Quantization noise analysis of a closed-loop PWM controller that includes Σ-Δ modulation

Σ-Δ modulation is a popular noise shaping technique which is used to move the quantization noise out of the frequency band of interest. Recently, a number of authors have applied this technique to a pulse width modulation (PWM) controller for switching power converters. However, previous analysis has not incorporated the effects of analog-to-digital converter (ADC) resolution or feedback control on the Σ-Δ modulator. In this work, quantization due to ADC resolution and PWM resolution are analyzed, considering the effects of noise-shaping and feedback. A number of simulations have been performed to explore the impact of various design choices on output noise. The study variables included the order of the Σ-Δ modulator, resolution of ADC, resolution of DPWM, the plant and the compensator. The theoretical model developed is used to generate the expected system Power Spectral Density (PSD) curves for each design choice and simulations techniques are used to validate the analysis. Experimental analysis has been performed on a digital voltage-mode control (VMC) synchronous buck converter and the output voltage PSD curves are generated using the welch method and compared with the theoretical and the simulation results. The experimental PSD curves for the 1st-order modulator match the simulation and theoretical PSD curves. This suggests that the theoretical model is a useful approximation and similar methods can be used to analyze the contribution of the quantizers to the output noise of a closed-loop controller system --Abstract, page iii

Cascaded Linear Regulator with Negative Voltage Tracking Switching Regulator

DC-DC converters can be separated into two main groups: switching converters and linear regulators. Linear regulators such as Low Dropout Regulators (LDOs) are straightforward to implement and have a very stable output with low voltage ripple. However, the efficiency of an LDO can fluctuate greatly, as the power dissipation is a function of the device’s input and output. On the other hand, a switching regulator uses a switch to regulate energy levels. These types of regulators are more versatile when a larger change of voltage is needed, as efficiency is relatively stable across larger steps of voltages. However, switching regulators tend to have a larger output voltage ripple, which can be an issue for sensitive systems. An approach to utilize both in cascaded configuration while providing a negative output voltage will be presented in this paper. The proposed two-stage conversion system consists of a switching pre-regulator that can track the negative output voltage of the second stage (LDO) such that the difference between input and output voltages is always kept small under varying output voltage while maintaining the high overall conversion efficiency. Computer simulation and hardware results demonstrate that the proposed system can track the negative output voltage well. Additionally, the results show that the proposed system can provide and maintain good overall efficiency, load regulation, and output voltage ripple across a wide range of outputs

A three-switch high-voltage converter

A novel single active switch two-diodes high-voltage converter is presented. This converter can operate into a capacitor-diode voltage multiplier, which offers simpler structure and control, higher efficiency, reduced electromagnetic interference (EMI), and size and weight savings compared with traditional switched-mode regulated voltage multipliers. Two significant advantages are the continuous input current and easy isolation extension. The new converter is experimentally verified. Both the steady-state and dynamic theoretical models are correlated well with the experimental dat

Supercapacitor assisted LDO (SCALDO) techniquean extra low frequency design approach to high efficiency DC-DC converters and how it compares with the classical switched capacitor converters

Supercapacitor assisted low dropout regulators (SCALDO) were proposed as an alternative design approach to DC-DC converters, where the supercapacitor circulation frequency (switching frequency) is in the order of few Hz to few 10s of Hz, with an output stage based on a low dropout regulator stage. For converters such as 12–5V, 5–3.3V and 5–1.5V, the technique provides efficiency improvement factors of 2, 1.33 and 3 respectively, in compared to linear converters with same input-output combinations. In a 5–1.5V SCALDO regulator, using thin profile supercapacitors in the range of fractional farads to few farads, this translates to an approximate end to end efficiency of near 90%. However, there were concerns that this patented technique is merely a variation of well-known switched capacitor (charge pump) converters. This paper is aimed at providing a broad overview of the capability of SCALDO technique with generalized theory, indicating its capabilities and limitations, and comparing the practical performance with a typical switched capacitor converter of similar current capability

Low Voltage Regulator Modules and Single Stage Front-end Converters

Evolution in microprocessor technology poses new challenges for supplying power to these devices. To meet demands for faster and more efficient data processing, modem microprocessors are being designed with lower voltage implementations. More devices will be packed on a single processor chip and the processors will operate at higher frequencies, exceeding 1GHz. New high-performance microprocessors may require from 40 to 80 watts of power for the CPU alone. Load current must be supplied with up to 30A/µs slew rate while keeping the output voltage within tight regulation and response time tolerances. Therefore, special power supplies and Voltage Regulator Modules (VRMs) are needed to provide lower voltage with higher current and fast response. In the part one (chapter 2,3,4) of this dissertation, several low-voltage high-current VRM technologies are proposed for future generation microprocessors and ICs. The developed VRMs with these new technologies have advantages over conventional ones in terms of efficiency, transient response and cost. In most cases, the VRMs draw currents from DC bus for which front-end converters are used as a DC source. As the use of AC/DC frond-end converters continues to increase, more distorted mains current is drawn from the line, resulting in lower power factor and high total harmonic distortion. As a branch of active Power factor correction (PFC) techniques, the single-stage technique receives particular attention because of its low cost implementation. Moreover, with continuously demands for even higher power density, switching mode power supply operating at high-frequency is required because at high switching frequency, the size and weight of circuit components can be remarkably reduced. To boost the switching frequency, the soft-switching technique was introduced to alleviate the switching losses. The part two (chapter 5,6) of the dissertation presents several topologies for this front-end application. The design considerations, simulation results and experimental verification are discussed

Input-current shaped ac to dc converters

The problem of achieving near unity power factor while supplying power to a dc load from a single phase ac source of power is examined. Power processors for this application must perform three functions: input current shaping, energy storage, and output voltage regulation. The methods available for performing each of these three functions are reviewed. Input current shaping methods are either active or passive, with the active methods divided into buck-like and boost-like techniques. In addition to large reactances, energy storage methods include resonant filters, active filters, and active storage schemes. Fast voltage regulation can be achieved by post regulation or by supplementing the current shaping topology with an extra switch. Some indications of which methods are best suited for particular applications concludes the discussion

A double-sided silicon micro-strip super-module for the ATLAS inner detector upgrade in the high-luminosity LHC

The ATLAS experiment is a general purpose detector aiming to fully exploit the discovery potential of the Large Hadron Collider (LHC) at CERN. It is foreseen that after several years of successful data-taking, the LHC physics programme will be extended in the so-called High-Luminosity LHC, where the instantaneous luminosity will be increased up to 5 × 1034 cm−2 s−1. For ATLAS, an upgrade scenario will imply the complete replacement of its internal tracker, as the existing detector will not provide the required performance due to the cumulated radiation damage and the increase in the detector occupancy. The current baseline layout for the new ATLAS tracker is an all-silicon-based detector, with pixel sensors in the inner layers and silicon micro-strip detectors at intermediate and outer radii. The super-module is an integration concept proposed for the strip region of the future ATLAS tracker, where double-sided stereo silicon micro-strip modules are assembled into a low-mass local support structure. An electrical super-module prototype for eight double-sided strip modules has been constructed. The aim is to exercise the multi-module readout chain and to investigate the noise performance of such a system. In this paper, the main components of the current super-module prototype are described and its electrical performance is presented in detail