Frequency Synthesis in Wireless and Wireline Systems

First, a frequency synthesizer for IEEE 802.15.4 / ZigBee transceiver applications that employs dynamic True Single Phase Clocking (TSPC) circuits in its frequency dividers is presented and through the analysis and measurement results of this synthesizer, the need for low power circuit techniques in frequency dividers is discussed. Next, Differential Cascode Voltage-Switch-Logic (DCVSL) based delay cells are explored for implementing radio-frequency (RF) frequency dividers of low power frequency synthesizers. DCVSL ip- ops offer small input and clock capacitance which makes the power consumption of these circuits and their driving stages, very low. We perform a delay analysis of DCVSL circuits and propose a closed-form delay model that predicts the speed of DCVSL circuits with 8 percent worst case accuracy. The proposed delay model also demonstrates that DCVSL circuits suffer from a large low-to-high propagation delay ( PLH) which limits their speed and results in asymmetrical output waveforms. Our proposed enhanced DCVSL, which we call DCVSL-R, solves this delay bottleneck, reducing PLH and achieving faster operation. We implement two ring-oscillator-based voltage controlled oscillators (VCOs) in 0.13 mu m technology with DCVSL and DCVSL-R delay cells. In measurements, for the same oscillation frequency (2.4GHz) and same phase noise (-113dBc/Hz at 10MHz), DCVSL-R VCO consumes 30 percent less power than the DCVSL VCO. We also use the proposed DCVSL-R circuit to implement the 2.4GHz dual-modulus prescaler of a low power frequency synthesizer in 0.18 mu m technology. In measurements, the synthesizer exhibits -135dBc/Hz phase noise at 10MHz offset and 58 mu m settling time with 8.3mW power consumption, only 1.07mWof which is consumed by the dual modulus prescaler and the buffer that drives it. When compared to other dual modulus prescalers with similar division ratios and operating frequencies in literature, DCVSL-R dual modulus prescaler demonstrates the lowest power consumption. An all digital phase locked loop (ADPLL) that operates for a wide range of frequencies to serve as a multi-protocol compatible PLL for microprocessor and serial link applications, is presented. The proposed ADPLL is truly digital and is implemented in a standard complementary metal-oxide-semiconductor (CMOS) technology without any analog/RF or non-scalable components. It addresses the challenges that come along with continuous wide range of operation such as stability and phase frequency detection for a large frequency error range. A proposed multi-bit bidirectional smart shifter serves as the digitally controlled oscillator (DCO) control and tunes the DCO frequency by turning on/off inverter units in a large row/column matrix that constitute the ring oscillator. The smart shifter block is completely digital, consisting of standard cell logic gates, and is capable of tracking the row/column unit availability of the DCO and shifting multiple bits per single update cycle. This enables fast frequency acquisition times without necessitating dual loop fi lter or gear shifting mechanisms. The proposed ADPLL loop architecture does not employ costly, cumbersome DACs or binary to thermometer converters and minimizes loop filter and DCO control complexity. The wide range ADPLL is implemented in 90nm digital CMOS technology and has a 9-bit TDC, the output of which is processed by a 10-bit digital loop filter and a 5-bit smart shifter. In measurements, the synthesizer achieves 2.5GHz-7.3GHz operation while consuming 10mW/GHz power, with an active area of 0.23 mm2

An Energy-Efficient Reconfigurable Mobile Memory Interface for Computing Systems

The critical need for higher power efficiency and bandwidth transceiver design has significantly increased as mobile devices, such as smart phones, laptops, tablets, and ultra-portable personal digital assistants continue to be constructed using heterogeneous intellectual properties such as central processing units (CPUs), graphics processing units (GPUs), digital signal processors, dynamic random-access memories (DRAMs), sensors, and graphics/image processing units and to have enhanced graphic computing and video processing capabilities. However, the current mobile interface technologies which support CPU to memory communication (e.g. baseband-only signaling) have critical limitations, particularly super-linear energy consumption, limited bandwidth, and non-reconfigurable data access. As a consequence, there is a critical need to improve both energy efficiency and bandwidth for future mobile devices.;The primary goal of this study is to design an energy-efficient reconfigurable mobile memory interface for mobile computing systems in order to dramatically enhance the circuit and system bandwidth and power efficiency. The proposed energy efficient mobile memory interface which utilizes an advanced base-band (BB) signaling and a RF-band signaling is capable of simultaneous bi-directional communication and reconfigurable data access. It also increases power efficiency and bandwidth between mobile CPUs and memory subsystems on a single-ended shared transmission line. Moreover, due to multiple data communication on a single-ended shared transmission line, the number of transmission lines between mobile CPU and memories is considerably reduced, resulting in significant technological innovations, (e.g. more compact devices and low cost packaging to mobile communication interface) and establishing the principles and feasibility of technologies for future mobile system applications. The operation and performance of the proposed transceiver are analyzed and its circuit implementation is discussed in details. A chip prototype of the transceiver was implemented in a 65nm CMOS process technology. In the measurement, the transceiver exhibits higher aggregate data throughput and better energy efficiency compared to prior works

Integrated circuits for efficient power delivery using pulse-width-modulation

Circuits and architectures for efficient power delivery have become crucial in emerging smart systems. Switching power amplifiers (PA) are very attractive for such applications, because they exhibit better efficiency compared to linear PA designs, due to saturated operation. Switching PAs also allow for utilization of deep submicron CMOS technologies, due to which these designs can be easily integrated with digital circuits, and can benefit from process scaling, in performance as well as in area. Pulse-width-modulation (PWM) is commonly used with switching PAs. A PWM signal typically employs a high-frequency switching pulse waveform as a carrier signal, wherein the pulse-width or duty-cycle of each pulse is modulated by a given low-frequency input signal. The carrier frequency can vary from several kHz to GHz, and is typically determined by the target application. In this thesis, efficient power-delivery circuits that use PWM with switching class-D stages are presented. Advanced circuit techniques, as well as architectures for PWM are proposed to enhance efficiency and circumvent the limitations of conventional architectures. A digitally-intensive transmitter using RF-PWM with a class-D PA is described in the first part of the thesis. The use of carrier switching for alleviating the dynamic range limitation that can be observed in classical RF-PWM implementations is introduced. The approach employs the full carrier frequency for half of the amplitude range, and the second harmonic of half of the carrier frequency, for the remainder of the amplitude range. This concept not only allows the transmitter to drive modulated signals with large peak-to-average power ratio (PAPR), but also improves the back-off efficiency due to reduced switching losses in the half carrier-frequency mode. A glitch-free phase selector is proposed that removes the deleterious glitches that can occur at the input data transitions. The phase-selector also prevents D flip-flop setup-and-hold time violations. The transmitter has been implemented in a 130-nm CMOS process. The measured peak output power and power-added-efficiency (PAE) are 25.6 dBm and 34%, respectively. While driving 802.11g 20-MHz 64-QAM OFDM signals, the average measured output power is 18.3 dBm and the PAE is 16%, with an EVM of -25.5 dB. The second part of the thesis describes a high-speed driver that provides a PWM output using a class-D PA. A PLL-based architecture is employed which eliminates the requirement for a precise ramp or triangular signal generator, and a high-speed comparator, which are typically used for PWM generation. Multi-level signaling is proposed to enhance back-off as well as peak efficiency, which is critical for signals with high PAPR. A differential, folded PWM scheme is introduced to achieve highly linear operation. 3-level operation is achieved without the requirement for additional supply source or sink paths, while 5-level operation is achieved with additional supply source and sink paths, compared to 2-level operation. The PWM driver has been implemented in a 130-nm CMOS process and can operate with a switching frequency of 40-to-170 MHz. For 2/3/5-level PA operation, with a 500 kHz sinusoidal input and 60 MHz switching frequency, the measured THD is -61/-62/-53 dB and corresponding efficiency is 71/83/86% with 175/200/220 mW output power level, respectively. Performance has also been verified for 2/3-level PA operation with a high PAPR signal with 500 kHz bandwidth. While intended as a general purpose amplifier, the approach is well-suited for applications such as power-line communications (PLC). The final part of the thesis introduces an efficient buck/buck-boost reconfigurable LED driver that supports PWM and PFM operation. The driver is based on peak current control. Rectified sin as well as sin² functions are employed in the reference signal to improve the power factor (PF) and total harmonic distortion (THD) of the buck and buck-boost converters. The design ensures that the peak of the inductor current maintains a constant level that is invariant for different AC line voltages. The operating mode of the design can be changed between PWM and PFM. The LED driver has been implemented in a 130-nm CMOS process. PF and THD are improved when the proposed reference is employed, and peak PF and lowest THD are 0.995/0.983/0.996 and 7.8/6.2/3.5% for the buck (PWM), buck (PFM), buck-boost (PFM) cases, respectively. The corresponding peak efficiency for the three cases is 88/92/91%, respectively.Electrical and Computer Engineerin

Optimizing RF front ends for low power

This paper discusses optimizations for the power dissipation of RF front ends in portable wireless devices. A breakthrough in power dissipation can be achieved by simultaneously optimizing the antenna interface, circuits, and IC technology of such devices. A model that predicts the minimum power dissipation of a front end for both short-range and long-range connections will be introduced. Using these models, the impact of the antenna interface on the power dissipation will be assessed. Using two antennas with equal gain combining, a typical power dissipation reduction of 2.5 to 30 times can be achieved. Using high-impedance circuits for short-range systems in combination with silicon-on-anything technology, a further reduction of power dissipation by up to one order of magnitude can be realize

A Fully-Integrated Quad-Band GSM/GPRS CMOS Power Amplifier

Concentric distributed active transformers (DAT) are used to implement a fully-integrated quad-band power amplifier (PA) in a standard 130 nm CMOS process. The DAT enables the power amplifier to integrate the input and output matching networks on the same silicon die. The PA integrates on-chip closed-loop power control and operates under supply voltages from 2.9 V to 5.5 V in a standard micro-lead-frame package. It shows no oscillations, degradation, or failures for over 2000 hours of operation with a supply of 6 V at 135° under a VSWR of 15:1 at all phase angles and has also been tested for more than 2 million device-hours (with ongoing reliability monitoring) without a single failure under nominal operation conditions. It produces up to +35 dBm of RF power with power-added efficiency of 51%

Application and design manual for High Performance RF products

design work much easier NXP’s RF Manual – one of the most important reference tools on the market for today’s RF designers – features our complete range of RF products, from low to high power signal conditioning & high speed data converters. What’s new

Adaptive multibeam phased array design for a Spacelab experiment

The parametric tradeoff analyses and design for an Adaptive Multibeam Phased Array (AMPA) for a Spacelab experiment are described. This AMPA Experiment System was designed with particular emphasis to maximize channel capacity and minimize implementation and cost impacts for future austere maritime and aeronautical users, operating with a low gain hemispherical coverage antenna element, low effective radiated power, and low antenna gain-to-system noise temperature ratio

Low Power Cmos Circuit Design And Reliability Analysis For Wireless Me

A sensor node \u27AccuMicroMotion\u27 is proposed that has the ability to detect motion in 6 degrees of freedom for the application of physiological activity monitoring. It is expected to be light weight, low power, small and cheap. The sensor node may collect and transmit 3 axes of acceleration and 3 axes of angular rotation signals from MEMS transducers wirelessly to a nearby base station while attached to or implanted in human body. This dissertation proposes a wireless electronic system-on-a-single-chip to implement the sensor in a traditional CMOS process. The system is low power and may operate 50 hours from a single coin cell battery. A CMOS readout circuit, an analog to digital converter and a wireless transmitter is designed to implement the proposed system. In the architecture of the \u27AccuMicroMotion\u27 system, the readout circuit uses chopper stabilization technique and can resolve DC to 1 KHz and 200 nV signals from MEMS transducers. The base band signal is digitized using a 10-bit successive approximation register analog to digital converter. Digitized outputs from up to nine transducers can be combined in a parallel to serial converter for transmission by a 900 MHz RF transmitter that operates in amplitude shift keying modulation technique. The transmitter delivers a 2.2 mW power to a 50 Ù antenna. The system consumes an average current of 4.8 mA from a 3V supply when 6 sensors are in operation and provides an overall 60 dB dynamic range. Furthermore, in this dissertation, a methodology is developed that applies accelerated electrical stress on MOS devices to extract BSIM3 models and RF parameters through measurements to perform comprehensive study, analysis and modeling of several analog and RF circuits under hot carrier and breakdown degradation

Direct Digital Frequency Synthesizer Architecture for Wireless Communication in 90 NM CMOS Technology

Software radio is one promising field that can meet the demands for low cost, low power, and high speed electronic devices for wireless communication. At the heart of software radio is a programmable oscillator called a Direct Digital Synthesizer (DDS). DDS has the capabilities of rapid frequency hopping by digital software control while operating at very high frequencies and having sub-hertz resolution. Nevertheless, the digital-to-analog converter (DAC) and the read-only-memory (ROM) look-up table, building blocks of the DDS, prevent the DDS to be used in wireless communication because they introduce errors and noises to the DDS and their performances deteriorate at high speed. The DAC and ROM are replaced in this thesis by analog active filters that convert the square wave output of the phase accumulator directly into a sine wave. The proposed architecture operates with a reference clock of 9.09 GHz and can be fully-integrated in 90 nm CMOS technology