An FPGA Architecture and CAD Flow Supporting Dynamically Controlled Power Gating

© 2015 IEEE.Leakage power is an important component of the total power consumption in field-programmable gate arrays (FPGAs) built using 90-nm and smaller technology nodes. Power gating was shown to be effective at reducing the leakage power. Previous techniques focus on turning OFF unused FPGA resources at configuration time; the benefit of this approach depends on resource utilization. In this paper, we present an FPGA architecture that enables dynamically controlled power gating, in which FPGA resources can be selectively powered down at run-time. This could lead to significant overall energy savings for applications having modules with long idle times. We also present a CAD flow that can be used to map applications to the proposed architecture. We study the area and power tradeoffs by varying the different FPGA architecture parameters and power gating granularity. The proposed CAD flow is used to map a set of benchmark circuits that have multiple power-gated modules to the proposed architecture. Power savings of up to 83% are achievable for these circuits. Finally, we study a control system of a robot that is used in endoscopy. Using the proposed architecture combined with clock gating results in up to 19% energy savings in this application

Power Efficient Data-Aware SRAM Cell for SRAM-Based FPGA Architecture

The design of low-power SRAM cell becomes a necessity in today\u27s FPGAs, because SRAM is a critical component in FPGA design and consumes a large fraction of the total power. The present chapter provides an overview of various factors responsible for power consumption in FPGA and discusses the design techniques of low-power SRAM-based FPGA at system level, device level, and architecture levels. Finally, the chapter proposes a data-aware dynamic SRAM cell to control the power consumption in the cell. Stack effect has been adopted in the design to reduce the leakage current. The various peripheral circuits like address decoder circuit, write/read enable circuits, and sense amplifier have been modified to implement a power-efficient SRAM-based FPGA

自律電源電圧制御に基づく低消費電力リコンフィギャラブルVLSI アーキテクチャに関する研究

Tohoku University亀山充隆課

FPGA structures for high speed and low overhead dynamic circuit specialization

A Field Programmable Gate Array (FPGA) is a programmable digital electronic chip. The FPGA does not come with a predefined function from the manufacturer; instead, the developer has to define its function through implementing a digital circuit on the FPGA resources. The functionality of the FPGA can be reprogrammed as desired and hence the name “field programmable”. FPGAs are useful in small volume digital electronic products as the design of a digital custom chip is expensive. Changing the FPGA (also called configuring it) is done by changing the configuration data (in the form of bitstreams) that defines the FPGA functionality. These bitstreams are stored in a memory of the FPGA called configuration memory. The SRAM cells of LookUp Tables (LUTs), Block Random Access Memories (BRAMs) and DSP blocks together form the configuration memory of an FPGA. The configuration data can be modified according to the user’s needs to implement the user-defined hardware. The simplest way to program the configuration memory is to download the bitstreams using a JTAG interface. However, modern techniques such as Partial Reconfiguration (PR) enable us to configure a part in the configuration memory with partial bitstreams during run-time. The reconfiguration is achieved by swapping in partial bitstreams into the configuration memory via a configuration interface called Internal Configuration Access Port (ICAP). The ICAP is a hardware primitive (macro) present in the FPGA used to access the configuration memory internally by an embedded processor. The reconfiguration technique adds flexibility to use specialized ci rcuits that are more compact and more efficient t han t heir b ulky c ounterparts. An example of such an implementation is the use of specialized multipliers instead of big generic multipliers in an FIR implementation with constant coefficients. To specialize these circuits and reconfigure during the run-time, researchers at the HES group proposed the novel technique called parameterized reconfiguration that can be used to efficiently and automatically implement Dynamic Circuit Specialization (DCS) that is built on top of the Partial Reconfiguration method. It uses the run-time reconfiguration technique that is tailored to implement a parameterized design. An application is said to be parameterized if some of its input values change much less frequently than the rest. These inputs are called parameters. Instead of implementing these parameters as regular inputs, in DCS these inputs are implemented as constants, and the application is optimized for the constants. For every change in parameter values, the design is re-optimized (specialized) during run-time and implemented by reconfiguring the optimized design for a new set of parameters. In DCS, the bitstreams of the parameterized design are expressed as Boolean functions of the parameters. For every infrequent change in parameters, a specialized FPGA configuration is generated by evaluating the corresponding Boolean functions, and the FPGA is reconfigured with the specialized configuration. A detailed study of overheads of DCS and providing suitable solutions with appropriate custom FPGA structures is the primary goal of the dissertation. I also suggest different improvements to the FPGA configuration memory architecture. After offering the custom FPGA structures, I investigated the role of DCS on FPGA overlays and the use of custom FPGA structures that help to reduce the overheads of DCS on FPGA overlays. By doing so, I hope I can convince the developer to use DCS (which now comes with minimal costs) in real-world applications. I start the investigations of overheads of DCS by implementing an adaptive FIR filter (using the DCS technique) on three different Xilinx FPGA platforms: Virtex-II Pro, Virtex-5, and Zynq-SoC. The study of how DCS behaves and what is its overhead in the evolution of the three FPGA platforms is the non-trivial basis to discover the costs of DCS. After that, I propose custom FPGA structures (reconfiguration controllers and reconfiguration drivers) to reduce the main overhead (reconfiguration time) of DCS. These structures not only reduce the reconfiguration time but also help curbing the power hungry part of the DCS system. After these chapters, I study the role of DCS on FPGA overlays. I investigate the effect of the proposed FPGA structures on Virtual-Coarse-Grained Reconfigurable Arrays (VCGRAs). I classify the VCGRA implementations into three types: the conventional VCGRA, partially parameterized VCGRA and fully parameterized VCGRA depending upon the level of parameterization. I have designed two variants of VCGRA grids for HPC image processing applications, namely, the MAC grid and Pixie. Finally, I try to tackle the reconfiguration time overhead at the hardware level of the FPGA by customizing the FPGA configuration memory architecture. In this part of my research, I propose to use a parallel memory structure to improve the reconfiguration time of DCS drastically. However, this improvement comes with a significant overhead of hardware resources which will need to be solved in future research on commercial FPGA configuration memory architectures

A Survey of FPGA Optimization Methods for Data Center Energy Efficiency

This article provides a survey of academic literature about field programmable gate array (FPGA) and their utilization for energy efficiency acceleration in data centers. The goal is to critically present the existing FPGA energy optimization techniques and discuss how they can be applied to such systems. To do so, the article explores current energy trends and their projection to the future with particular attention to the requirements set out by the European Code of Conduct for Data Center Energy Efficiency. The article then proposes a complete analysis of over ten years of research in energy optimization techniques, classifying them by purpose, method of application, and impacts on the sources of consumption. Finally, we conclude with the challenges and possible innovations we expect for this sector.Comment: Accepted for publication in IEEE Transactions on Sustainable Computin

Energy Optimization in Commercial FPGAs with Voltage, Frequency and Logic Scaling

This paper investigates the energy reductions possible in commercially available FPGAs configured to support voltage, frequency and logic scalability combined with power gating. Voltage and frequency scaling is based on in-situ detectors that allow the device to detect valid working voltage and frequency pairs at run-time while logic scalability is achieved with partial dynamic reconfiguration. The considered devices are FPGA-processor hybrids with independent power domains fabricated in 28 nm process nodes. The test case is based on a number of operational scenarios in which the FPGA side is loaded with a motion estimation core that can be configured with a variable number of execution units. The results demonstrate that voltage scalability reduces power by up to 60 percent compared with nominal voltage operation at the same frequency. The energy analysis show that the most energy efficiency core configuration depends on the performance requirements. A low performance scenario shows that serial computation is more energy efficient than the parallel configuration while the opposite is true when the performance requirements increase. An algorithm is proposed to combine effectively adaptive voltage/logic scaling and power gating in the proposed system and application

Software Defined Radio Equipment: What's the Best Design Approach to Reduce Power Consumption and Increase Reconfigurability ?

International audienc

Execution modeling in self-aware FPGA-based architectures for efficient resource management

SRAM-based FPGAs have significantly improved their performance and size with the use of newer and ultra-deep-submicron technologies, even though power consumption, together with a time-consuming initial configuration process, are still major concerns when targeting energy-efficient solutions. System self-awareness enables the use of strategies to enhance system performance and power optimization taking into account run-time metrics. This is of particular importance when dealing with reconfigurable systems that may make use of such information for efficient resource management, such as in the case of the ARTICo3 architecture, which fosters dynamic execution of kernels formed by multiple blocks of threads allocated in a variable number of hardware accelerators, combined with module redundancy for fault tolerance and other dependability enhancements, e.g. side-channel-attack protection. In this paper, a model for efficient dynamic resource management focused on both power consumption and execution times in the ARTICo3 architecture is proposed. The approach enables the characterization of kernel execution by using the model, providing additional decision criteria based on energy efficiency, so that resource allocation and scheduling policies may adapt to changing conditions. Two different platforms have been used to validate the proposal and show the generalization of the model: a high-performance wireless sensor node based on a Spartan-6 and a standard off-the-shelf development board based on a Kintex-7