Accurate depth from defocus estimation with video-rate implementation

The science of measuring depth from images at video rate using „defocus‟ has been investigated. The method required two differently focussed images acquired from a single view point using a single camera. The relative blur between the images was used to determine the in-focus axial points of each pixel and hence depth. The depth estimation algorithm researched by Watanabe and Nayar was employed to recover the depth estimates, but the broadband filters, referred as the Rational filters were designed using a new procedure: the Two Step Polynomial Approach. The filters designed by the new model were largely insensitive to object texture and were shown to model the blur more precisely than the previous method. Experiments with real planar images demonstrated a maximum RMS depth error of 1.18% for the proposed filters, compared to 1.54% for the previous design. The researched software program required five 2D convolutions to be processed in parallel and these convolutions were effectively implemented on a FPGA using a two channel, five stage pipelined architecture, however the precision of the filter coefficients and the variables had to be limited within the processor. The number of multipliers required for each convolution was reduced from 49 to 10 (79.5% reduction) using a Triangular design procedure. Experimental results suggested that the pipelined processor provided depth estimates comparable in accuracy to the full precision Matlab‟s output, and generated depth maps of size 400 x 400 pixels in 13.06msec, that is faster than the video rate. The defocused images (near and far-focused) were optically registered for magnification using Telecentric optics. A frequency domain approach based on phase correlation was employed to measure the radial shifts due to magnification and also to optimally position the external aperture. The telecentric optics ensured pixel to pixel registration between the defocused images was correct and provided more accurate depth estimates

Computational Imaging Approach to Recovery of Target Coordinates Using Orbital Sensor Data

This dissertation addresses the components necessary for simulation of an image-based recovery of the position of a target using orbital image sensors. Each component is considered in detail, focusing on the effect that design choices and system parameters have on the accuracy of the position estimate. Changes in sensor resolution, varying amounts of blur, differences in image noise level, selection of algorithms used for each component, and lag introduced by excessive processing time all contribute to the accuracy of the result regarding recovery of target coordinates using orbital sensor data. Using physical targets and sensors in this scenario would be cost-prohibitive in the exploratory setting posed, therefore a simulated target path is generated using Bezier curves which approximate representative paths followed by the targets of interest. Orbital trajectories for the sensors are designed on an elliptical model representative of the motion of physical orbital sensors. Images from each sensor are simulated based on the position and orientation of the sensor, the position of the target, and the imaging parameters selected for the experiment (resolution, noise level, blur level, etc.). Post-processing of the simulated imagery seeks to reduce noise and blur and increase resolution. The only information available for calculating the target position by a fully implemented system are the sensor position and orientation vectors and the images from each sensor. From these data we develop a reliable method of recovering the target position and analyze the impact on near-realtime processing. We also discuss the influence of adjustments to system components on overall capabilities and address the potential system size, weight, and power requirements from realistic implementation approaches

Coded aperture imaging

This thesis studies the coded aperture camera, a device consisting of a conventional camera with a modified aperture mask, that enables the recovery of both depth map and all-in-focus image from a single 2D input image. Key contributions of this work are the modeling of the statistics of natural images and the design of efficient blur identification methods in a Bayesian framework. Two cases are distinguished: 1) when the aperture can be decomposed in a small set of identical holes, and 2) when the aperture has a more general configuration. In the first case, the formulation of the problem incorporates priors about the statistical variation of the texture to avoid ambiguities in the solution. This allows to bypass the recovery of the sharp image and concentrate only on estimating depth. In the second case, the depth reconstruction is addressed via convolutions with a bank of linear filters. Key advantages over competing methods are the higher numerical stability and the ability to deal with large blur. The all-in-focus image can then be recovered by using a deconvolution step with the estimated depth map. Furthermore, for the purpose of depth estimation alone, the proposed algorithm does not require information about the mask in use. The comparison with existing algorithms in the literature shows that the proposed methods achieve state-of-the-art performance. This solution is also extended for the first time to images affected by both defocus and motion blur and, finally, to video sequences with moving and deformable objects

Subspace Representations for Robust Face and Facial Expression Recognition

Analyzing human faces and modeling their variations have always been of interest to the computer vision community. Face analysis based on 2D intensity images is a challenging problem, complicated by variations in pose, lighting, blur, and non-rigid facial deformations due to facial expressions. Among the different sources of variation, facial expressions are of interest as important channels of non-verbal communication. Facial expression analysis is also affected by changes in view-point and inter-subject variations in performing different expressions. This dissertation makes an attempt to address some of the challenges involved in developing robust algorithms for face and facial expression recognition by exploiting the idea of proper subspace representations for data. Variations in the visual appearance of an object mostly arise due to changes in illumination and pose. So we first present a video-based sequential algorithm for estimating the face albedo as an illumination-insensitive signature for face recognition. We show that by knowing/estimating the pose of the face at each frame of a sequence, the albedo can be efficiently estimated using a Kalman filter. Then we extend this to the case of unknown pose by simultaneously tracking the pose as well as updating the albedo through an efficient Bayesian inference method performed using a Rao-Blackwellized particle filter. Since understanding the effects of blur, especially motion blur, is an important problem in unconstrained visual analysis, we then propose a blur-robust recognition algorithm for faces with spatially varying blur. We model a blurred face as a weighted average of geometrically transformed instances of its clean face. We then build a matrix, for each gallery face, whose column space spans the space of all the motion blurred images obtained from the clean face. This matrix representation is then used to define a proper objective function and perform blur-robust face recognition. To develop robust and generalizable models for expression analysis one needs to break the dependence of the models on the choice of the coordinate frame of the camera. To this end, we build models for expressions on the affine shape-space (Grassmann manifold), as an approximation to the projective shape-space, by using a Riemannian interpretation of deformations that facial expressions cause on different parts of the face. This representation enables us to perform various expression analysis and recognition algorithms without the need for pose normalization as a preprocessing step. There is a large degree of inter-subject variations in performing various expressions. This poses an important challenge on developing robust facial expression recognition algorithms. To address this challenge, we propose a dictionary-based approach for facial expression analysis by decomposing expressions in terms of action units (AUs). First, we construct an AU-dictionary using domain experts' knowledge of AUs. To incorporate the high-level knowledge regarding expression decomposition and AUs, we then perform structure-preserving sparse coding by imposing two layers of grouping over AU-dictionary atoms as well as over the test image matrix columns. We use the computed sparse code matrix for each expressive face to perform expression decomposition and recognition. Most of the existing methods for the recognition of faces and expressions consider either the expression-invariant face recognition problem or the identity-independent facial expression recognition problem. We propose joint face and facial expression recognition using a dictionary-based component separation algorithm (DCS). In this approach, the given expressive face is viewed as a superposition of a neutral face component with a facial expression component, which is sparse with respect to the whole image. This assumption leads to a dictionary-based component separation algorithm, which benefits from the idea of sparsity and morphological diversity. The DCS algorithm uses the data-driven dictionaries to decompose an expressive test face into its constituent components. The sparse codes we obtain as a result of this decomposition are then used for joint face and expression recognition

Multispectral image alignment using a three channel endoscope in vivo during minimally invasive surgery.

Sequential multispectral imaging is an acquisition technique that involves collecting images of a target at different wavelengths, to compile a spectrum for each pixel. In surgical applications it suffers from low illumination levels and motion artefacts. A three-channel rigid endoscope system has been developed that allows simultaneous recording of stereoscopic and multispectral images. Salient features on the tissue surface may be tracked during the acquisition in the stereo cameras and, using multiple camera triangulation techniques, this information used to align the multispectral images automatically even though the tissue or camera is moving. This paper describes a detailed validation of the set-up in a controlled experiment before presenting the first in vivo use of the device in a porcine minimally invasive surgical procedure. Multispectral images of the large bowel were acquired and used to extract the relative concentration of haemoglobin in the tissue despite motion due to breathing during the acquisition. Using the stereoscopic information it was also possible to overlay the multispectral information on the reconstructed 3D surface. This experiment demonstrates the ability of this system for measuring blood perfusion changes in the tissue during surgery and its potential use as a platform for other sequential imaging modalities

Recent Progress in Image Deblurring

This paper comprehensively reviews the recent development of image deblurring, including non-blind/blind, spatially invariant/variant deblurring techniques. Indeed, these techniques share the same objective of inferring a latent sharp image from one or several corresponding blurry images, while the blind deblurring techniques are also required to derive an accurate blur kernel. Considering the critical role of image restoration in modern imaging systems to provide high-quality images under complex environments such as motion, undesirable lighting conditions, and imperfect system components, image deblurring has attracted growing attention in recent years. From the viewpoint of how to handle the ill-posedness which is a crucial issue in deblurring tasks, existing methods can be grouped into five categories: Bayesian inference framework, variational methods, sparse representation-based methods, homography-based modeling, and region-based methods. In spite of achieving a certain level of development, image deblurring, especially the blind case, is limited in its success by complex application conditions which make the blur kernel hard to obtain and be spatially variant. We provide a holistic understanding and deep insight into image deblurring in this review. An analysis of the empirical evidence for representative methods, practical issues, as well as a discussion of promising future directions are also presented.Comment: 53 pages, 17 figure

Accurate depth from defocus estimation with video-rate implementation

The science of measuring depth from images at video rate using „defocus‟ has been investigated. The method required two differently focussed images acquired from a single view point using a single camera. The relative blur between the images was used to determine the in-focus axial points of each pixel and hence depth. The depth estimation algorithm researched by Watanabe and Nayar was employed to recover the depth estimates, but the broadband filters, referred as the Rational filters were designed using a new procedure: the Two Step Polynomial Approach. The filters designed by the new model were largely insensitive to object texture and were shown to model the blur more precisely than the previous method. Experiments with real planar images demonstrated a maximum RMS depth error of 1.18% for the proposed filters, compared to 1.54% for the previous design. The researched software program required five 2D convolutions to be processed in parallel and these convolutions were effectively implemented on a FPGA using a two channel, five stage pipelined architecture, however the precision of the filter coefficients and the variables had to be limited within the processor. The number of multipliers required for each convolution was reduced from 49 to 10 (79.5% reduction) using a Triangular design procedure. Experimental results suggested that the pipelined processor provided depth estimates comparable in accuracy to the full precision Matlab‟s output, and generated depth maps of size 400 x 400 pixels in 13.06msec, that is faster than the video rate. The defocused images (near and far-focused) were optically registered for magnification using Telecentric optics. A frequency domain approach based on phase correlation was employed to measure the radial shifts due to magnification and also to optimally position the external aperture. The telecentric optics ensured pixel to pixel registration between the defocused images was correct and provided more accurate depth estimates.EThOS - Electronic Theses Online ServiceUniversity of Warwick (UoW)GBUnited Kingdo

Model-driven and Data-driven Approaches for some Object Recognition Problems

Recognizing objects from images and videos has been a long standing problem in computer vision. The recent surge in the prevalence of visual cameras has given rise to two main challenges where, (i) it is important to understand different sources of object variations in more unconstrained scenarios, and (ii) rather than describing an object in isolation, efficient learning methods for modeling object-scene `contextual' relations are required to resolve visual ambiguities. This dissertation addresses some aspects of these challenges, and consists of two parts. First part of the work focuses on obtaining object descriptors that are largely preserved across certain sources of variations, by utilizing models for image formation and local image features. Given a single instance of an object, we investigate the following three problems. (i) Representing a 2D projection of a 3D non-planar shape invariant to articulations, when there are no self-occlusions. We propose an articulation invariant distance that is preserved across piece-wise affine transformations of a non-rigid object `parts', under a weak perspective imaging model, and then obtain a shape context-like descriptor to perform recognition; (ii) Understanding the space of `arbitrary' blurred images of an object, by representing an unknown blur kernel of a known maximum size using a complete set of orthonormal basis functions spanning that space, and showing that subspaces resulting from convolving a clean object and its blurred versions with these basis functions are equal under some assumptions. We then view the invariant subspaces as points on a Grassmann manifold, and use statistical tools that account for the underlying non-Euclidean nature of the space of these invariants to perform recognition across blur; (iii) Analyzing the robustness of local feature descriptors to different illumination conditions. We perform an empirical study of these descriptors for the problem of face recognition under lighting change, and show that the direction of image gradient largely preserves object properties across varying lighting conditions. The second part of the dissertation utilizes information conveyed by large quantity of data to learn contextual information shared by an object (or an entity) with its surroundings. (i) We first consider a supervised two-class problem of detecting lane markings from road video sequences, where we learn relevant feature-level contextual information through a machine learning algorithm based on boosting. We then focus on unsupervised object classification scenarios where, (ii) we perform clustering using maximum margin principles, by deriving some basic properties on the affinity of `a pair of points' belonging to the same cluster using the information conveyed by `all' points in the system, and (iii) then consider correspondence-free adaptation of statistical classifiers across domain shifting transformations, by generating meaningful `intermediate domains' that incrementally convey potential information about the domain change