adiabatic computing) circuit design technique that reduces the energy consumption compared to baseline CMOS logic design and same time increasing CPA resilience in low-frequency applications, e.g. wearable fitness gadgets, hearing aid and biomedical instruments. The first contribution of this dissertation is to develop a TRNG prototype from the uncertainty present in photoresistor sensors. The existing sensor-based TRNGs suffer a low random bit generation rate, therefore, are not suitable in real-time applications. The proposed prototype has an average random bit generation rate of 8 kbps, 32 times higher than the existing sensor-based TRNG. The proposed lightweight scrambling method results in random bit entropy close to ideal value 1. The proposed TRNG prototype passes all 15 statistical tests of the National Institute of Standards and Technology (NIST) Statistical Test Suite with quality performance. The second contribution of this dissertation is to develop an integrated TRNG-PUF designed using photovoltaic solar cell sensors. The TRNG and PUF are mutually independent in the way they are designed, therefore, integrating them as one architecture can be beneficial in resource-constrained computing devices. We propose a novel histogram-based technique to segregate photovoltaic solar cell sensor response suitable for TRNG and PUF respectively. The proposed prototype archives approximately 34\% improvement in TRNG output. The proposed prototype achieves an average of 92.13\% reliability and 50.91\% uniformity performance in PUF response. The proposed sensor-based hardware security primitives do not require additional interfacing hardware. Therefore, they can be ported as a software update on existing photoresistor and photovoltaic sensor-based devices. Furthermore, the sensor-based design approach can identify physically tempered and faulty sensor nodes during authentication as their response bit differs. The third contribution is towards the development of a novel 2-phase sinusoidal clocking implementation, 2-SPGAL for existing Symmetric Pass Gate Adiabatic Logic (SPGAL). The proposed 2-SPGAL logic-based LWC cipher PRESENT shows an average of 49.34\% energy saving compared to baseline CMOS logic implementation. Furthermore, the 2-SPGAL prototype has an average of 22.76\% better energy saving compared to 2-EE-SPFAL (2-phase Energy-Efficient-Secure Positive Feedback Adiabatic Logic). The proposed 2-SPGAL was tested for energy-efficiency performance for the frequency range of 50 kHz to 250 kHz, used in healthcare gadgets and biomedical instruments. The proposed 2-SPGAL based design saves 16.78\% transistor count compared to 2-EE-SPFAL counterpart. The final contribution is to explore Clocked CMOS Adiabatic Logic (CCAL) to design a cryptographic circuit. Previously proposed 2-SPGAL and 2-EE-SPFAL uses two complementary pairs of the transistor evaluation network, thus resulting in a higher transistor count compared to the CMOS counterpart. The CCAL structure is very similar to CMOS and unlike 2-SPGAL and 2-EE-SPFAL, it does not require discharge circuitry to improve security performance. The case-study implementation LWC cipher PRESENT S-Box using CCAL results into 45.74\% and 34.88\% transistor count saving compared to 2-EE-SPFAL and 2-SPGAL counterpart. Furthermore, the case-study implementation using CCAL shows more than 95\% energy saving compared to CMOS logic at frequency range 50 kHz to 125 kHz, and approximately 60\% energy saving at frequency 250 kHz. The case study also shows 32.67\% and 11.21\% more energy saving compared to 2-EE-SPFAL and 2-SPGAL respectively at frequency 250 kHz. We also show that 200 fF of tank capacitor in the clock generator circuit results in optimum energy and security performance in CCAL

Adiabatic Circuits for Power-Constrained Cryptographic Computations

This thesis tackles the need for ultra-low power operation in power-constrained cryptographic computations. An example of such an application could be smartcards. One of the techniques which has proven to have the potential of rendering ultra-low power operation is ‘Adiabatic Logic Technique’. However, the adiabatic circuits has associated challenges due to high energy dissipation of the Power-Clock Generator (PCG) and complexity of the multi-phase power-clocking scheme. Energy efficiency of the adiabatic system is often degraded due to the high energy dissipation of the PCG. In this thesis, nstep charging strategy using tank capacitors is considered for the power-clock generation and several design rules and trade-offs between the circuit complexity and energy efficiency of the PCG using n-step charging circuits have been proposed. Since pipelining is inherent in adiabatic logic design, careful selection of architecture is essential, as otherwise overhead in terms of area and energy due to synchronization buffers is induced specifically, in the case of adiabatic designs using 4-phase power-clocking scheme. Several architectures for the Montgomery multiplier using adiabatic logic technique are implemented and compared. An architecture which constitutes an appropriate trade-off between energy efficiency and throughput is proposed along with its methodology. Also, a strategy to reduce the overhead due to synchronization buffers is proposed. A modification in the Montgomery multiplication algorithm is proposed. Furthermore, a problem due to the application of power-clock gating in cascade stages of adiabatic logic is identified. The problem degrades the energy savings that would otherwise be obtained by the application of power-clock gating. A solution to this problem is proposed. Cryptographic implementations also present an obvious target for Power Analysis Attacks (PAA). There are several existing secure adiabatic logic designs which are proposed as a countermeasure against PAA. Shortcomings of the existing logic designs are identified, and two novel secure adiabatic logic designs are proposed as the countermeasures against PAA and improvement over the existing logic designs

Single-Rail Adiabatic Logic for Energy-Efficient and CPA-Resistant Cryptographic Circuit in Low-Frequency Medical Devices

Designing energy-efficient and secure cryptographic circuits in low-frequency medical devices are challenging due to low-energy requirements. Also, the conventional CMOS logic-based cryptographic circuits solutions in medical devices can be vulnerable to side-channel attacks (e.g. correlation power analysis (CPA)). In this article, we explored single-rail Clocked CMOS Adiabatic Logic (CCAL) to design an energy-efficient and secure cryptographic circuit for low-frequency medical devices. The performance of the CCAL logic-based circuits was checked with a power clock generator (2N2P-PCG) integrated into the design for the frequency range of 50 kHz to 250 kHz. The CCAL logic gates show an average of approximately 48% energy-saving and more than 95% improvement in security metrics performance compared to its CMOS logic gate counterparts. Further, the CCAL based circuits are also compared for energy-saving performance against dual-rail adiabatic logic, 2-EE-SPFAL, and 2-SPGAL. The adiabatic CCAL gates save on an average of 55% energy saving compared to 2-EE-SPFAL and 2-SPGAL over the frequency range of 50 kHz to 250 kHz. To check the efficacy of CCAL to design a larger cryptographic circuit, we implemented a case-study design of a Substitution-box (S-box) of popular lightweight PRESENT-80 encryption. The case-study implementation (2N2P-PCG integrated into the design) using CCAL shows more than 95% energy saving compared to CMOS for the frequency 50 kHz to 125 kHz and around 60% energy saving at frequency 250 kHz. At 250 kHz, compared to the dual-rail adiabatic designs of S-box based on 2-EE-SPFAL and 2-SPGAL, the CCAL based S-box shows 32.67% and 11.21% of energy savings, respectively. Additionally, the CCAL logic gate structure requires a lesser number of transistors compared to dual-rail adiabatic logic. The case-study implementation using CCAL saves 45.74% and 34.88% transistor counts compared to 2-EE-SPFAL and 2-SPGAL. The article also presents the effect of varying tank capacitance in 2N2P-PCG over energy efficiency and security performance. The CCAL based case-study was also subjected against CPA. The CCAL-based S-box case study successfully protects the revelation of the encryption key against the CPA attack, However, the key was revealed in CMOS-based case-study implementation

Adiabatic Approach for Low-Power Passive Near Field Communication Systems

This thesis tackles the need of ultra-low power electronics in the power limited passive Near Field Communication (NFC) systems. One of the techniques that has proven the potential of delivering low power operation is the Adiabatic Logic Technique. However, the low power benefits of the adiabatic circuits come with the challenges due to the absence of single opinion on the most energy efficient adiabatic logic family which constitute appropriate trade-offs between computation time, area and complexity based on the circuit and the power-clocking schemes. Therefore, five energy efficient adiabatic logic families working in single-phase, 2-phase and 4-phase power-clocking schemes were chosen. Since flip-flops are the basic building blocks of any sequential circuit and the existing flip-flops are MUX-based (having more transistors) design, therefore a novel single-phase, 2-phase and 4-phase reset based flip-flops were proposed. The performance of the multi-phase adiabatic families was evaluated and compared based on the design examples such as 2-bit ring counter, 3-bit Up-Down counter and 16-bit Cyclic Redundancy Check (CRC) circuit (benchmark circuit) based on ISO 14443-3A standard. Several trade-offs, design rules, and an appropriate range for the supply voltage scaling for multi-phase adiabatic logic are proposed. Furthermore, based on the NFC standard (ISO 14443-3A), data is frequently encoded using Manchester coding technique before transmitting it to the reader. Therefore, if Manchester encoding can be implemented using adiabatic logic technique, energy benefits are expected. However, adiabatic implementation of Manchester encoding presents a challenge. Therefore, a novel method for implementing Manchester encoding using adiabatic logic is proposed overcoming the challenges arising due to the AC power-clock. Other challenges that come with the dynamic nature of the adiabatic gates and the complexity of the 4-phase power-clocking scheme is in synchronizing the power-clock v phases and the time spent in designing, validation and debugging of errors. This requires a specific modelling approach to describe the adiabatic logic behaviour at the higher level of abstraction. However, describing adiabatic logic behaviour using Hardware Description Languages (HDLs) is a challenging problem due to the requirement of modelling the AC power-clock and the dual-rail inputs and outputs. Therefore, a VHDL-based modelling approach for the 4-phase adiabatic logic technique is developed for functional simulation, precise timing analysis and as an improvement over the previously described approaches

Sustainable and Short-range Communication Techniques for Smart Industry Environment

The industries of the future, call for unprecedented flexibility whereas, the communication technology intervention is the best solution. For sustainable development goals in industry automation demand Dedicated Short-range Communication (DSRC) with Intelligent Transportation Systems (ITS). One of these systems' view point is the regular dissemination of safety messages. Integrating this technology with the existing Industry automation is a technical challenge. Integration also involves in imparting intelligence through digitalization of communication. With a cost of overhead power, Error Controlling Codes (ECC) provides a reliable and error-free DSRC communication system. In this paper, low power and secure digital VLSI architecture is presented to meet the sustainable integrated communication technology on chip circuitry for industry 4.0. The circuit's performance is measured in Cadence utilizing 18 nm FinFET-based ECRL adiabatic logic. The design provides maximum power savings of 99.49% over reported values for CMOS and 99.41% for pass transistor implementation. The adiabatic logic circuits constructed with ECRL are shown to have consistent peak current traces and hence can survive differential power analysis (DPA) attacks, resulting in improved circuit security

Simulation for Reliability, Hardware Security, and Ising Computing in VLSI Chip Design

The continued scaling of VLSI circuits has provided a wealth of opportunities andchallenges to the VLSI circuit design area. Both these challenges and opportunities, however,require new simulation tools that can enable their solution or exploitation as classicalmethods typically dealt with problem domains with smaller scales or less complexity. Inthis dissertation, simulation methods are presented to address the emerging VLSI designtopics of Electromigration induced aging and Ising computing and are then applied to theapplication areas of hardware security and graph partitioning respectively.The Electromigration aging effect in VLSI circuits is a long-term reliability issueaffecting current carrying metal wires leading to IR drop degradation. Typically, simpleanalytical equations can determine a wire’s effective age or if it will be affected by the EMaging effect at all. However, these classical methods are overly conservative and can lead toover design or unnecessary design iterations. Furthermore, it is expected that the EM agingeffect will become more severe in future Integrated Cirucits (ICs) due to increasing currentdensities and the prevalance of polycrystaline copper atom structures seen at small wiredimensions. For this reason, more comprehensive simulation techniques that can efficientlysimulate the EM effect with less conservative results can help mitigate overdesign andincrease design margins while reducing design iterations.The area of Hardware Security is becoming increasingly important as the chipsupply chain becomes more globalized and the integrity of chips becomes more diffiuclt toverify. Utilizing the accurate simulation techniques for EM, we can utilize this reliabilityeffect to demonstrate how a reliability based attack could be perpatrated. Furthermore, wecan utilize this aging effect as a defense mechanism to help us validate the integrity of anIC and detect counterfeit chips in the component supply chain market.Ising computing is an emerging method of solving combinatorial optimization problemsby simulating the interactions of so-called spin glasses and their interactions. Borrowingconcepts from quantum computing, this methods mimics the quantum interaction betweenspin glasses in such a way that finding a ground state of these spin glass models leadsto the solution of a particular problem. In this dissertation, effective methods of simulatingthe spin glass interactions using General Purpose Graphics Processing Units (GPGPUs)and finding their ground state are developed.In addition to the GPU based Ising model simulations, important combinatorialproblems can be mapped to the Ising model. In this dissertation the Ising solver is appliedto graph partitioning which can be utilized in VLSI design and many other domains as well.Specifically, solvers for the maxcut problem and the balanced min-cut partitioning problemare developed