Dynamics and control of flexible manipulators

Flexible link manipulators (FLM) are well-known for their light mass and small energy consumption compared to rigid link manipulators (RLM). These advantages of FLM are even of greater importance in applications where energy efficiency is crucial, such as in space applications. However, RLM are still preferred over FLM for industrial applications. This is due to the fact that the reliability and predictability of the performance of FLM are not yet as good as those of RLM. The major cause for these drawbacks is link flexibility, which not only makes the dynamic modeling of FLM very challenging, but also turns its end-effector trajectory tracking (EETT) into a complicated control problem. The major objectives of the research undertaken in this project were to develop a dynamic model for a FLM and model-based controllers for the EETT. Therefore, the dynamic model of FLM was first derived. This dynamic model was then used to develop the EETT controllers. A dynamic model of a FLM was derived by means of a novel method using the dynamic model of a single flexible link manipulator on a moving base (SFLMB). The computational efficiency of this method is among its novelties. To obtain the dynamic model, the Lagrange method was adopted. Derivation of the kinetic energy and the calculation of the corresponding derivatives, which are required in the Lagrange method, are complex for the FLM. The new method introduced in this thesis alleviated these complexities by calculating the kinetic energy and the required derivatives only for a SFLMB, which were much simpler than those of the FLM. To verify the derived dynamic model the simulation results for a two-link manipulator, with both links being flexible, were compared with those of full nonlinear finite element analysis. These comparisons showed sound agreement. A new controller for EETT of FLM, which used the singularly perturbed form of the dynamic model and the integral manifold concept, was developed. By using the integral manifold concept the links’ lateral deflections were approximately represented in terms of the rotations of the links and input torques. Therefore the end-effector displacement, which was composed of the rotations of the links and links’ lateral deflections, was expressed in terms of the rotations of the links and input torques. The input torques were then selected to reduce the EETT error. The originalities of this controller, which was based on the singularly perturbed form of the dynamic model of FLM, are: (1) it is easy and computationally efficient to implement, and (2) it does not require the time derivative of links’ lateral deflections, which are impractical to measure. The ease and computational efficiency of the new controller were due to the use of the several properties of the dynamic model of the FLM. This controller was first employed for the EETT of a single flexible link manipulator (SFLM) with a linear model. The novel controller was then extended for the EETT of a class of flexible link manipulators, which were composed of a chain of rigid links with only a flexible end-link (CRFE). Finally it was used for the EETT of a FLM with all links being flexible. The simulation results showed the effectiveness of the new controller. These simulations were conducted on a SFLM, a CRFE (with the first link being rigid and second link being flexible) and finally a two-link manipulator, with both links being flexible. Moreover, the feasibility of the new controller proposed in this thesis was verified by experimental studies carried out using the equipment available in the newly established Robotic Laboratory at the University of Saskatchewan. The experimental verifications were performed on a SFLM and a two-link manipulator, with first link being rigid and second link being flexible.Another new controller was also introduced in this thesis for the EETT of single flexible link manipulators with the linear dynamic model. This controller combined the feedforward torque, which was required to move the end-effector along the desired path, with a feedback controller. The novelty of this EETT controller was in developing a new method for the derivation of the feedforward torque. The feedforward torque was obtained by redefining the desired end-effector trajectory. For the end-effector trajectory redefinition, the summation of the stable exponential functions was used. Simulation studies showed the effectiveness of this new controller. Its feasibility was also proven by experimental verification carried out in the Robotic Laboratory at the University of Saskatchewan

MUSME 2011 4 th International Symposium on Multibody Systems and Mechatronics

El libro de actas recoge las aportaciones de los autores a través de los correspondientes artículos a la Dinámica de Sistemas Multicuerpo y la Mecatrónica (Musme). Estas disciplinas se han convertido en una importante herramienta para diseñar máquinas, analizar prototipos virtuales y realizar análisis CAD sobre complejos sistemas mecánicos articulados multicuerpo. La dinámica de sistemas multicuerpo comprende un gran número de aspectos que incluyen la mecánica, dinámica estructural, matemáticas aplicadas, métodos de control, ciencia de los ordenadores y mecatrónica. Los artículos recogidos en el libro de actas están relacionados con alguno de los siguientes tópicos del congreso: Análisis y síntesis de mecanismos ; Diseño de algoritmos para sistemas mecatrónicos ; Procedimientos de simulación y resultados ; Prototipos y rendimiento ; Robots y micromáquinas ; Validaciones experimentales ; Teoría de simulación mecatrónica ; Sistemas mecatrónicos ; Control de sistemas mecatrónicosUniversitat Politècnica de València (2011). MUSME 2011 4 th International Symposium on Multibody Systems and Mechatronics. Editorial Universitat Politècnica de València. http://hdl.handle.net/10251/13224Archivo delegad

Trajectory Tracking Control of Parallel Manipulator with Integral Manifold and Observer

In view of the problem that notable flexible displacement will occur for parallel manipulators when operating at high speed, the composite controller based on the integral manifold and high-gain observer is proposed for trajectory tracking and the 3RRR parallel manipulator is taken as the object. Based on the stiffness matrix, the small variable is introduced to decompose the rigid-flexible coupling dynamic model into slow and fast subsystem. For the slow subsystem, the backstepping control is applied for rigid motion tracking. In order to account for the links’ flexible displacement the corrective torque is deduced, and the compensation for the flexible displacement is realized. For the fast subsystem, the sliding mode control is utilized to suppress the vibration. The high-gain observer is designed to avoid the measurement of the curvature rate of flexible links. Also, the stability of the overall system is proven with the Lyapunov stability theorem and the upper bound of the small variable is obtained. At last, the proposed composite controller together with the singular perturbation control and the rigid body model-based backstepping control are simulated, and vibration suppression and tracking performances are compared to validate the proposed control scheme

Advances in Mechanical Systems Dynamics 2020

The fundamentals of mechanical system dynamics were established before the beginning of the industrial era. The 18th century was a very important time for science and was characterized by the development of classical mechanics. This development progressed in the 19th century, and new, important applications related to industrialization were found and studied. The development of computers in the 20th century revolutionized mechanical system dynamics owing to the development of numerical simulation. We are now in the presence of the fourth industrial revolution. Mechanical systems are increasingly integrated with electrical, fluidic, and electronic systems, and the industrial environment has become characterized by the cyber-physical systems of industry 4.0. Within this framework, the status-of-the-art has become represented by integrated mechanical systems and supported by accurate dynamic models able to predict their dynamic behavior. Therefore, mechanical systems dynamics will play a central role in forthcoming years. This Special Issue aims to disseminate the latest research findings and ideas in the field of mechanical systems dynamics, with particular emphasis on novel trends and applications

Proceedings of the ECCOMAS Thematic Conference on Multibody Dynamics 2015

This volume contains the full papers accepted for presentation at the ECCOMAS Thematic Conference on Multibody Dynamics 2015 held in the Barcelona School of Industrial Engineering, Universitat Politècnica de Catalunya, on June 29 - July 2, 2015. The ECCOMAS Thematic Conference on Multibody Dynamics is an international meeting held once every two years in a European country. Continuing the very successful series of past conferences that have been organized in Lisbon (2003), Madrid (2005), Milan (2007), Warsaw (2009), Brussels (2011) and Zagreb (2013); this edition will once again serve as a meeting point for the international researchers, scientists and experts from academia, research laboratories and industry working in the area of multibody dynamics. Applications are related to many fields of contemporary engineering, such as vehicle and railway systems, aeronautical and space vehicles, robotic manipulators, mechatronic and autonomous systems, smart structures, biomechanical systems and nanotechnologies. The topics of the conference include, but are not restricted to: ● Formulations and Numerical Methods ● Efficient Methods and Real-Time Applications ● Flexible Multibody Dynamics ● Contact Dynamics and Constraints ● Multiphysics and Coupled Problems ● Control and Optimization ● Software Development and Computer Technology ● Aerospace and Maritime Applications ● Biomechanics ● Railroad Vehicle Dynamics ● Road Vehicle Dynamics ● Robotics ● Benchmark ProblemsPostprint (published version