Modeling a IF double sampling bandpass switched capacitor ΣΔ ADC with a symmetric noise transfer function for WiMAX/WLAN

4G technology aims to revolutionize private and professional communication with its ubiquity and high-speed transmission (averaging 100Mbps). WiMAX and WLAN are two of the high speed access technologies to be used in the 4G mobile communication. Apropos to their high bandwidths, oversampling converters, e.g.ΣΔ ADCs, used for these standards would entail high levels of power consumption. Double sampling technique used in ΣΔ ADCs help in reducing the power consumption, since the actual sampling rate is only half the sampling frequency required to achieve a target resolution. But for conventional modulators, with low pass noise transfer functions (NTF), this benefit is hampered by the introduction of folded noise due to the mismatch of sampling capacitances. This paper presents a novel method of designing IF bandpass switched capacitor (SC)ΣΔ modulators with symmetric NTFs. Such a bandpass NTF is formulated with its center frequency at one-fourth the effective sampling frequency. The symmetricity ensures that the folded noise is `noise-shaped' along with the quantization noise. The idea is verified with a discrete time bandpass ΣΔ modulator modeled using Simulink®, including various nonlinearities, viz. clock jitter, opampnonidealities, and capacitive mismatch effects owing to double sampling and use of a multibitquantizer. Behavioral simulations of the proposed non-ideal model for WiMAX and WLAN, with a bandwith of 10MHz and 11MHz, respectively, achieved a peak resolution greater than 10 bits for each of the standards

Resonation-based hybrid continuous-time/discrete-time cascade ΣΔ modulators: application to 4G wireless telecom

This paper presents innovative architectures of hybrid Continuous-Time/Discrete-Time (CT/DT) cascade ΣΔ Modulators (ΣΔMs) made up of a front-end CT stage and a back-end DT stage. In addition to increasing the digitized signal bandwidth as compared to conventional ΣΔMs, the proposed topologies take advantage of the CT nature of the front-end ΣΔM stage, by embedding anti-aliasing filtering as well as their suitability to operate up to the GHz range. Moreover, the presented modulators include multi-bit quantization and Unity Signal Transfer Function (USTF) in both stages to reduce the integrator output swings, and programmable resonation to optimally distribute the zeroes of the overall Noise Transfer Function (NTF), such that the in-band quantization noise is minimized for each operation mode. Both local and inter-stage (global) based resonation architectures are synthesized and compared in terms of their circuit complexity, resolution-bandwidth programmability and robustness with respect to circuit non-ideal effects. The combination of all mentioned characteristics results in novel hybrid ΣΔMs, very suited for the implementation of adaptive/reconfigurable Analog-to-Digital Converters (ADCs) intended for the 4th Generation (4G) of wireless telecom systems

High Performance Integrated Circuit Blocks for High-IF Wideband Receivers

Due to the demand for high‐performance radio frequency (RF) integrated circuit design in the past years, a system‐on‐chip (SoC) that enables integration of analog and digital parts on the same die has become the trend of the microelectronics industry. As a result, a major requirement of the next generation of wireless devices is to support multiple standards in the same chip‐set. This would enable a single device to support multiple peripheral applications and services. Based on the aforementioned, the traditional superheterodyne front‐end architecture is not suitable for such applications as it would require a complete receiver for each standard to be supported. A more attractive alternative is the highintermediate frequency (IF) radio architecture. In this case the signal is digitalized at an intermediate frequency such as 200MHz. As a consequence, the baseband operations, such as down‐conversion and channel filtering, become more power and area efficient in the digital domain. Such architecture releases the specifications for most of the front‐end building blocks, but the linearity and dynamic range of the ADC become the bottlenecks in this system. The requirements of large bandwidth, high frequency and enough resolution make such ADC very difficult to realize. Many ADC architectures were analyzed and Continuous‐Time Bandpass Sigma‐Delta (CT‐BP‐ΣΔ) architecture was found to be the most suitable solution in the high‐IF receiver architecture since they combine oversampling and noise shaping to get fairly high resolution in a limited bandwidth. A major issue in continuous‐time networks is the lack of accuracy due to powervoltage‐ temperature (PVT) tolerances that lead to over 20% pole variations compared to their discrete‐time counterparts. An optimally tuned BP ΣΔ ADC requires correcting for center frequency deviations, excess loop delay, and DAC coefficients. Due to these undesirable effects, a calibration algorithm is necessary to compensate for these variations in order to achieve high SNR requirements as technology shrinks. In this work, a novel linearization technique for a Wideband Low‐Noise Amplifier (LNA) targeted for a frequency range of 3‐7GHz is presented. Post‐layout simulations show NF of 6.3dB, peak S21 of 6.1dB, and peak IIP3 of 21.3dBm, respectively. The power consumption of the LNA is 5.8mA from 2V. Secondly, the design of a CMOS 6th order CT BP‐ΣΔ modulator running at 800 MHz for High‐IF conversion of 10MHz bandwidth signals at 200 MHz is presented. A novel transconductance amplifier has been developed to achieve high linearity and high dynamic range at high frequencies. A 2‐bit quantizer with offset cancellation is alsopresented. The sixth‐order modulator is implemented using 0.18 um TSMC standard analog CMOS technology. Post‐layout simulations in cadence demonstrate that the modulator achieves a SNDR of 78 dB (~13 bit) performance over a 14MHz bandwidth. The modulator’s static power consumption is 107mW from a supply power of ± 0.9V. Finally, a calibration technique for the optimization of the Noise Transfer Function CT BP ΣΔ modulators is presented. The proposed technique employs two test tones applied at the input of the quantizer to evaluate the noise transfer function of the ADC, using the capabilities of the Digital Signal Processing (DSP) platform usually available in mixed‐mode systems. Once the ADC output bit stream is captured, necessary information to generate the control signals to tune the ADC parameters for best Signal‐to‐Quantization Noise Ratio (SQNR) performance is extracted via Least‐ Mean Squared (LMS) software‐based algorithm. Since the two tones are located outside the band of interest, the proposed global calibration approach can be used online with no significant effect on the in‐band content

Fiber Optics

Optical fibers in metrology, telecommunications, sensors, manufacturing, and health science have gained massive research interest. The number of applications is increasing at a fast pace. This book aims to present a collection of recent advances in fiber optics, addressing both fundamental and industrial applications. It covers the current progress and latest breakthroughs in emergent applications of fiber optics. The book includes five chapters on recent developments in optical fiber communications and fiber sensors, as well as the design, simulation, and fabrication of novel fiber concepts

Design of a low power switched-capacitor pipeline analog-to-digital converter

An Analog to Digital Converter (ADC) is a circuit which converts an analog signal into digital signal. Real world is analog, and the data processed by the computer or by other signal processing systems is digital. Therefore, the need for ADCs is obvious. In this thesis, several novel designs used to improve ADCs operation speed and reduce ADC power consumption are proposed. First, a high speed switched source follower (SSF) sample and hold amplifier without feedthrough penalty is implemented and simulated. The SSF sample and hold amplifier can achieve 6 Bit resolution with sampling rate at 10Gs/s. Second, a novel rail-to-rail time domain comparator used in successive approximation register ADC (SAR ADC) is implemented and simulated. The simulation results show that the proposed SAR ADC can only consume 1.3 muW with a 0.7 V power supply. Finally, a prototype pipeline ADC is implemented and fabricated in an IBM 90nm CMOS process. The proposed design is validated using measurement on a fabricated silicon IC, and the proposed 10-bit ADC achieves a peak signal-to-noise- and-distortion-ratio (SNDR) of 47 dB. This SNDR translates to a figure of merit (FOM) of 2.6N/conversion-step with a 1.2 V power supply