724 research outputs found
Characterization and Utilization of 600 V GaN GITs for 4.5 kW Single Phase Inverter Design
Superior properties allow for faster switching and higher power density converters. However, the fast switching capability of GaN, while theoretically beneficial to converter design, presents several challenges due to the presence of printed circuit board (PCB) and device parasitics. Therefore, it is imperative that the results of device characterization reflect actual device behavior in order to adequately model the device for converter design. This thesis focuses on characterization and utilization of 600 V/30 A Gallium Nitride gate injection transistors, or GaN GITs. The experimental data from static and dynamic characterization was used to maximize the performance of the devices in each phase leg of a 4.5 kW, single-phase, full-bridge inverter. The impact of PCB and device parasitics on switching behavior was also investigated, and a trade-off study of switching loss, overshoot voltage, and dead time loss is presented. Device packaging is also of interest regarding the design of high-frequency devices. This thesis compares the impact of two package designs for the GIT device by designing two separate inverters with the same specifications utilizing the different packages. Finally, due to the lower critical energy of the GaN HEMT during a short circuit, this thesis studies the short-circuit robustness of the devices. The performance of a unique gate sensing protection scheme is compared between two different packages, and the impact of the gate drive and protection circuit design parameters on performance is evaluated
Field Programmable Gate Arrays Usage in Industrial Automation Systems
Tato disertační práce se zabývá využitím programovatelných hradlových polí (FPGA) v diagnostice měničů, využívajících spínaných IGBT tranzistorů. Je zaměřena na budiče těchto výkonových tranzistorů a jejich struktury. Přechodné jevy veličin, jako jsou IG, VGE, VCE během procesu přepínání (zapnutí, vypnutí), mohou poukazovat na degradaci IGBT. Pro měření a monitorování těchto veličin byla navržena nová architektura budiče IGBT. Rychlé měření a monitorování během přepínacího děje vyžaduje vysokou vzorkovací frekvenci. Proto jsou navrhovány paralelní vysokorychlostní AD převodníky (> 50 MSPS). Práce je zaměřena převážně na návrh zařízení s FPGA včetně hardware a software. Byla navržena nová deska plošných spojů s FPGA, která plní požadované funkce, jako je řízení IGBT pomocí vícenásobných paralelních koncových stupňů, monitorování a diagnostiku, a propojení s řídicí jednotkou měniče.This doctoral thesis deals with the usage of Field Programmable Gate Arrays (FPGAs) in a diagnosis of power inverters which use the IGBTs transistors as switching devices. It is focused on the IGBT gate drives and their structures. As long as the transient phenomena and other quantities such as IG, VGE, VCE shows the IGBT degradation during the switching process (turn-on, turn-off), a new IGBT gate driver architecture is proposed for measuring and monitoring these quantities. Quick measurements and monitoring during the IGBT switching process require high sampling frequencies. Therefore, high speed parallel ADC converters (> 50MSPS) are proposed. The thesis is focused on the FPGA design (hardware, software). A new FPGA board is designed for desired functions implementation such as IGBT driving using multiple stages, IGBT monitoring and diagnosis, and interfacing to inverter controller.
High-power converters for space applications
Phase 1 was a concept definition effort to extend space-type dc/dc converter technology to the megawatt level with a weight of less than 0.1 kg/kW (220 lb./MW). Two system designs were evaluated in Phase 1. Each design operates from a 5 kV stacked fuel cell source and provides a voltage step-up to 100 kV at 10 A for charging capacitors (100 pps at a duty cycle of 17 min on, 17 min off). Both designs use an MCT-based, full-bridge inverter, gaseous hydrogen cooling, and crowbar fault protection. The GE-CRD system uses an advanced high-voltage transformer/rectifier filter is series with a resonant tank circuit, driven by an inverter operating at 20 to 50 kHz. Output voltage is controlled through frequency and phase shift control. Fast transient response and stability is ensured via optimal control. Super-resonant operation employing MCTs provides the advantages of lossless snubbing, no turn-on switching loss, use of medium-speed diodes, and intrinsic current limiting under load-fault conditions. Estimated weight of the GE-CRD system is 88 kg (1.5 cu ft.). Efficiency of 94.4 percent and total system loss is 55.711 kW operating at 1 MW load power. The Maxwell system is based on a resonance transformer approach using a cascade of five LC resonant sections at 100 kHz. The 5 kV bus is converted to a square wave, stepped-up to a 100 kV sine wave by the LC sections, rectified, and filtered. Output voltage is controlled with a special series regulator circuit. Estimated weight of the Maxwell system is 83.8 kg (4.0 cu ft.). Efficiency is 87.2 percent and total system loss is 146.411 kW operating at 1 MW load power
Kilovolt dc solid state remote power controller development
The experience gained in developing and applying solid state power controller (SSPC) technology at high voltage dc (HVDC) potentials and power levels of up to 25 kilowatts is summarized. The HVDC switching devices, power switching concepts, drive circuits, and very fast acting overcurrent protection circuits were analyzed. A 25A bipolar breadboard with Darlington connected switching transistor was built. Fault testing at 900 volts was included. A bipolar transistor packaged breadboard design was developed. Power MOSFET remote power controller (RPC) was designed
System configuration, fault detection, location, isolation and restoration: a review on LVDC Microgrid protections
Low voltage direct current (LVDC) distribution has gained the significant interest of research due to the advancements in power conversion technologies. However, the use of converters has given rise to several technical issues regarding their protections and controls of such devices under faulty conditions. Post-fault behaviour of converter-fed LVDC system involves both active converter control and passive circuit transient of similar time scale, which makes the protection for LVDC distribution significantly different and more challenging than low voltage AC. These protection and operational issues have handicapped the practical applications of DC distribution. This paper presents state-of-the-art protection schemes developed for DC Microgrids. With a close look at practical limitations such as the dependency on modelling accuracy, requirement on communications and so forth, a comprehensive evaluation is carried out on those system approaches in terms of system configurations, fault detection, location, isolation and restoration
Protection in Low Voltage DC Microgrids
Protection is an important aspect when designing a microgrid system, as it ensures the network is able to run safely. As the debate between AC vs. DC protection schemes continue, there appear to be distinct advantages and disadvantages on each side with respect to reliability, efficiency, security, environmental and economic concerns. In this thesis, a low voltage DC microgrid protection scheme used in a data center is proposed. The final goal of this project is to develop a network and perform a fault analysis study while investigating different aspects of power protection schemes. Research is done on different protection devices which will be used to protect their respective components.
Three types of faults will be tested on the system for fault current observation purposes. In order to calculate the theoretical fault current of the battery and converter, Microsoft Excel will be used. ICAPS by Intusoft will be used to simulate three different faults in the network. Fault 1 will be on the positive and negative pole of the converter/battery and the load. Fault 2 is a double line to ground fault located on one of the feeders near the load. Fault 3 is a single line to ground impedance located on one of the positive pole of the feeder with a high impedance.
Results show that there are commercial devices available to protect components in such a system. Ultra hybrid DC circuit breakers are used to protect the converter, Molded Case Circuit Breakers are used for feeder protection, and lastly fuses or circuit breakers can be used for battery protection
Universal Short-Circuit and Open-Circuit Fault Detection for an Inverter
Short-circuit and open-circuit faults of an inverter’s power device often lead to catastrophic failure of the entire system if not detected and acted upon within a few microseconds, particularly for emerging wide bandgap (WGB) power semiconductors. While a significant amount of research has been done on the fast and accurate protection and detection of short-circuit faults, there has been less success corresponding to the research on open-circuit faults. Common downfalls include protection and detection that are too application-specific, take longer than a couple of microseconds, and are not cost-efficient. This study proposes a new open-circuit fault protection and detection system integrated with a pre-existing short-circuit system called desaturation protection. First, a literature review is conducted to confirm the necessity of the new protection and detection scheme. Second, the operation principle of the newly proposed protection and detection circuitry is discussed, and design considerations are given. Third, a comprehensive case study revolving around implementing the new protection and detection system is conducted using Synopsys/Saber simulation software. Fourth, an experiment is devised and constructed to showcase the protection and detection scheme’s success, effectiveness, and adaptability in a real-world environment. Fifth, concluding remarks are given, summarizing all the work presented in this study. The results of testing the proposed system illustrate the success and reliability of the new fault protection and detection system
Predictive permanent magnet synchronous generator based small-scale wind energy system at dynamic wind speed analysis for residential net-zero energy building
Integration of small-scale wind energy system to residential buildings for a target to achieve net-zero CO2 emissions is a revolutionary step to reduce the dependency on the national grid. In this paper, a predictive 20 kVA permanent magnet synchronous generator (PMSG) based small scale wind turbine is investigated at dynamic wind speed with a sensing control system to manage and monitor the power flow for a supply to a typical residential building. A control system is applied that regulates the power from the wind turbine. Results indicate that the proposed control system maximizes the power efficiency within the system. The maximum power generation capacity of the wind turbine is 20 kWh with 415 VAC and 50 Hz frequency. A storage system of 19.2 kWh that supplies the energy to the load side. The applied control unit improves the energy management and protects the power equipment during the faults. The research is conducted using MATLAB/SIMULINK and mathematical formulations
A Silicon Carbide Based Solid-State Fault Current Limiter for Modern Power Distribution Systems
The fault current limiter represents a developing technology which will greatly improve the reliability and stability of the power grid. By reducing the magnitude of fault currents in distribution systems, fault current limiters can alleviate much of the damage imposed by these events. Solid-state fault current limiters in particular offer many improved capabilities in comparison to the power system protection equipment which is currently being used for fault current mitigation. The use of silicon carbide power semiconductor devices in solid-state fault current limiters produces a system that would help to advance the infrastructure of the electric grid.
A solid-state fault current limiter utilizing silicon carbide super gate-turn off thyristors (SGTOs) and silicon carbide PiN diodes was designed, built, and tested as a technology demonstrator. The impact of using silicon carbide (SiC) devices in this application was assessed, as well as the associated design challenges. The feasibility of implementing SiC based solid-state fault current limiters for 15 kV class distribution systems was investigated in order to determine the practicality of wide-scale deployment
- …