Ground Profile Recovery from Aerial 3D LiDAR-based Maps

The paper presents the study and implementation of the ground detection methodology with filtration and removal of forest points from LiDAR-based 3D point cloud using the Cloth Simulation Filtering (CSF) algorithm. The methodology allows to recover a terrestrial relief and create a landscape map of a forestry region. As the proof-of-concept, we provided the outdoor flight experiment, launching a hexacopter under a mixed forestry region with sharp ground changes nearby Innopolis city (Russia), which demonstrated the encouraging results for both ground detection and methodology robustness.Comment: 8 pages, FRUCT-2019 conferenc

An automated approach for extracting forest inventory data from individual trees using a handheld mobile laser scanner

Many dendrometric parameters have been estimated by light detection and ranging (LiDAR) technology over the last two decades. Handheld mobile laser scanning (HMLS), in particular, has come into prominence as a cost-effective data collection method for forest inventories. However, most pilot studies were performed in domesticated landscapes, where the environmental settings were far from those presented by (near )natural forest ecosystems. Besides, these studies consisted of numerous data processing steps, which were challenging when employed by manual means. Here we present an automated approach for deriving key inventory data using the HMLS method in natural forest areas. To this end, many algorithms (e.g., cylinder/circle/ellipse fitting) and machine learning models (e.g., random forest classifier) were used in the data processing stage for estimation of the tree diameter at breast height (DBH) and the number of trees. The estimates were then compared against the reference data obtained by field measurements from six forest sample plots. The results showed that correlations between the estimated and reference DBHs were very strong at the plot level (r=0.83-0.99, p> hard plotso << located at rocky terrains with dense undergrowth and irregular trunks. We concluded that area-based forest inventories might hugely benefit from the HMLS method, particularly in "easy plots". By improving the algorithmic performances, the accuracy levels can be further increased by future research

Predicting growing stock volume of Eucalyptus plantations using 3-D point clouds derived from UAV imagery and ALS data

Estimating forest inventory variables is important in monitoring forest resources and mitigating climate change. In this respect, forest managers require flexible, non-destructive methods for estimating volume and biomass. High-resolution and low-cost remote sensing data are increasingly available to measure three-dimensional (3D) canopy structure and to model forest structural attributes. The main objective of this study was to evaluate and compare the individual tree volume estimates derived from high-density point clouds obtained from airborne laser scanning (ALS) and digital aerial photogrammetry (DAP) in Eucalyptus spp. plantations. Object-based image analysis (OBIA) techniques were applied for individual tree crown (ITC) delineation. The ITC algorithm applied correctly detected and delineated 199 trees from ALS-derived data, while 192 trees were correctly identified using DAP-based point clouds acquired fromUnmannedAerialVehicles(UAV), representing accuracy levels of respectively 62% and 60%. Addressing volume modelling, non-linear regression fit based on individual tree height and individual crown area derived from the ITC provided the following results: Model E ciency (Mef) = 0.43 and 0.46, Root Mean Square Error (RMSE) = 0.030 m3 and 0.026 m3, rRMSE = 20.31% and 19.97%, and an approximately unbiased results (0.025 m3 and 0.0004 m3) using DAP and ALS-based estimations, respectively. No significant di erence was found between the observed value (field data) and volume estimation from ALS and DAP (p-value from t-test statistic = 0.99 and 0.98, respectively). The proposed approaches could also be used to estimate basal area or biomass stocks in Eucalyptus spp. plantationsinfo:eu-repo/semantics/publishedVersio

Single-tree detection in high-density LiDAR data from UAV-based survey

UAV-based LiDAR survey provides very-high-density point clouds, which involve very rich information about forest detailed structure, allowing for detection of individual trees, as well as demanding high computational load. Single-tree detection is of great interest for forest management and ecology purposes, and the task is relatively well solved for forests made of single or largely dominant species, and trees having a very evident pointed shape in the upper part of the canopy (in particular conifers). Most authors proposed methods based totally or partially on search of local maxima in the canopy, which has poor performance for species that have flat or irregular upper canopy, and for mixed forests, especially where taller trees hide smaller ones. Such considerations apply in particular to Mediterranean hardwood forests. In such context, it is imperative to use the whole volume of the point cloud, however keeping computational load tractable. The authors propose the use of a methodology based on modelling the 3D-shape of the tree, which improves performance w.r.t to maxima-based models. A case study, performed on a hazel grove, is provided to document performance improvement on a relatively simple, but significant, case

Developing Allometric Equations for Teak Plantations Located in the Coastal Region of Ecuador from Terrestrial Laser Scanning Data

Traditional studies aimed at developing allometric models to estimate dry above-ground biomass (AGB) and other tree-level variables, such as tree stem commercial volume (TSCV) or tree stem volume (TSV), usually involves cutting down the trees. Although this method has low uncertainty, it is quite costly and inefficient since it requires a very time-consuming field work. In order to assist in data collection and processing, remote sensing is allowing the application of non-destructive sampling methods such as that based on terrestrial laser scanning (TLS). In this work, TLS-derived point clouds were used to digitally reconstruct the tree stem of a set of teak trees (Tectona grandis Linn. F.) from 58 circular reference plots of 18 m radius belonging to three different plantations located in the Coastal Region of Ecuador. After manually selecting the appropriate trees from the entire sample, semi-automatic data processing was performed to provide measurements of TSCV and TSV, together with estimates of AGB values at tree level. These observed values were used to develop allometric models, based on diameter at breast height (DBH), total tree height (h), or the metric DBH2 × h, by applying a robust regression method to remove likely outliers. Results showed that the developed allometric models performed reasonably well, especially those based on the metric DBH2 × h, providing low bias estimates and relative RMSE values of 21.60% and 16.41% for TSCV and TSV, respectively. Allometric models only based on tree height were derived from replacing DBH by h in the expression DBH2 x h, according to adjusted expressions depending on DBH classes (ranges of DBH). This finding can facilitate the obtaining of variables such as AGB (carbon stock) and commercial volume of wood over teak plantations in the Coastal Region of Ecuador from only knowing the tree height, constituting a promising method to address large-scale teak plantations monitoring from the canopy height models derived from digital aerial stereophotogrammetry

To What Extent Can UAV Photogrammetry Replicate UAV LiDAR to Determine Forest Structure? A Test in Two Contrasting Tropical Forests

Tropical forests are complex multi-layered systems, with the height and three-dimensional (3D) structure of trees influencing the carbon and biodiversity they contain. Fine-resolution 3D data on forest structure can be collected reliably with Light Detection and Ranging (LiDAR) sensors mounted on aircraft or Unoccupied Aerial Vehicles (UAVs), however, they remain expensive to collect and process. Structure-from-Motion (SfM) Digital Aerial Photogrammetry (SfM-DAP), which relies on photographs taken of the same area from multiple angles, is a lower-cost alternative to LiDAR for generating 3D data on forest structure. Here, we evaluate how SfM-DAP compares to LiDAR data acquired concurrently using a fixed-wing UAV, over two contrasting tropical forests in Gabon and Peru. We show that SfM-DAP data cannot be used in isolation to measure key aspects of forest structure, including canopy height (%Bias: 40%–50%), fractional cover, and gap fraction, due to difficulties measuring ground elevation, even under low tree cover. However, we find even in complex forests, SfM-DAP is an effective means of measuring top-of-canopy structure, including surface heterogeneity, and is capable of producing similar measurements of vertical structure as LiDAR. Thus, in areas where ground height is known, SfM-DAP is an effective method for measuring important aspects of forest structure, including canopy height, and gaps, however, without ground data, SfM-DAP is of more limited utility. Our results support the growing evidence base pointing to photogrammetry as a viable complement, or alternative, to LiDAR, capable of providing much needed information to support the mapping and monitoring of biomass and biodiversity

A Pipeline of 3D Scene Reconstruction from Point Clouds

3D technologies are becoming increasingly popular as their applications in industrial, consumer, entertainment, healthcare, education, and governmental increase in number. According to market predictions, the total 3D modeling and mapping market is expected to grow from $1.1 billion in 2013 to$7.7 billion by 2018. Thus, 3D modeling techniques for different data sources are urgently needed. This thesis addresses techniques for automated point cloud classification and the reconstruction of 3D scenes (including terrain models, 3D buildings and 3D road networks). First, georeferenced binary image processing techniques were developed for various point cloud classifications. Second, robust methods for the pipeline from the original point cloud to 3D model construction were proposed. Third, the reconstruction for the levels of detail (LoDs) of 1-3 (CityGML website) of 3D models was demonstrated. Fourth, different data sources for 3D model reconstruction were studied. The strengths and weaknesses of using the different data sources were addressed. Mobile laser scanning (MLS), unmanned aerial vehicle (UAV) images, airborne laser scanning (ALS), and the Finnish National Land Survey’s open geospatial data sources e.g. a topographic database, were employed as test data. Among these data sources, MLS data from three different systems were explored, and three different densities of ALS point clouds (0.8, 8 and 50 points/m2) were studied. The results were compared with reference data such as an orthophoto with a ground sample distance of 20cm or measured reference points from existing software to evaluate their quality. The results showed that 74.6% of building roofs were reconstructed with the automated process. The resulting building models provided an average height deviation of 15 cm. A total of 6% of model points had a greater than one-pixel deviation from laser points. A total of 2.5% had a deviation of greater than two pixels. The pixel size was determined by the average distance of input laser points. The 3D roads were reconstructed with an average width deviation of 22 cm and an average height deviation of 14 cm. The results demonstrated that 93.4% of building roofs were correctly classified from sparse ALS and that 93.3% of power line points are detected from the six sets of dense ALS data located in forested areas. This study demonstrates the operability of 3D model construction for LoDs of 1-3 via the proposed methodologies and datasets. The study is beneficial to future applications, such as 3D-model-based navigation applications, the updating of 2D topographic databases into 3D maps and rapid, large-area 3D scene reconstruction. 3D-teknologiat ovat tulleet yhä suositummiksi niiden sovellusalojen lisääntyessä teollisuudessa, kuluttajatuotteissa, terveydenhuollossa, koulutuksessa ja hallinnossa. Ennusteiden mukaan 3D-mallinnus- ja -kartoitusmarkkinat kasvavat vuoden 2013 1,1 miljardista dollarista 7,7 miljardiin vuoteen 2018 mennessä. Erilaisia aineistoja käyttäviä 3D-mallinnustekniikoita tarvitaankin yhä enemmän. Tässä väitöskirjatutkimuksessa kehitettiin automaattisen pistepilviaineiston luokittelutekniikoita ja rekonstruoitiin 3D-ympäristöja (maanpintamalleja, rakennuksia ja tieverkkoja). Georeferoitujen binääristen kuvien prosessointitekniikoita kehitettiin useiden pilvipisteaineistojen luokitteluun. Työssä esitetään robusteja menetelmiä alkuperäisestä pistepilvestä 3D-malliin eri CityGML-standardin tarkkuustasoilla. Myös eri aineistolähteitä 3D-mallien rekonstruointiin tutkittiin. Eri aineistolähteiden käytön heikkoudet ja vahvuudet analysoitiin. Testiaineistona käytettiin liikkuvalla keilauksella (mobile laser scanning, MLS) ja ilmakeilauksella (airborne laser scanning, ALS) saatua laserkeilausaineistoja, miehittämättömillä lennokeilla (unmanned aerial vehicle, UAV) otettuja kuvia sekä Maanmittauslaitoksen avoimia aineistoja, kuten maastotietokantaa. Liikkuvalla laserkeilauksella kerätyn aineiston osalta tutkimuksessa käytettiin kolmella eri järjestelmällä saatua dataa, ja kolmen eri tarkkuustason (0,8, 8 ja 50 pistettä/m2) ilmalaserkeilausaineistoa. Tutkimuksessa saatuja tulosten laatua arvioitiin vertaamalla niitä referenssiaineistoon, jona käytettiin ortokuvia (GSD 20cm) ja nykyisissä ohjelmistoissa olevia mitattuja referenssipisteitä. 74,6 % rakennusten katoista saatiin rekonstruoitua automaattisella prosessilla. Rakennusmallien korkeuksien keskipoikkeama oli 15 cm. 6 %:lla mallin pisteistä oli yli yhden pikselin poikkeama laseraineiston pisteisiin verrattuna. 2,5 %:lla oli yli kahden pikselin poikkeama. Pikselikoko määriteltiin kahden laserpisteen välimatkan keskiarvona. Rekonstruoitujen teiden leveyden keskipoikkeama oli 22 cm ja korkeuden keskipoikkeama oli 14 cm. Tulokset osoittavat että 93,4 % rakennuksista saatiin luokiteltua oikein harvasta ilmalaserkeilausaineistosta ja 93,3 % sähköjohdoista saatiin havaittua kuudesta tiheästä metsäalueen ilmalaserkeilausaineistosta. Tutkimus demonstroi 3D-mallin konstruktion toimivuutta tarkkuustasoilla (LoD) 1-3 esitetyillä menetelmillä ja aineistoilla. Tulokset ovat hyödyllisiä kehitettäessä tulevaisuuden sovelluksia, kuten 3D-malleihin perustuvia navigointisovelluksia, topografisten 2D-karttojen ajantasaistamista 3D-kartoiksi, ja nopeaa suurten alueiden 3D-ympäristöjen rekonstruktiota