1,376 research outputs found

    High-Voltage-Gain DC-DC Power Electronic Converters -- New Topologies and Classification

    Get PDF
    This dissertation proposes two new high-voltage-gain dc-dc converters for integration of renewable energy sources in 380/400V dc distribution systems. The first high-voltage-gain converter is based on a modified Dickson charge pump voltage multiplier circuit. The second high-voltage-gain converter is based on a non-inverting diode-capacitor voltage multiplier cell. Both the proposed converters offer continuous input current and low voltage stress on switches which make them appealing for applications like integration of renewable energy sources. The proposed converters are capable for drawing power from a single source or two sources while having continuous input current in both cases. Theoretical analysis of the operation of the proposed converters and the component stresses are discussed with supporting simulation and hardware results. This dissertation also proposes a family of high-voltage-gain dc-dc converters that are based on a generalized structure. The two stage general structure consists of a two-phase interleaved (TPI) boost stage and a voltage multiplier (VM) stage. The TPI boost stage results in a classification of the family of converters into non-isolated and isolated converters. A few possible VM stages are discussed. The voltage gain derivations of the TPI boost stages and VM stages are presented in detail. An example converter is discussed with supporting hardware results to verify the general structure. The proposed family of converters can be powered using single source or two sources while having continuous input current in both cases. These high voltage gain dc-dc converters are modular and scalable; making them ideal for harnessing energy from various renewable sources offering power at different levels --Abstract, page iv

    Advanced topologies of high step-up DC-DC converters for renewable energy applications

    Get PDF
    This research is focused on developing several advanced topologies of high step-up DC-DC converters to connect low-voltage renewable energy (RE) sources, such as photovoltaic (PV) panels and fuel cells (FCs), into a high-voltage DC bus in renewable energy applications. The proposed converters are based on the combinations of various voltage-boosting (VB) techniques, including interleaved and quadratic structures, switched-capacitor (SC)-based voltage multiplier (VM) cells, and magnetically coupled inductor (CI) and built-in-transformer (BIT). The proposed converters offer outstanding features, including high voltage gain with low or medium duty cycle, a small number of components, low current and voltage stresses on the components, continuous input current with low ripple, and high efficiency. This research includes five new advanced high step-up DC-DC converters with detailed analyses. First, an interleaved converter is presented, which is based on the integration of two three-winding CIs with SC-based VM cells. Second, a dual-switch converter is proposed, which is based on the integration of a single three-winding CI with SC-based VM cells. Third, the SC-based VM cells are utilized to present three new Z-source (ZS)-based converters. Fourth, two double-winding CIs and a three-winding BIT are combined with SC-based VM cells to develop another interleaved high step-up converter. Finally, two double-winding CIs and SC-based VM cells are adopted to devise an interleaved quadratic converter with high voltage gain. The operating and steady-state analyses, design considerations, and a comparison with similar converters in the literature are provided for each converter. In addition, hardware prototypes were fabricated to verify the performance of the proposed converters --Abstract, page iv

    Topics in Analysis and Design of Primary Parallel Isolated Boost Converter

    Get PDF

    Performance Enhancement of High Step-up DC-DC Converter to Attain High Efficiency and Low Voltage Stress

    Full text link
    This study proposes a new high voltage gain and high-efficiency DC-DC converter to interface renewable energy resources into dc nanogrid. The proposed topology is formed by a coupled inductor to achieve high voltage gain and low stress on the active switch. The switch voltage stress is significantly low compared to the output voltage. Thus, efficiency is improved by utilizing a low voltage rating MOSFET. Furthermore, the utilization of couple inductor eliminated the reverse recovery losses of diodes. The converter consists of the least number of components that decrease the overall system cost. The steady-state operation and analysis of the proposed converter are discussed comprehensively. The experimental performance is verified by building and testing a prototype in the laboratory. The experimental results prove the consistency with the theoretical analysis. The converter depicts a peak efficiency of 97.10% in the laboratory

    Modular Power Electronic Converters in the Power Range 1 to 10 kW

    Get PDF

    Impedance Source Converters for Renewable Energy Systems

    Get PDF

    A New Soft-Switched High Step-Up Trans-Inverse DC/DC Converter Based on Built-In Transformer

    Get PDF
    This article proposes a new Zero-Voltage Switching (ZVS) high step-up DC/DC converter based on a built-in transformer for renewable energy applications. The proposed topology utilizes a Three-Winding Built-In Transformer (TWBT) to increase the voltage gain, but unlike most coupled-inductor-based DC-DC converters, high output voltages can be obtained under a lower magnetic turns ratio. In this circuit, with the help of a regenerative active clamp circuit, the energy of the leakage inductor from the TWBT is absorbed and transferred to the output, therefore, the ZVS conditions at turn-on time are achieved for switches. The voltage stresses across the switches of the proposed topology are limited, and the diodes reverse-recovery issue are eliminated. Due to the low input current ripple, the suggested topology can be used for renewable energy sources. Furthermore, because of the low number of components along with the soft-switching operation, the proposed circuit can offer enough high efficiency. The operational principle, steady-state analysis, and characteristics of the proposed converter are provided. Finally, a 200 W prototype with 25 V input and 400 V output voltage is built to validate the analytical results

    Soft-Switched Step-Up Medium Voltage Power Converters

    Get PDF
    With a ten-year average annual growth rate of 19 percent, wind energy has been the largest source of new electricity generation for the past decade. Typically, an offshore wind farm has a medium voltage ac (MVac) grid that collects power from individual wind turbines. Since the output voltage of a wind turbine is too low (i.e., typically 400 690 V) to be connected to the MVac grid (i.e., 20 40 kV), a heavy line-frequency transformer is used to step up the individual turbines output voltage to the MV level. To eliminate the need for bulky MVac transformers, researchers are gravitating towards the idea of replacing the MVac grid with a medium voltage dc (MVdc) grid, so that MV step-up transformers are replaced by MV step-up power electronic converters that operate at the medium frequency range with much lower size and weight. This dissertation proposes a class of modular step-up transformerless MV SiC-based power converters with soft-switching capability for wind energy conversion systems with MVdc grid. This dissertation consists of two parts: the first part focuses on the development of two novel groups of step-up isolated dc-dc MV converters that utilize various step-up resonant circuits and soft-switched high voltage gain rectifier modules. An integrated magnetic design approach is also presented to combine several magnetic components together in the modular high voltage gain rectifiers. The second part of this dissertation focuses on the development of several three-phase ac-dc step-up converters with integrated active power factor correction. In particular, a bridgeless input ac-dc rectifier is also proposed to combine with the devised step-up transformerless dc-dc converters (presented in the first part) to form the three-phase soft-switched ac-dc step-up voltage conversion unit. In each of the presented modular step-up converter configurations, variable frequency control is used to regulate the output dc voltage of each converter module. The operating principles and characteristics of each presented converter are provided in detail. The feasibility and performance of all the power converter concepts presented in this dissertation are verified through simulation results on megawatts (MW) design examples, as well as experimental results on SiC-based laboratory-scale proof-of-concept prototypes

    Design and implementation of two non-isolated high gain DC-DC converters

    Get PDF
    In most solar energy systems, the output voltage of a photovoltaic panel is usually between 20 to 40 Vdc. In order to interface the panels to a 400 Vdc bus, a high voltage gain dc-dc converter is required. This thesis starts with analyzing and simulating several topologies that have been already introduced for this application. The voltage gain and efficiency are investigated analytically. A hardware prototype of one of the existing topologies, the interleaved boost converter with voltage multiplier cell, has been developed. Finally, a new topology with a higher voltage transfer ratio is proposed and its experimental results are compared with former topologies. Simulations are used to verify the design and predict the performance of each topology --Abstract, page iii
    • …
    corecore