Multispectral Quantum Dots-in-a-Well Infrared Detectors Using Plasmon Assisted Cavities

We present the design, fabrication, and characterization, of multi-spectral quantum dots-in-a-well (DWELL) infrared detectors, by the integration of a surface plasmon assisted resonant cavity with the infrared detector. A square lattice and rectangular lattice cavity, formed by modifying the square lattice have been used in this design. By confining the resonant mode of the cavity to detector active region, the detector responsivity and detectivity have been improved by a factor of 5. A spectral tuning of 5.5 to 7.2 μm has been observed in the peak response of the detectors, by tuning the lattice constant of the cavity. Simulations indicate the presence of two modes of absorption, which have been experimentally verified. The use of a rectangular lattice predicts highly polarization sensitive modes in x- and y-direction, which are observed in fabricated detectors. A peak detectivity of 3.1 x 10^9 cm √(Hz)/W was measured at 77 K. This design offers a cost-effective and simple method of encoding spectral and polarization information, in infrared focal plane arrays

The Brazilian Tunable Filter Imager for the SOAR telescope

This paper presents a new Tunable Filter Instrument for the SOAR telescope. The Brazilian Tunable Filter Imager (BTFI) is a versatile, new technology, tunable optical imager to be used in seeing-limited mode and at higher spatial fidelity using the SAM Ground-Layer Adaptive Optics facility at the SOAR telescope. The instrument opens important new science capabilities for the SOAR community, from studies of the centers of nearby galaxies and the insterstellar medium to statistical cosmological investigations. The BTFI takes advantage of three new technologies. The imaging Bragg Tunable Filter concept utilizes Volume Phase Holographic Gratings in a double-pass configuration, as a tunable filter, while a new Fabry-Perot (FP) concept involves technologies which allow a single FP etalon to act over a large range of interference orders and spectral resolutions. Both technologies will be in the same instrument. Spectral resolutions spanning the range between 25 and 30,000 can be achieved through the use of iBTF at low resolution and scanning FPs beyond R ~2,000. The third new technologies in BTFI is the use of EMCCDs for rapid and cyclically wavelength scanning thus mitigating the damaging effect of atmospheric variability through data acquisition. An additional important feature of the instrument is that it has two optical channels which allow for the simultaneous recording of the narrow-band, filtered image with the remaining (complementary) broad-band light. This avoids the uncertainties inherent in tunable filter imaging using a single detector. The system was designed to supply tunable filter imaging with a field-of-view of 3 arcmin on a side, sampled at 0.12" for direct Nasmyth seeing-limited area spectroscopy and for SAM's visitor instrument port for GLAO-fed area spectroscopy. The instrument has seen first light, as a SOAR visitor instrument. It is now in comissioning phase.Comment: accepted in PAS

Swept-wavelength mid-infrared fiber laser for real-time ammonia gas sensing

The mid-infrared (mid-IR) spectral region holds great promise for new laser-based sensing technologies, based on measuring strong mid-IR molecular absorption features. Practical applications have been limited to date, however, by current low-brightness broadband mid-IR light sources and slow acquisition-time detection systems. Here, we report a new approach by developing a swept-wavelength mid-infrared fiber laser, exploiting the broad emission of dysprosium and using an acousto-optic tunable filter to achieve electronically controlled swept-wavelength operation from 2.89 to 3.25 {\mu}m (3070-3460 cm^-1). Ammonia (NH3) absorption spectroscopy is demonstrated using this swept source with a simple room-temperature single-pixel detector, with 0.3 nm resolution and 40 ms acquisition time. This creates new opportunities for real-time high-sensitivity remote sensing using simple, compact mid-IR fiber-based technologies.Comment: Invited article for APL Photonic

A novel two-section tunable discrete mode Fabry-PÉrot laser exhibiting nanosecond wavelength switching

A novel widely tunable laser diode is proposed and demonstrated. Mode selection occurs by etching perturbing slots into the laser ridge. A two-section device is realized with different slot patterns in each section allowing Vernier tuning. The laser operates at 1.3 mum and achieves a maximum output power of 10 mW. A discontinuous tuning range of 30 nm was achieved with a side mode suppression greater than 30 dB. Wavelength switching times of approximately 1.5 ns between a number of wavelength channels separated by 7 nm have been demonstrated

Chalcogenide Glass-on-Graphene Photonics

Two-dimensional (2-D) materials are of tremendous interest to integrated photonics given their singular optical characteristics spanning light emission, modulation, saturable absorption, and nonlinear optics. To harness their optical properties, these atomically thin materials are usually attached onto prefabricated devices via a transfer process. In this paper, we present a new route for 2-D material integration with planar photonics. Central to this approach is the use of chalcogenide glass, a multifunctional material which can be directly deposited and patterned on a wide variety of 2-D materials and can simultaneously function as the light guiding medium, a gate dielectric, and a passivation layer for 2-D materials. Besides claiming improved fabrication yield and throughput compared to the traditional transfer process, our technique also enables unconventional multilayer device geometries optimally designed for enhancing light-matter interactions in the 2-D layers. Capitalizing on this facile integration method, we demonstrate a series of high-performance glass-on-graphene devices including ultra-broadband on-chip polarizers, energy-efficient thermo-optic switches, as well as graphene-based mid-infrared (mid-IR) waveguide-integrated photodetectors and modulators

The Berkeley tunable far infrared laser spectrometers

A detailed description is presented for a tunable far infrared laser spectrometer based on frequency mixing of an optically pumped molecular gas laser with tunable microwave radiation in a Schottky point contact diode. The system has been operated on over 30 laser lines in the range 10–100 cm^–1 and exhibits a maximum absorption sensitivity near one part in 10^6. Each laser line can be tuned by ±110 GHz with first-order sidebands. Applications of this instrument are detailed in the preceding paper

Tunable superlattice p-i-n photodetectors: characteristics, theory, and application

Extended measurements and theory on the recently developed monolithic wavelength demultiplexer consisting of voltage-tunable superlattice p-i-n photodetectors in a waveguide confirmation are discussed. It is shown that the device is able to demultiplex and detect two optical signals with a wavelength separation of 20 nm directly into different electrical channels at a data rate of 1 Gb/s and with a crosstalk attenuation varying between 20 and 28 dB, depending on the polarization. The minimum acceptable crosstalk attenuation at a data rate of 100 Mb/s is determined to be 10 dB. The feasibility of using the device as a polarization angle sensor for linearly polarized light is also demonstrated. A theory for the emission of photogenerated carriers out of the quantum wells is included, since this is potentially a speed limiting mechanism in these detectors. It is shown that a theory of thermally assisted tunneling by polar optical phonon interaction is able to predict emission times consistent with the observed temporal response

Chromatic dispersion monitoring for high-speed WDM systems using two-photon absorption in a semiconductor microcavity

This paper presents a theoretical and experimental investigation into the use of a two-photon absorption (TPA) photodetector for use in chromatic dispersion (CD) monitoring in high-speed, WDM network. In order to overcome the inefficiency associated with the nonlinear optical-to-electrical TPA process, a microcavity structure is employed. An interesting feature of such a solution is the fact that the microcavity enhances only a narrow wavelength range determined by device design and angle at which the signal enters the device. Thus, a single device can be used to monitor a number of different wavelength channels without the need for additional external filters. When using a nonlinear photodetector, the photocurrent generated for Gaussian pulses is inversely related to the pulsewidth. However, when using a microcavity structure, the cavity bandwidth also needs to be considered, as does the shape of the optical pulses incident on the device. Simulation results are presented for a variety of cavity bandwidths, pulse shapes and durations, and spacing between adjacent wavelength channels. These results are verified experimental using a microcavity with a bandwidth of 260 GHz (2.1 nm) at normal incident angle, with the incident signal comprising of two wavelength channels separated by 1.25 THz (10 nm), each operating at an aggregate data rate of 160 Gb/s. The results demonstrate the applicability of the presented technique to monitor accumulated dispersion fluctuations in a range of 3 ps/nm for 160 Gb/s RZ data channel