A 10-bit Charge-Redistribution ADC Consuming 1.9 μW at 1 MS/s

This paper presents a 10 bit successive approximation ADC in 65 nm CMOS that benefits from technology scaling. It meets extremely low power requirements by using a charge-redistribution DAC that uses step-wise charging, a dynamic two-stage comparator and a delay-line-based controller. The ADC requires no external reference current and uses only one external supply voltage of 1.0 V to 1.3 V. Its supply current is proportional to the sample rate (only dynamic power consumption). The ADC uses a chip area of approximately 115--225 μm2. At a sample rate of 1 MS/s and a supply voltage of 1.0 V, the 10 bit ADC consumes 1.9 μW and achieves an energy efficiency of 4.4 fJ/conversion-step

Noise shaping Asynchronous SAR ADC based time to digital converter

Time-to-digital converters (TDCs) are key elements for the digitization of timing information in modern mixed-signal circuits such as digital PLLs, DLLs, ADCs, and on-chip jitter-monitoring circuits. Especially, high-resolution TDCs are increasingly employed in on-chip timing tests, such as jitter and clock skew measurements, as advanced fabrication technologies allow fine on-chip time resolutions. Its main purpose is to quantize the time interval of a pulse signal or the time interval between the rising edges of two clock signals. Similarly to ADCs, the performance of TDCs are also primarily characterized by Resolution, Sampling Rate, FOM, SNDR, Dynamic Range and DNL/INL. This work proposes and demonstrates 2nd order noise shaping Asynchronous SAR ADC based TDC architecture with highest resolution of 0.25 ps among current state of art designs with respect to post-layout simulation results. This circuit is a combination of low power/High Resolution 2nd Order Noise Shaped Asynchronous SAR ADC backend with simple Time to Amplitude converter (TAC) front-end and is implemented in 40nm CMOS technology. Additionally, special emphasis is given on the discussion on various current state of art TDC architectures.Electrical and Computer Engineerin

High-Resolution ADCs Design in Image Sensors

This paper presents design considerations for high-resolution and high-linearity ADCs for biomedical imaging ap-plications. The work discusses how to improve dynamic spec-ifications such as Spurious Free Dynamic Range (SFDR) and Signal-to-Noise-and-Distortion Ratio (SNDR) in ultra-low power and high-resolution analog-to-digital converters (ADCs) including successive approximation register (SAR) for biomedical imaging application. The results show that with broad range of mismatch error, the SFDR is enhanced by about 10 dB with the proposed performance enhancement technique, which makes it suitable for high resolution image sensors sensing systems

Exploiting smallest error to calibrate non-linearity in SAR ADCs

This paper presents a statistics-optimised organisation technique to achieve better element matching in Successive Approximation Register (SAR) Analog-to-Digital Converter (ADC) in smart sensor systems. We demonstrate the proposed technique ability to achieve a significant improvement of around 23 dB on Spurious Free Dynamic Range (SFDR) of the ADC than the conventional, testing with a capacitor mismatch σu = 0.2% in a 14 bit SAR ADC system. For the static performance, the max root mean square (rms) value of differential nonlinearity (DNL) reduces from 1.63 to 0.20 LSB and the max rms value of integral nonlinearity (INL) reduces from 2.10 to 0.21 LSB. In addition, it is demonstrated that by applying grouping optimisation and strategy optimisation, the performance boosting on SFDR can be effectively achieved. Such great improvement on the resolution of the ADC only requires an off-line pre-processing digital part

Design and Simulation of an 8-Bit Successive Approximation Register Charge-Redistribution Analog-To-Digital Converter

The thesis initially investigates the history of the monolithic ADCs. The next chapter explores the different types of ADCs available in the market today. Next, the operation of a 4-bit SAR ADC has been studied. Based on this analysis, an 8-bit charge-redistribution SAR ADC has been designed and simulated with Multisim (National Instruments, Austin, TX). The design is divided into different blocks which are individually implemented and tested. Level-1 SPICE MOSFET models representative of 5μm devices were used wherever individual MOSFETs were used in the design. Finally, the power dissipation during the conversion period was also estimated. The supply voltage for the ADC is 5V and the clock frequency is 500KHz

An efficient tool for the assisted design of SAR ADCs capacitive DACs

The optimal design of SAR ADCs requires the accurate estimate of nonlinearity and parasitic capacitance effects in the feedback charge redistribution DAC. Since both contributions depend on the specific array topology, complex calculations, custom modeling and heavy simulations in common circuit design environments are often required. This paper presents a MATLAB-based numerical environment to assist the design of the charge redistribution DACs adopted in SAR ADCs. The tool performs both parametric and statistical simulations taking into account capacitive mismatch and parasitic capacitances computing both differential and integral nonlinearity (DNL, INL). An excellent agreement is obtained with the results of circuit simulators (e.g. Cadence Spectre) featuring up to 10^4 shorter simulation time, allowing statistical simulations that would be otherwise impracticable. The switching energy and SNDR degradation due to static nonlinear effects are also estimated. Simulations and measurements on three designed and two fabricated prototypes confirm that the proposed tool can be used as a valid instrument to assist the design of a charge redistribution SAR ADC and to predict its static and dynamic metrics

Capacitance-to-Digital Converter for Ultra-Low-Power Wireless Sensor Nodes

Power consumption is one of the main design constraints in today’s integrated circuits. For systems like wearable electronics, UAVs, IOT systems powered by batteries which are charged using the energy harvested from various sources like RF, Thermal, Solar and Vibration, ultra-low power consumption is paramount. In these systems, Transducers which convert physical parameters into electrical parameters and the analog-to-digital converters (ADCs) are key components as the interface between the analog world and the digital domain. This thesis addresses the design challenges, strategies, as well as circuit techniques of ultra-low-power signal Front End used in several low power electronic systems in general and pressure measurement systems in particular. In this thesis, Capacitance to Digital Converter based pressure measurement system has been implemented. Here we present a general-purpose, wide-range CDC that combines a correlated double sampling (CDS) approach with a differential asynchronous SAR ADC. Since the sensor capacitor is sampled only twice per conversion, energy per conversion is low. Furthermore, since the CDS separates the sensor capacitor from the CDAC, a full differential input voltage range is preserved. The CDC has a 2.5-to-75.5pF conversion range. Monotonic SAR ADC was designed in 180nm CMOS with 1-V power supply and a 1-kS/s sampling rate with switching energy of about 100nW

Low-Power SAR ADCs:Basic Techniques and Trends

With the advent of small, battery-powered devices, power efficiency has become of paramount importance. For analog-to-digital converters (ADCs), the successive approximation register (SAR) architecture plays a prominent role thanks to its ability to combine power efficiency with a simple architecture, a broad application scope, and technology portability. In this review article, the basic design challenges for low-power SAR ADCs are summarized and several design techniques are illustrated. Furthermore, the limitations of SAR ADCs are outlined and hybrid architecture trends, such as noise-shaping SAR ADCs and pipelined SAR ADCs, are briefly introduced and clarified with examples