On-Chip Transparent Wire Pipelining (invited paper)

Wire pipelining has been proposed as a viable mean to break the discrepancy between decreasing gate delays and increasing wire delays in deep-submicron technologies. Far from being a straightforwardly applicable technique, this methodology requires a number of design modifications in order to insert it seamlessly in the current design flow. In this paper we briefly survey the methods presented by other researchers in the field and then we thoroughly analyze the solutions we recently proposed, ranging from system-level wire pipelining to physical design aspects

Automated Debugging Methodology for FPGA-based Systems

Electronic devices make up a vital part of our lives. These are seen from mobiles, laptops, computers, home automation, etc. to name a few. The modern designs constitute billions of transistors. However, with this evolution, ensuring that the devices fulfill the designer’s expectation under variable conditions has also become a great challenge. This requires a lot of design time and effort. Whenever an error is encountered, the process is re-started. Hence, it is desired to minimize the number of spins required to achieve an error-free product, as each spin results in loss of time and effort. Software-based simulation systems present the main technique to ensure the verification of the design before fabrication. However, few design errors (bugs) are likely to escape the simulation process. Such bugs subsequently appear during the post-silicon phase. Finding such bugs is time-consuming due to inherent invisibility of the hardware. Instead of software simulation of the design in the pre-silicon phase, post-silicon techniques permit the designers to verify the functionality through the physical implementations of the design. The main benefit of the methodology is that the implemented design in the post-silicon phase runs many order-of-magnitude faster than its counterpart in pre-silicon. This allows the designers to validate their design more exhaustively. This thesis presents five main contributions to enable a fast and automated debugging solution for reconfigurable hardware. During the research work, we used an obstacle avoidance system for robotic vehicles as a use case to illustrate how to apply the proposed debugging solution in practical environments. The first contribution presents a debugging system capable of providing a lossless trace of debugging data which permits a cycle-accurate replay. This methodology ensures capturing permanent as well as intermittent errors in the implemented design. The contribution also describes a solution to enhance hardware observability. It is proposed to utilize processor-configurable concentration networks, employ debug data compression to transmit the data more efficiently, and partially reconfiguring the debugging system at run-time to save the time required for design re-compilation as well as preserve the timing closure. The second contribution presents a solution for communication-centric designs. Furthermore, solutions for designs with multi-clock domains are also discussed. The third contribution presents a priority-based signal selection methodology to identify the signals which can be more helpful during the debugging process. A connectivity generation tool is also presented which can map the identified signals to the debugging system. The fourth contribution presents an automated error detection solution which can help in capturing the permanent as well as intermittent errors without continuous monitoring of debugging data. The proposed solution works for designs even in the absence of golden reference. The fifth contribution proposes to use artificial intelligence for post-silicon debugging. We presented a novel idea of using a recurrent neural network for debugging when a golden reference is present for training the network. Furthermore, the idea was also extended to designs where golden reference is not present

Imperfection-Aware Design of CNFET Digital VLSI Circuits

Carbon nanotube field-effect transistor (CNFET) is one of the promising candidates as extensions to silicon CMOS devices. The CNFET, which is a 1-D structure with a near-ballistic transport capability, can potentially offer excellent device characteristics and order-of-magnitude better energy-delay product over standard CMOS devices. Significant challenges in CNT synthesis prevent CNFETs today from achieving such ideal benefits. CNT density variation and metallic CNTs are the dominant type of CNT variations/imperfections that cause performance variation, large static power consumption, and yield degradation. We present an imperfection-aware design technique for CNFET digital VLSI circuits by: 1) Analytical models that are developed to analyze and quantify the effects of CNT density variation on device characteristics, gate and system levels delays. The analytical models, which were validated by comparison to real experimental/simulation data, enables us to examine the space of CNFET combinational, sequential and memory cells circuits to minimize delay variations. Using these model, we drive CNFET processing and circuit design guidelines to manage/overcome CNT density variation. 2) Analytical models that are developed to analyze the effects of metallic CNTs on device characteristics, gate and system levels delay and power consumption. Using our presented analytical models, which are again validated by comparison with simulation data, it is shown that the static power dissipation is a more critical issue than the delay and the dynamic power of CNFET circuits in the presence of m-CNTs. 3) CNT density variation and metallic CNTs can result in functional failure of CNFET circuits. The complete and compact model for CNFET probability of failure that consider CNT density variation and m-CNTs is presented. This analytical model is applied to analyze the logical functional failures. The presented model is extended to predict opportunities and limitations of CNFET technology at todays Gigascale integration and beyond.\u2

정적 램 및 파워 게이트 회로에 대한 전압 및 보존용 공간 할당 문제

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2021.8. 김태환.칩의 저전력 동작은 중요한 문제이며, 공정이 발전하면서 그 중요성은 점점 커지고 있다. 본 논문은 칩을 구성하는 정적 램(SRAM) 및 로직(logic) 각각에 대해서 저전력으로 동작시키는 방법론을 논한다. 우선, 본 논문에서는 칩을 문턱 전압 근처의 전압(NTV)에서 동작시키고자 할 때 모니터링 회로의 측정을 통해 칩 내의 모든 SRAM 블록에서 동작 실패가 발생하지 않는 최소 동작 전압을 추론하는 방법론을 제안한다. 칩을 NTV 영역에서 동작시키는 것은 에너지 효율성을 증대시킬 수 있는 매우 효과적인 방법 중 하나이지만 SRAM의 경우 동작 실패 때문에 동작 전압을 낮추기 어렵다. 하지만 칩마다 영향을 받는 공정 변이가 다르므로 최소 동작 전압은 칩마다 다르며, 모니터링을 통해 이를 추론해낼 수 있다면 칩별로 SRAM에 서로 다른 전압을 인가해 에너지 효율성을 높일 수 있다. 본 논문에서는 다음과 같은 과정을 통해 이 문제를 해결한다: (1) 디자인 인프라 설계 단계에서는 SRAM의 최소 동작 전압을 추론하고 칩 생산 단계에서는 SRAM 모니터의 측정을 통해 전압을 인가하는 방법론을 제안한다; (2) 칩의 SRAM 비트셀(bitcell)과 주변 회로를 포함한 SRAM 블록들의 공정 변이를 모니터링할 수 있는 SRAM 모니터와 SRAM 모니터에서 모니터링할 대상을 정의한다; (3) SRAM 모니터의 측정값을 이용해 같은 칩에 존재하는 모든 SRAM 블록에서 목표 신뢰수준 내에서 읽기, 쓰기, 및 접근 동작 실패가 발생하지 않는 최소 동작 전압을 추론한다. 벤치마크 회로의 실험 결과는 본 논문에서 제안한 방법을 따라 칩별로 SRAM 블록들의 최소 동작 전압을 다르게 인가할 경우, 기존 방법대로 모든 칩에 동일한 전압을 인가하는 것 대비 수율은 같은 수준으로 유지하면서 SRAM 비트셀 배열의 전력 소모를 감소시킬 수 있음을 보인다. 두 번째로, 본 논문에서는 파워 게이트 회로에서 기존의 보존용 공간 할당 방법들이 지니고 있는 문제를 해결하고 누설 전력 소모를 더 줄일 수 있는 방법론을 제안한다. 기존의 보존용 공간 할당 방법은 멀티플렉서 피드백 루프가 있는 모든 플립플롭에는 무조건 보존용 공간을 할당해야 해야 하기 때문에 다중 비트 보존용 공간의 장점을 충분히 살리지 못하는 문제가 있다. 본 논문에서는 다음과 같은 방법을 통해 보존용 공간을 최소화하는 문제를 해결한다: (1) 보존용 공간 할당 과정에서 멀티플렉서 피드백 루프를 무시할 수 있는 조건을 제시하고, (2) 해당 조건을 이용해 멀티플렉서 피드백 루프가 있는 플립플롭이 많이 존재하는 회로에서 보존용 공간을 최소화한다; (3) 추가로, 플립플롭에 이미 할당된 보존용 공간 중 일부를 제거할 수 있는 조건을 찾고, 이를 이용해 보존용 공간을 더 감소시킨다. 벤치마크 회로의 실험 결과는 본 논문에서 제안한 방법론이 기존의 보존용 공간 할당 방법론보다 더 적은 보존용 공간을 할당하며, 따라서 칩의 면적 및 전력 소모를 감소시킬 수 있음을 보인다.Low power operation of a chip is an important issue, and its importance is increasing as the process technology advances. This dissertation addresses the methodology of operating at low power for each of the SRAM and logic constituting the chip. Firstly, we propose a methodology to infer the minimum operating voltage at which SRAM failure does not occur in all SRAM blocks in the chip operating on near threshold voltage (NTV) regime through the measurement of a monitoring circuit. Operating the chip on NTV regime is one of the most effective ways to increase energy efficiency, but in case of SRAM, it is difficult to lower the operating voltage because of SRAM failure. However, since the process variation on each chip is different, the minimum operating voltage is also different for each chip. If it is possible to infer the minimum operating voltage of SRAM blocks of each chip through monitoring, energy efficiency can be increased by applying different voltage. In this dissertation, we propose a new methodology of resolving this problem. Specifically, (1) we propose to infer minimum operation voltage of SRAM in design infra development phase, and assign the voltage using measurement of SRAM monitor in silicon production phase; (2) we define a SRAM monitor and features to be monitored that can monitor process variation on SRAM blocks including SRAM bitcell and peripheral circuits; (3) we propose a new methodology of inferring minimum operating voltage of SRAM blocks in a chip that does not cause read, write, and access failures under a target confidence level. Through experiments with benchmark circuits, it is confirmed that applying different voltage to SRAM blocks in each chip that inferred by our proposed methodology can save overall power consumption of SRAM bitcell array compared to applying same voltage to SRAM blocks in all chips, while meeting the same yield target. Secondly, we propose a methodology to resolve the problem of the conventional retention storage allocation methods and thereby further reduce leakage power consumption of power gated circuit. Conventional retention storage allocation methods have problem of not fully utilizing the advantage of multi-bit retention storage because of the unavoidable allocation of retention storage on flip-flops with mux-feedback loop. In this dissertation, we propose a new methodology of breaking the bottleneck of minimizing the state retention storage. Specifically, (1) we find a condition that mux-feedback loop can be disregarded during the retention storage allocation; (2) utilizing the condition, we minimize the retention storage of circuits that contain many flip-flops with mux-feedback loop; (3) we find a condition to remove some of the retention storage already allocated to each of flip-flops and propose to further reduce the retention storage. Through experiments with benchmark circuits, it is confirmed that our proposed methodology allocates less retention storage compared to the state-of-the-art methods, occupying less cell area and consuming less power.1 Introduction 1 1.1 Low Voltage SRAM Monitoring Methodology 1 1.2 Retention Storage Allocation on Power Gated Circuit 5 1.3 Contributions of this Dissertation 8 2 SRAM On-Chip Monitoring Methodology for High Yield and Energy Efficient Memory Operation at Near Threshold Voltage 13 2.1 SRAM Failures 13 2.1.1 Read Failure 13 2.1.2 Write Failure 15 2.1.3 Access Failure 16 2.1.4 Hold Failure 16 2.2 SRAM On-chip Monitoring Methodology: Bitcell Variation 18 2.2.1 Overall Flow 18 2.2.2 SRAM Monitor and Monitoring Target 18 2.2.3 Vfail to Vddmin Inference 22 2.3 SRAM On-chip Monitoring Methodology: Peripheral Circuit IR Drop and Variation 29 2.3.1 Consideration of IR Drop 29 2.3.2 Consideration of Peripheral Circuit Variation 30 2.3.3 Vddmin Prediction including Access Failure Prohibition 33 2.4 Experimental Results 41 2.4.1 Vddmin Considering Read and Write Failures 42 2.4.2 Vddmin Considering Read/Write and Access Failures 45 2.4.3 Observation for Practical Use 45 3 Allocation of Always-On State Retention Storage for Power Gated Circuits - Steady State Driven Approach 49 3.1 Motivations and Analysis 49 3.1.1 Impact of Self-loop on Power Gating 49 3.1.2 Circuit Behavior Before Sleeping 52 3.1.3 Wakeup Latency vs. Retention Storage 54 3.2 Steady State Driven Retention Storage Allocation 56 3.2.1 Extracting Steady State Self-loop FFs 57 3.2.2 Allocating State Retention Storage 59 3.2.3 Designing and Optimizing Steady State Monitoring Logic 59 3.2.4 Analysis of the Impact of Steady State Monitoring Time on the Standby Power 63 3.3 Retention Storage Refinement Utilizing Steadiness 65 3.3.1 Extracting Flip-flops for Retention Storage Refinement 66 3.3.2 Designing State Monitoring Logic and Control Signals 68 3.4 Experimental Results 73 3.4.1 Comparison of State Retention Storage 75 3.4.2 Comparison of Power Consumption 79 3.4.3 Impact on Circuit Performance 82 3.4.4 Support for Immediate Power Gating 83 4 Conclusions 89 4.1 Chapter 2 89 4.2 Chapter 3 90박

Static analysis of energy consumption for LLVM IR programs

Energy models can be constructed by characterizing the energy consumed by executing each instruction in a processor's instruction set. This can be used to determine how much energy is required to execute a sequence of assembly instructions, without the need to instrument or measure hardware. However, statically analyzing low-level program structures is hard, and the gap between the high-level program structure and the low-level energy models needs to be bridged. We have developed techniques for performing a static analysis on the intermediate compiler representations of a program. Specifically, we target LLVM IR, a representation used by modern compilers, including Clang. Using these techniques we can automatically infer an estimate of the energy consumed when running a function under different platforms, using different compilers. One of the challenges in doing so is that of determining an energy cost of executing LLVM IR program segments, for which we have developed two different approaches. When this information is used in conjunction with our analysis, we are able to infer energy formulae that characterize the energy consumption for a particular program. This approach can be applied to any languages targeting the LLVM toolchain, including C and XC or architectures such as ARM Cortex-M or XMOS xCORE, with a focus towards embedded platforms. Our techniques are validated on these platforms by comparing the static analysis results to the physical measurements taken from the hardware. Static energy consumption estimation enables energy-aware software development, without requiring hardware knowledge

Phase Locked Loop Test Methodology

Phase locked loops are incorporated into almost every large-scale mixed signal and digital system on chip (SOC). Various types of PLL architectures exist including fully analogue, fully digital, semi-digital, and software based. Currently the most commonly used PLL architecture for SOC environments and chipset applications is the Charge-Pump (CP) semi-digital type. This architecture is commonly used for clock synthesis applications, such as the supply of a high frequency on-chip clock, which is derived from a low frequency board level clock. In addition, CP-PLL architectures are now frequently used for demanding RF (Radio Frequency) synthesis, and data synchronization applications. On chip system blocks that rely on correct PLL operation may include third party IP cores, ADCs, DACs and user defined logic (UDL). Basically, any on-chip function that requires a stable clock will be reliant on correct PLL operation. As a direct consequence it is essential that the PLL function is reliably verified during both the design and debug phase and through production testing. This chapter focuses on test approaches related to embedded CP-PLLs used for the purpose of clock generation for SOC. However, methods discussed will generally apply to CP-PLLs used for other applications

EFFICIENT HARDWARE PRIMITIVES FOR SECURING LIGHTWEIGHT SYSTEMS

In the era of IoT and ubiquitous computing, the collection and communication of sensitive data is increasingly being handled by lightweight Integrated Circuits. Efficient hardware implementations of crytographic primitives for resource constrained applications have become critical, especially block ciphers which perform fundamental operations such as encryption, decryption, and even hashing. We study the efficiency of block ciphers under different implementation styles. For low latency applications that use unrolled block cipher implementations, we design a glitch filter to reduce energy consumption. For lightweight applications, we design a novel architecture for the widely used AES cipher. The design eliminates inefficiencies in data movement and clock activity, thereby significantly improving energy efficiency over state-of-the-art architectures. Apart from efficiency, vulnerability to implementation attacks are a concern, which we mitigate by our randomization capable lightweight AES architecture. We fabricate our designs in a commercial 16nm FinFET technology and present measured testchip data on energy consumption and side channel resistance. Finally, we address the problem of supply chain security by using image processing techniques to extract fingerprints from surface texture of plastic IC packages for IC authentication and counterfeit prevention. Collectively these works present efficient and cost effective solutions to secure lightweight systems

Techniques for Improving Security and Trustworthiness of Integrated Circuits

The integrated circuit (IC) development process is becoming increasingly vulnerable to malicious activities because untrusted parties could be involved in this IC development flow. There are four typical problems that impact the security and trustworthiness of ICs used in military, financial, transportation, or other critical systems: (i) Malicious inclusions and alterations, known as hardware Trojans, can be inserted into a design by modifying the design during GDSII development and fabrication. Hardware Trojans in ICs may cause malfunctions, lower the reliability of ICs, leak confidential information to adversaries or even destroy the system under specifically designed conditions. (ii) The number of circuit-related counterfeiting incidents reported by component manufacturers has increased significantly over the past few years with recycled ICs contributing the largest percentage of the total reported counterfeiting incidents. Since these recycled ICs have been used in the field before, the performance and reliability of such ICs has been degraded by aging effects and harsh recycling process. (iii) Reverse engineering (RE) is process of extracting a circuit’s gate-level netlist, and/or inferring its functionality. The RE causes threats to the design because attackers can steal and pirate a design (IP piracy), identify the device technology, or facilitate other hardware attacks. (iv) Traditional tools for uniquely identifying devices are vulnerable to non-invasive or invasive physical attacks. Securing the ID/key is of utmost importance since leakage of even a single device ID/key could be exploited by an adversary to hack other devices or produce pirated devices. In this work, we have developed a series of design and test methodologies to deal with these four challenging issues and thus enhance the security, trustworthiness and reliability of ICs. The techniques proposed in this thesis include: a path delay fingerprinting technique for detection of hardware Trojans, recycled ICs, and other types counterfeit ICs including remarked, overproduced, and cloned ICs with their unique identifiers; a Built-In Self-Authentication (BISA) technique to prevent hardware Trojan insertions by untrusted fabrication facilities; an efficient and secure split manufacturing via Obfuscated Built-In Self-Authentication (OBISA) technique to prevent reverse engineering by untrusted fabrication facilities; and a novel bit selection approach for obtaining the most reliable bits for SRAM-based physical unclonable function (PUF) across environmental conditions and silicon aging effects

Mobiililaitteiden hienojakoinen energiaprofilointi

Mobile phones have several use cases such as making a phone call, sending an SMS, browsing the Internet, or playing a game. Mobile phones are also equipped with a wide variety of hardware allowing these activities. The overall energy consumption is easily measurable but it does not explain how much power is dissipated on particular activities and which devices are mostly responsible for the consumption. Thus, this thesis defines the concept of fine-grained energy profiling where the total energy consumed is broken down into subsystems. This thesis examines mobile phone power dissipation and energy consumption analysis. It describes how to measure overall total energy consumed by the device and develops methods that allow breaking down the energy consumption to components or subsystems. Specifically, the tools developed in this thesis allow studying the energy consumed by the CPU, GPU, display, WiFi, Cellular 3G and SSD disk. The device studied here is the Nokia N900 Maemo/Linux phone. This thesis describes a full-system power measurement setup including a fake battery and DAQ acting as an electric power meter. The thesis also develops logging tools that monitor the subsystem load and provide a method for formulating a linear regression model between these two through a set of microbenchmarks. This model allows estimating the subsystem energy consumption and total energy consumption based on observed loads of the subsystems. The model achieved 80% accuracy when compared with measured total energy consumption to the total power dissipation predicted by model.Matkapuhelimia voi käyttää moniin tarkoituksiin kuten puheluihin, tekstiviestien lähettämiseen, Internet-selailuun tai pelien pelaamiseen. Tämän mahdollistamiseksi nykyaikaisissa matkapuhelimissa on paljon erilaisia laitteistokomponentteja eli alijärjestelmiä. Matkapuhelimen kokonaisvirrankulutus on helppo mitata, mutta se ei selitä sitä, kuinka paljon kukin alijärjestelmä kuluttaa energiaa. Tämän ongelman ratkaisemiseksi tässä työssä määritellään hienojakoisen energiaprofiloinnin käsite, jonka avulla kokonaisenergiankulutus voidaan jakaa alijärjestelmien energiankulutukseksi. Tässä työssä tutkitaan matkapuhelimen tehon ja energiankulutuksen analysointia. Työssä kehitetään menetelmä matkapuhelimen kokonaisenergiankulutuksen mittaamiseen. Lisäksi esitellään menetelmä, jonka avulla energiankulutus jyvitetään matkapuhelimen alijärjestelmille. Työssä jyvitys tehdään seuraaville alijärjestelmille: suoritin (CPU), grafiikkasuoritin (GPU), näyttö, langaton verkko (WiFi), mobiilidatayhteys (3G) sekä tallennuslevy (SSD). Laitteena käytettiin Nokia N900 Maemo/Linux -puhelinta. Työssä esitellään kokonaisenergiankulutuksen mittausjärjestely, joka sisältää valeakun ja virrankulutusmittarina toimivan DAQ-laitteen. Lisäksi työssä kehitetään työkalu, jonka avulla matkapuhelimen alijärjestelmien käyttöastetta voidaan tarkkailla ja tallentaa. Lopuksi työssä esitellään lineaariseen regressioon perustuva mallinnus, joka mahdollistaa mitatun tehon ja kokonaisenergiankulutuksen jyvittämisen yksittäisille alijärjestelmäkomponenteille. Työssä kehitetty malli saavutti noin 80 % selitysasteen, kun mallin ennustamaa tehonkulutusta verrattiin mitattuun tehonkulutukseen