22 research outputs found
Interface Circuits for Microsensor Integrated Systems
ca. 200 words; this text will present the book in all promotional forms (e.g. flyers). Please describe the book in straightforward and consumer-friendly terms. [Recent advances in sensing technologies, especially those for Microsensor Integrated Systems, have led to several new commercial applications. Among these, low voltage and low power circuit architectures have gained growing attention, being suitable for portable long battery life devices. The aim is to improve the performances of actual interface circuits and systems, both in terms of voltage mode and current mode, in order to overcome the potential problems due to technology scaling and different technology integrations. Related problems, especially those concerning parasitics, lead to a severe interface design attention, especially concerning the analog front-end and novel and smart architecture must be explored and tested, both at simulation and prototype level. Moreover, the growing demand for autonomous systems gets even harder the interface design due to the need of energy-aware cost-effective circuit interfaces integrating, where possible, energy harvesting solutions. The objective of this Special Issue is to explore the potential solutions to overcome actual limitations in sensor interface circuits and systems, especially those for low voltage and low power Microsensor Integrated Systems. The present Special Issue aims to present and highlight the advances and the latest novel and emergent results on this topic, showing best practices, implementations and applications. The Guest Editors invite to submit original research contributions dealing with sensor interfacing related to this specific topic. Additionally, application oriented and review papers are encouraged.
Data acquisition techniques based on frequency-encoding applied to capacitive MEMS microphones
Mención Internacional en el título de doctorThis thesis focuses on the development of capacitive sensor readout circuits
and data converters based on frequency-encoding. This research
has been motivated by the needs of consumer electronics industry, which
constantly demands more compact readout circuit for MEMS microphones
and other sensors. Nowadays, data acquisition is mainly based
on encoding signals in voltage or current domains, which is becoming
more challenging in modern deep submicron CMOS technologies.
Frequency-encoding is an emerging signal processing technique based
on encoding signals in the frequency domain. The key advantage of
this approach is that systems can be implemented using mostly-digital
circuitry, which benefits from CMOS technology scaling. Frequencyencoding
can be used to build phase referenced integrators, which can
replace classical integrators (such as switched-capacitor based integrators)
in the implementation of efficient analog-to-digital converters and
sensor interfaces. The core of the phase referenced integrators studied in
this thesis consists of the combination of different oscillator topologies
with counters and highly-digital circuitry.
This work addresses two related problems: the development of capacitive
MEMS sensor readout circuits based on frequency-encoding, and the
design and implementation of compact oscillator-based data converters
for audio applications.
In the first problem, the target is the integration of the MEMS sensor
into an oscillator circuit, making the oscillation frequency dependent on
the sensor capacitance. This way, the sound can be digitized by measuring
the oscillation frequency, using digital circuitry. However, a MEMS
microphone is a complex structure on which several parasitic effects can
influence the operation of the oscillator. This work presents a feasibility
analysis of the integration of a MEMS microphone into different oscillator
topologies. The conclusion of this study is that the parasitics of the
MEMS limit the performance of the microphone, making it inefficient.
In contrast, replacing conventional ADCs with frequency-encoding based
ADCs has proven a very efficient solution, which motivates the next
problem.
In the second problem, the focus is on the development of high-order
oscillator-based Sigma-Delta modulators. Firstly, the equivalence between classical
integrators and phase referenced integrators has been studied, followed
by an overview of state-of-art oscillator-based converters. Then,
a procedure to replace classical integrators by phase referenced integrators
is presented, including a design example of a second-order oscillator based
Sigma-Delta modulator. Subsequently, the main circuit impairments that
limit the performance of this kind of implementations, such as phase
noise, jitter or metastability, are described.
This thesis also presents a methodology to evaluate the impact of
phase noise and distortion in oscillator-based systems. The proposed
method is based on periodic steady-state analysis, which allows the rapid
estimation of the system dynamic range without resorting to transient
simulations. In addition, a novel technique to analyze the impact of
clock jitter in Sigma-Delta modulators is described.
Two integrated circuits have been implemented in 0.13 μm CMOS
technology to demonstrate the feasibility of high-order oscillator-based Sigma-Delta modulators. Both chips have been designed to feature secondorder
noise shaping using only oscillators and digital circuitry. The first
testchip shows a malfunction in the digital circuitry due to the complexity
of the multi-bit counters. The second chip, implemented using
single-bit counters for simplicity, shows second-order noise shaping and
reaches 103 dB-A of dynamic range in the audio bandwidth, occupying
only 0.04 mm2.Esta tesis se centra en el desarrollo de conversores de datos e interfaces
para sensores capacitivos basados en codificación en frecuencia. Esta
investigación está motivada por las necesidades de la industria, que constantemente
demanda reducir el tamaño de este tipo de circuitos. Hoy en
día, la adquisición de datos está basada principalmente en la codificación
de señales en tensión o en corriente. Sin embargo, la implementación
de este tipo de soluciones en tecnologías CMOS nanométricas presenta
varias dificultades.
La codificación de frecuencia es una técnica emergente en el procesado
de señales basada en codificar señales en el dominio de la frecuencia.
La principal ventaja de esta alternativa es que los sistemas pueden implementarse
usando circuitos mayoritariamente digitales, los cuales se
benefician de los avances de la tecnología CMOS. La codificación en
frecuencia puede emplearse para construir integradores referidos a la
fase, que pueden reemplazar a los integradores clásicos (como los basados
en capacidades conmutadas) en la implementación de conversores
analógico-digital e interfaces de sensores. Los integradores referidos a la
fase estudiados en esta tesis consisten en la combinación de diferentes
topologías de osciladores con contadores y circuitos principalmente digitales.
Este trabajo aborda dos cuestiones relacionadas: el desarrollo de circuitos
de lectura para sensores MEMS capacitivos basados en codificación
temporal, y el diseño e implementación de conversores de datos
compactos para aplicaciones de audio basados en osciladores.
En el primer caso, el objetivo es la integración de un sensor MEMS
en un oscilador, haciendo que la frecuencia de oscilación depe capacidad del sensor. De esta forma, el sonido puede ser digitalizado
midiendo la frecuencia de oscilación, lo cual puede realizarse usando circuitos
en su mayor parte digitales. Sin embargo, un micrófono MEMS es
una estructura compleja en la que múltiples efectos parasíticos pueden
alterar el correcto funcionamiento del oscilador. Este trabajo presenta
un análisis de la viabilidad de integrar un micrófono MEMS en diferentes
topologías de oscilador. La conclusión de este estudio es que los parasíticos
del MEMS limitan el rendimiento del micrófono, causando que esta
solución no sea eficiente. En cambio, la implementación de conversores
analógico-digitales basados en codificación en frecuencia ha demostrado
ser una alternativa muy eficiente, lo cual motiva el estudio del siguiente
problema.
La segunda cuestión está centrada en el desarrollo de moduladores Sigma-Delta de alto orden basados en osciladores. En primer lugar se ha estudiado
la equivalencia entre los integradores clásicos y los integradores
referidos a la fase, seguido de una descripción de los conversores basados
en osciladores publicados en los últimos años. A continuación se
presenta un procedimiento para reemplazar integradores clásicos por integradores
referidos a la fase, incluyendo un ejemplo de diseño de un
modulador Sigma-Delta de segundo orden basado en osciladores. Posteriormente
se describen los principales problemas que limitan el rendimiento de este
tipo de sistemas, como el ruido de fase, el jitter o la metaestabilidad.
Esta tesis también presenta un nuevo método para evaluar el impacto
del ruido de fase y de la distorsión en sistemas basados en osciladores. El
método propuesto está basado en simulaciones PSS, las cuales permiten
la rápida estimación del rango dinámico del sistema sin necesidad de
recurrir a simulaciones temporales. Además, este trabajo describe una
nueva técnica para analizar el impacto del jitter de reloj en moduladores Sigma-Delta.
En esta tesis se han implementado dos circuitos integrados en tecnología
CMOS de 0.13 μm, con el fin de demostrar la viabilidad de los
moduladores Sigma-Delta de alto orden basados en osciladores. Ambos chips han
sido diseñados para producir conformación espectral de ruido de segundo
orden, usando únicamente osciladores y circuitos mayoritariamente digitales.
El primer chip ha mostrado un error en el funcionamiento de los
circuitos digitales debido a la complejidad de las estructuras multi-bit
utilizadas. El segundo chip, implementado usando contadores de un solo
bit con el fin de simplificar el sistema, consigue conformación espectral
de ruido de segundo orden y alcanza 103 dB-A de rango dinámico en el
ancho de banda del audio, ocupando solo 0.04 mm2.Programa Oficial de Doctorado en Ingeniería Eléctrica, Electrónica y AutomáticaPresidente: Georges G.E. Gielen.- Secretario: José Manuel de la Rosa.- Vocal: Ana Rus
Ultra-low-power circuits and systems for wearable and implantable medical devices
Thesis (Ph. D.)--Massachusetts Institute of Technology, Department of Electrical Engineering and Computer Science, 2013.Cataloged from PDF version of thesis.Includes bibliographical references (pages 219-231).Advances in circuits, sensors, and energy storage elements have opened up many new possibilities in the health industry. In the area of wearable devices, the miniaturization of electronics has spurred the rapid development of wearable vital signs, activity, and fitness monitors. Maximizing the time between battery recharge places stringent requirements on power consumption by the device. For implantable devices, the situation is exacerbated by the fact that energy storage capacity is limited by volume constraints, and frequent battery replacement via surgery is undesirable. In this case, the design of energy-efficient circuits and systems becomes even more crucial. This thesis explores the design of energy-efficient circuits and systems for two medical applications. The first half of the thesis focuses on the design and implementation of an ultra-low-power, mixed-signal front-end for a wearable ECG monitor in a 0.18pm CMOS process. A mixed-signal architecture together with analog circuit optimizations enable ultra-low-voltage operation at 0.6V which provides power savings through voltage scaling, and ensures compatibility with state-of-the-art DSPs. The fully-integrated front-end consumes just 2.9[mu]W, which is two orders of magnitude lower than commercially available parts. The second half of this thesis focuses on ultra-low-power system design and energy-efficient neural stimulation for a proof-of-concept fully-implantable cochlear implant. First, implantable acoustic sensing is demonstrated by sensing the motion of a human cadaveric middle ear with a piezoelectric sensor. Second, alternate energy-efficient electrical stimulation waveforms are investigated to reduce neural stimulation power when compared to the conventional rectangular waveform. The energy-optimal waveform is analyzed using a computational nerve fiber model, and validated with in-vivo ECAP recordings in the auditory nerve of two cats and with psychophysical tests in two human cochlear implant users. Preliminary human subject testing shows that charge and energy savings of 20-30% and 15-35% respectively are possible with alternative waveforms. A system-on-chip comprising the sensor interface, reconfigurable sound processor, and arbitrary-waveform neural stimulator is implemented in a 0.18[mu]m high-voltage CMOS process to demonstrate the feasibility of this system. The sensor interface and sound processor consume just 12[mu]W of power, representing just 2% of the overall system power which is dominated by stimulation. As a result, the energy savings from using alternative stimulation waveforms transfer directly to the system.by Marcus Yip.Ph.D
Research and Technology, 1998
This report selectively summarizes the NASA Lewis Research Center's research and technology accomplishments for the fiscal year 1998. It comprises 134 short articles submitted by the staff scientists and engineers. The report is organized into five major sections: Aeronautics, Research and Technology, Space, Engineering and Technical Services, and Commercial Technology. A table of contents and an author index have been developed to assist readers in finding articles of special interest. This report is not intended to he a comprehensive summary of all the research and technology work done over the past fiscal year. Most of the work is reported in Lewis-published technical reports, journal articles, and presentations prepared by Lewis staff and contractors. In addition, university grants have enabled faculty members and graduate students to engage in sponsored research that is reported at technical meetings or in journal articles. For each article in this report, a Lewis contact person has been identified, and where possible, reference documents are listed so that additional information can be easily obtained. The diversity of topics attests to the breadth of research and technology being pursued and to the skill mix of the staff that makes it possible. At the time of publication, NASA Lewis was undergoing a name change to the NASA John H. Glenn Research Center at Lewis Field
Recommended from our members
Ultra-Low-Power Sensors and Receivers for IoT Applications
The combination of ultra-low power analog front-ends and CMOS-compatible transducers enable new applications, such as environmental monitors, household appliances, health trackers, etc. that are seamlessly integrated into our daily lives. Furthermore, wireless connectivity allows many of these sensors to operate both independently and collectively. These techniques collectively fulfil the recent surge of internet-of-things (IoT) applications that have the potential to fundamentally change daily life for millions of people.In this dissertation, the circuit and system design of wireless receivers and sensors is presented that explores the challenges of implementing long lifespan, high accuracy, and large coverage range IoT sensor networks. The first is a wake-up receiver (WuRX), which continuously monitors the RF environment to wake up a higher-power radio upon detection of a predetermined RF signature. This work both improves sensitivity and reduces power over prior art through a multi-faceted design featuring an impedance transformation network with large passive voltage gain, an active envelope detector with high input impedance to facilitate large passive voltage gain, a low-power precision comparator, and a low-leakage digital baseband correlator.Although pushing the prior WuRX performance boundary by orders of magnitude, the first work shows moderate sensitivity, inferior temperature robustness, and large area with external lumped components. Thus, the second work shows a miniaturized WuRX that is temperature-compensated, yet still consumes only nano-watt power and millimeter area while operating at 9 GHz. To further reduce the area, a global common-mode feedback is utilized across the envelope detector and baseband amplifier that eliminates the need for off-chip ac-coupling components. Multiple temperature-compensation techniques are proposed to maintain constant bandwidth of the signal path and constant clock frequency. Both WuRXs operate at 0.4 V supply, consume near-zero power and achieve ~-70 dBm sensitivity.Lastly, the first reported CMOS 2-in-1 relative humidity and temperature sensor is presented. A unified analog front-end interfaces on-chip transducers and converts the inputs into a frequency vis a high-linearity frequency-locked loop. An incomplete-settling switched-capacitor-based Wheatstone bridge is proposed to sense the inputs in a power-efficient fashion
Asynchronous spike event coding scheme for programmable analogue arrays and its computational applications
This work is the result of the definition, design and evaluation of a novel method to interconnect
the computational elements - commonly known as Configurable Analogue Blocks (CABs) - of
a programmable analogue array. This method is proposed for total or partial replacement of the
conventional methods due to serious limitations of the latter in terms of scalability.
With this method, named Asynchronous Spike Event Coding (ASEC) scheme, analogue signals
from CABs outputs are encoded as time instants (spike events) dependent upon those signals
activity and are transmitted asynchronously by employing the Address Event Representation
(AER) protocol. Power dissipation is dependent upon input signal activity and no spike events
are generated when the input signal is constant.
On-line, programmable computation is intrinsic to ASEC scheme and is performed without additional
hardware. The ability of the communication scheme to perform computation enhances
the computation power of the programmable analogue array. The design methodology and a
CMOS implementation of the scheme are presented together with test results from prototype
integrated circuits (ICs)
Solid State Circuits Technologies
The evolution of solid-state circuit technology has a long history within a relatively short period of time. This technology has lead to the modern information society that connects us and tools, a large market, and many types of products and applications. The solid-state circuit technology continuously evolves via breakthroughs and improvements every year. This book is devoted to review and present novel approaches for some of the main issues involved in this exciting and vigorous technology. The book is composed of 22 chapters, written by authors coming from 30 different institutions located in 12 different countries throughout the Americas, Asia and Europe. Thus, reflecting the wide international contribution to the book. The broad range of subjects presented in the book offers a general overview of the main issues in modern solid-state circuit technology. Furthermore, the book offers an in depth analysis on specific subjects for specialists. We believe the book is of great scientific and educational value for many readers. I am profoundly indebted to the support provided by all of those involved in the work. First and foremost I would like to acknowledge and thank the authors who worked hard and generously agreed to share their results and knowledge. Second I would like to express my gratitude to the Intech team that invited me to edit the book and give me their full support and a fruitful experience while working together to combine this book
NASA Tech Briefs, April 2000
Topics covered include: Imaging/Video/Display Technology; Electronic Components and Circuits; Electronic Systems; Physical Sciences; Materials; Computer Programs; Mechanics; Bio-Medical; Test and Measurement; Mathematics and Information Sciences; Books and Reports
Optoelectronics – Devices and Applications
Optoelectronics - Devices and Applications is the second part of an edited anthology on the multifaced areas of optoelectronics by a selected group of authors including promising novices to experts in the field. Photonics and optoelectronics are making an impact multiple times as the semiconductor revolution made on the quality of our life. In telecommunication, entertainment devices, computational techniques, clean energy harvesting, medical instrumentation, materials and device characterization and scores of other areas of R&D the science of optics and electronics get coupled by fine technology advances to make incredibly large strides. The technology of light has advanced to a stage where disciplines sans boundaries are finding it indispensable. New design concepts are fast emerging and being tested and applications developed in an unimaginable pace and speed. The wide spectrum of topics related to optoelectronics and photonics presented here is sure to make this collection of essays extremely useful to students and other stake holders in the field such as researchers and device designers