Architectures, Antennas and Circuits for Millimeter-wave Wireless Full-Duplex Applications

Demand for wireless network capacity keeps growing exponentially every year, as a result a 1000-fold increase in data traffic is projected over the next 10 years in the context of 5G wireless networks. Solutions for delivering the 1000-fold increase in capacity fall into three main categories: deploying smaller cells, allocating more spectrum and improving spectral efficiency of wireless systems. Smaller cells at RF frequencies (1-6GHz) are unlikely to deliver the demanded capacity increase. On the other hand, millimeter-wave spectrum (frequencies over 24GHz) offers wider, multi-GHz channel bandwidths, and therefore has gained significant research interest as one of the most promising solutions to address the data traffic demands of 5G. Another disruptive technology is full-duplex which breaks a century-old assumption in wireless communication, by simultaneous transmission and reception on the same frequency channel. In doing so, full-duplex offers many benefits for wireless networks, including an immediate spectral efficiency improvement in the physical layer. Although FD promises great benefits, self-interference from the transmitter to its own receiver poses a fundamental challenge. The self-interference can be more than a billion times stronger than the desired signal and must be suppressed below the receiver noise floor. In recent years, there has been some research efforts on fully-integrated full-duplex RF transceivers, but mm-wave fully-integrated full-duplex systems, are still in their infancy. This dissertation presents novel architectures, antenna and circuit techniques to merge two exciting technologies, mm-wave and full-duplex, which can potentially offer the dual benefits of wide bandwidths and improved spectral efficiency. To this end, two different antenna interfaces, namely a wideband reconfigurable T/R antenna pair with polarization-based antenna cancellation and an mm-wave fully-integrated magnetic-free non-reciprocal circulator, are presented. The polarization-based antenna cancellation is employed in conjunction with the RF and digital cancellation to design a 60GHz full-duplex 45nm SOI CMOS transceiver with nearly 80dB self-interference suppression. The concepts and prototypes presented in this dissertation have also profound implications for emerging applications such as vehicular radars, 5G small-cell base-stations and virtual reality

Surpassing Fundamental Limits through Time Varying Electromagnetics

Surpassing the fundamental limits that govern all electromagnetic structures, such as reciprocity and the delay-bandwidth-size limit, will have a transformative impact on all applications based on electromagnetic circuits and systems. For instance, violating principles of reciprocity enables non-reciprocal components such as isolators and circulators, which find application in full-duplex wireless radios, radar, biomedical imaging, and quantum computing systems. Overcoming the delay-bandwidth-size limit enables ultra-broadband yet extremely-compact devices whose size is not fundamentally related to the wavelength at the operating frequency. The focus of this dissertation is on using time-variance as a new toolbox to overcome these fundamental limits and re-imagine circuit and system design. Traditional non-reciprocal components are realized using ferrite materials that loose their reciprocity under the application of external magnetic bias. However, the sheer volume, cost and weight of these magnet based non-reciprocal components coupled with their inability to be fabricated in conventional semiconductor processes, have limited their application to bulky and large-scale systems. Other approaches such as active-biased and non-linearity based non-reciprocity are compatible with semiconductor processes, however, they suffer from other poor linearity and noise performance. In this dissertation, using passive transistor switch as the modulating element, we have proposed the concept of spatio-temporal conductivity modulation and have demonstrated a gamut of non-reciprocal devices ranging from gyrators to isolators and circulators. Through novel circuit topologies, for the first time, we have demonstrated on-chip circulators with multi-watt input power handling, operation at high millimeter-wave frequencies, and tailor made circulators for emerging technologies such as simultaneous-transmit-and-receive MRI and quantum computing. Delay-bandwidth-size trade-off is another fundamental electromagnetic limit, that constrains the delay imparted by a medium or a device within a fixed footprint to be inversely proportional to the signal bandwidth. It is this limit that governs the size of any microwave passive devices to be inversely proportional to its operating frequency. As a part of this dissertation, through intelligent clocking of switched capacitor networks we overcame the delay-bandwidth-size limit, thus resulting in infinitesimal, yet broadband microwave devices. Here we proposed a new paradigm in wave propagation where the properties such as the propagation delay and characteristic impedance does not depend on the constituent elements/materials of the medium, but rather heavily rely on the user-defined modulation scheme, thereby opening huge opportunities for realizing highly-reconfigurable passives. Leveraging these concepts, we demonstrated wide range of reciprocal an non-reciprocal devices including ultra-compact delay elements, highly-reconfigurable microwave passives, ultra-wideband circulators with infinitesimal form-factors and dispersion-free chip scale floquet topological insulators. Application of these devices have also been evaluated in real-world systems through our demonstrations of wideband, full-duplex receivers leveraging switched capacitors based true-time-delay interference cancelers and floquet topological insulator based antenna interfaces for full-duplex phased-arrays and ultra-wideband beamformers. Furthermore, to cater the growing RF and microwave needs of future, large-scale quantum computing systems, we demonstrated a low-cryogenic, wideband circulator based on time modulation of superconducting devices. This superconducting circulator is expected to operate alongside the superconducting qubits, inside a dilution refrigerator at 10mK-100mK, thus enabling a tightly integrated quantum system. We also presented the design and implementation of a cryogenic-CMOS clock driver chip that will generate the clocks required by the superconducting circulator. Finally, we also demonstrated the design and implementation of a low-noise, low power consumption, 6GHz - 8GHz cryogenic downconversion receiver at 4K for cryogenic qubit readout

Scalable Array Transceivers with Wide Frequency Tuning Range for Next Generation Radios

Scalable array transceivers with wide frequency tuning range are attractive for next-generationradios. Key challenges for such radios include generation of LO signals with widefrequency tuning range, scalable synchronization between multiple array unit cells andtolerance to in-band and out-of-band interferers. This thesis presents approaches toaddress these challenges in commercial CMOS technologies.The first part focuses on a series resonant mode-switching VCO architecture thatachieves both state-of-art area and power efficiency with an octave frequency tuningrange from 6.4-14 GHz achieved 186-dB-188-dB Figure-of-Merit (FoM) in 65 nm CMOStechnology. The scalability of this approach towards achieving even larger FTR is alsodemonstrated by a triple-mode 2.2 GHz to 8.7 GHz (119% FTR) CMOS VCO.In the second part a scalable, single-wire coupled-PLL architecture for RF mm-wavearrays is presented. The proposed architecture preserves the simplicity of a daisy-chained LO distribution, compensates for phase offset due to interconnect, and provides phasenoise improvement commensurate to the number of coupled PLLs. Measurements on a28 GHz CMOS prototype demonstrate the feasibility of this scheme.The third part of this thesis presents filtering techniques for in-band blocker suppression.A spatial spectral notch filter design for MIMO digital beam forming arrays is proposedto relax the ADC dynamic range requirement. Orthogonal properties of Walsh functionsincorporated into passive N-path approach enables reconfigurable notches at multiplefrequencies and angles-of-incidence. A 0.3 GHz-1.4 GHz four-element array prototypeimplemented in 65 nm CMOS achieves > 15-dB notch filtering at RF input for twoblockers while causing < 3-dB NF degradation.Finally, a code-domain N-path receiver (RX) is proposed based on pseudo-random(PN) code-modulated LO pulses for simultaneous transmission and reception (STAR)applications. A combination of Walsh-Function and PN sequence is proposed to createcode-domain matched filter at the RF frontend which reflects unknown in-band blockersand rejects known in-band TX self-interference (SI) by using orthogonal codes at RXinput thereby maximizing the SNR of the received signals. The resulting prototype in65 nm is functional from 0.3 GHz-1.4 GHz with 35 dB gain and concurrently receivestwo code-modulated signals. Proposed transmitter (TX) SI mitigation approach resultsin 38.5 dB rejection for -11.8 dBm 1.46 Mb s QPSK modulated SI at RX input. TheRX achieves 23.7 dBm OP1dB for in-band SI, while consuming ∼35 mW and occupies0.31 mm2Keywords: Passive Mixers, dual band, TX self-Interferer, synchronisation, STAR, Code domain N-path receiver, mode switching, notch filter, Phase locked loops, Octave tuning range, CMOS, phase noise, VCO, large-scale 5G mm-wave arrays, resonator, Simultaneous transmit and receive, resonator band-switching, LO distribution, scalable coupled-PLL, N-path passive mixers, MIMO arrays, digital beamforming, CDMA, phased arrays, wide tuning range, Walsh Functio

Fully-Integrated Magnetic-Free Nonreciprocal Components by Breaking Lorentz Reciprocity: from Physics to Applications

Reciprocity is a fundamental physical precept that governs wave propagation in a wide variety of physical domains. The various reciprocity theorems state that the response of a system remains unchanged if the excitation source and the measuring point are interchanged within a medium, and are closely related to the concept of time reversal symmetry in physics. Lorentz reciprocity is a fundamental characteristic of linear, time-invariant electronic and photonic structures with symmetric permittivity and permeability tensors. However, breaking reciprocity enables the realization of nonreciprocal components, such as isolators and circulators, which are critical to electronic, optical and acoustic systems, as well as new functionalities and devices based on novel wave propagation modes. Nonreciprocal components have traditionally relied on magnetic materials such as ferrites that lose reciprocity under the application of an external magnetic field through the Faraday Effect. The need for a magnetic bias limits the applicability of such approaches in small-form-factor Complementary Metal–Oxide–Semiconductor (CMOS)-compatible integrated devices. One of the main features of CMOS technology is the availability of high-speed transistor switches which can be turned ON and OFF, modulating the conductance of the medium. In this dissertation, a novel approach to break Lorentz reciprocity is presented based on staggered commutation in Linear Periodically-Time-Varying (LPTV) circuits. We have demonstrated the world’s first CMOS passive magnetic-free nonreciprocal circulator through spatio-temporal conductivity modulation. Since conductivity in semiconductors can be modulated over a wide range (CMOS transistor ON/OFF conductance ratio at Radio Frequency (RF)/millimeter-wave frequencies is as high as 103-105), commutated LPTV networks break reciprocity within a deeply sub-wavelength form-factor with low loss and high linearity. The resulting nonreciprocal components find application in antenna interfaces of wireless communication systems, connecting the Transmitter (TX) and the Receiver (RX) to a shared antenna. This is particularly important for full-duplex wireless, where the TX and the RX operate simultaneously at the same frequency band and need to be highly isolated in order to maintain receiver sensitivity. Multiple fully-integrated full-duplex receivers are demonstrated in this dissertation that best show the synergy between the physical concept and application-based implementations by using circuit techniques to benefit the system-level performance, such as TX-side linearity enhancement and co-design and co-optimization of the antenna interface and the RX and utilization of the multi-phase structure of our antenna interfaces for analog beamforming in multi-antenna systems. Finally, this dissertation discusses some of the fundamental limits of space-time modulated nonreciprocal structures, as well as new directions to build nonreciprocal components which can ideally be infinitesimal in size. A novel family of inductor-less nonreciprocal components including circulators and isolators have been demonstrated that achieve a wide tuning range in an infinitesimal form-factor. This family of devices combine reciprocal and nonreciprocal modes of operation, through the transfer properties of fundamental and harmonics of the system and enable a wide variety of functionalities

Reconfigurable Receiver Front-Ends for Advanced Telecommunication Technologies

The exponential growth of converging technologies, including augmented reality, autonomous vehicles, machine-to-machine and machine-to-human interactions, biomedical and environmental sensory systems, and artificial intelligence, is driving the need for robust infrastructural systems capable of handling vast data volumes between end users and service providers. This demand has prompted a significant evolution in wireless communication, with 5G and subsequent generations requiring exponentially improved spectral and energy efficiency compared to their predecessors. Achieving this entails intricate strategies such as advanced digital modulations, broader channel bandwidths, complex spectrum sharing, and carrier aggregation scenarios. A particularly challenging aspect arises in the form of non-contiguous aggregation of up to six carrier components across the frequency range 1 (FR1). This necessitates receiver front-ends to effectively reject out-of-band (OOB) interferences while maintaining high-performance in-band (IB) operation. Reconfigurability becomes pivotal in such dynamic environments, where frequency resource allocation, signal strength, and interference levels continuously change. Software-defined radios (SDRs) and cognitive radios (CRs) emerge as solutions, with direct RF-sampling receivers offering a suitable architecture in which the frequency translation is entirely performed in digital domain to avoid analog mixing issues. Moreover, direct RF- sampling receivers facilitate spectrum observation, which is crucial to identify free zones, and detect interferences. Acoustic and distributed filters offer impressive dynamic range and sharp roll off characteristics, but their bulkiness and lack of electronic adjustment capabilities limit their practicality. Active filters, on the other hand, present opportunities for integration in advanced CMOS technology, addressing size constraints and providing versatile programmability. However, concerns about power consumption, noise generation, and linearity in active filters require careful consideration.This thesis primarily focuses on the design and implementation of a low-voltage, low-power RFFE tailored for direct sampling receivers in 5G FR1 applications. The RFFE consists of a balun low-noise amplifier (LNA), a Q-enhanced filter, and a programmable gain amplifier (PGA). The balun-LNA employs noise cancellation, current reuse, and gm boosting for wideband gain and input impedance matching. Leveraging FD-SOI technology allows for programmable gain and linearity via body biasing. The LNA's operational state ranges between high-performance and high-tolerance modes, which are apt for sensitivityand blocking tests, respectively. The Q-enhanced filter adopts noise-cancelling, current-reuse, and programmable Gm-cells to realize a fourth-order response using two resonators. The fourth-order filter response is achieved by subtracting the individual response of these resonators. Compared to cascaded and magnetically coupled fourth-order filters, this technique maintains the large dynamic range of second-order resonators. Fabricated in 22-nm FD-SOI technology, the RFFE achieves 1%-40% fractional bandwidth (FBW) adjustability from 1.7 GHz to 6.4 GHz, 4.6 dB noise figure (NF) and an OOB third-order intermodulation intercept point (IIP3) of 22 dBm. Furthermore, concerning the implementation uncertainties and potential variations of temperature and supply voltage, design margins have been considered and a hybrid calibration scheme is introduced. A combination of on-chip and off-chip calibration based on noise response is employed to effectively adjust the quality factors, Gm-cells, and resonance frequencies, ensuring desired bandpass response. To optimize and accelerate the calibration process, a reinforcement learning (RL) agent is used.Anticipating future trends, the concept of the Q-enhanced filter extends to a multiple-mode filter for 6G upper mid-band applications. Covering the frequency range from 8 to 20 GHz, this RFFE can be configured as a fourth-order dual-band filter, two bandpass filters (BPFs) with an OOB notch, or a BPF with an IB notch. In cognitive radios, the filter’s transmission zeros can be positioned with respect to the carrier frequencies of interfering signals to yield over 50 dB blocker rejection

Low Power Filtering Techniques for Wideband and Wireless Applications

This dissertation presents design and implementation of continuous time analog filters for two specific applications: wideband analog systems such as disk drive channel and low-power wireless applications. Specific focus has been techniques that reduce the power requirements of the overall system either through improvement in architecture or efficiency of the analog building blocks. The first problem that this dissertation addresses is the implementation of wideband filters with high equalization gain. An efficient architecture that realizes equalization zeros by combining available transfer functions associated with a biquadratic cell is proposed. A 330MHz, 5th order Gm-C lowpass Butterworth filter with 24dB boost is designed using the proposed architecture. The prototype fabricated in standard 0.35um CMOS process shows -41dB of IM3 for 250mV peak to peak swing with 8.6mW/pole of power dissipation. Also, an LC prototype implemented using similar architecture is discussed in brief. It is shown that, for practical range of frequency and SNR, LC based design is more power efficient than a Gm-C one, though at the cost of much larger area. Secondly, a complementary current mirror based building block is proposed, which pushes the limits imposed by conventional transconductors on the powerefficiency of Gm-C filters. Signal processing through complementary devices provides good linearity and Gm/Id efficiency and is shown to improve power efficiency by nearly 7 times. A current-mode 4th order Butterworth filter is designed, in 0.13um UMC technology, using the proposed building. It provides 54.2dB IM3 and 55dB SNR in 1.3GHz bandwidth while consuming as low as 24mW of power. All CMOS filter realization occupies a relatively small area and is well suited for integration in deep submicron technologies. Thirdly, a 20MHz, 68dB dynamic range active RC filter is presented. This filter is designed for a ten bit continuous time sigma delta ADC architecture developed specifically for fine-line CMOS technologies. Inverter based amplification and a common mode feedback for such amplifiers are discussed. The filter consumes 5mW of power and occupies an area of 0.07 mm2

Saw-Less radio receivers in CMOS

Smartphones play an essential role in our daily life. Connected to the internet, we can easily keep in touch with family and friends, even if far away, while ever more apps serve us in numerous ways. To support all of this, higher data rates are needed for ever more wireless users, leading to a very crowded radio frequency spectrum. To achieve high spectrum efficiency while reducing unwanted interference, high-quality band-pass filters are needed. Piezo-electrical Surface Acoustic Wave (SAW) filters are conventionally used for this purpose, but such filters need a dedicated design for each new band, are relatively bulky and also costly compared to integrated circuit chips. Instead, we would like to integrate the filters as part of the entire wireless transceiver with digital smartphone hardware on CMOS chips. The research described in this thesis targets this goal. It has recently been shown that N-path filters based on passive switched-RC circuits can realize high-quality band-select filters on CMOS chips, where the center frequency of the filter is widely tunable by the switching-frequency. As CMOS downscaling following Moore’s law brings us lower clock-switching power, lower switch on-resistance and more compact metal-to-metal capacitors, N-path filters look promising. This thesis targets SAW-less wireless receiver design, exploiting N-path filters. As SAW-filters are extremely linear and selective, it is very challenging to approximate this performance with CMOS N-path filters. The research in this thesis proposes and explores several techniques for extending the linearity and enhancing the selectivity of N-path switched-RC filters and mixers, and explores their application in CMOS receiver chip designs. First the state-of-the-art in N-path filters and mixer-first receivers is reviewed. The requirements on the main receiver path are examined in case SAW-filters are removed or replaced by wideband circulators. The feasibility of a SAW-less Frequency Division Duplex (FDD) radio receiver is explored, targeting extreme linearity and compression Irequirements. A bottom-plate mixing technique with switch sharing is proposed. It improves linearity by keeping both the gate-source and gate-drain voltage swing of the MOSFET-switches rather constant, while halving the switch resistance to reduce voltage swings. A new N-path switch-RC filter stage with floating capacitors and bottom-plate mixer-switches is proposed to achieve very high linearity and a second-order voltage-domain RF-bandpass filter around the LO frequency. Extra out-of-band (OOB) rejection is implemented combined with V-I conversion and zero-IF frequency down-conversion in a second cross-coupled switch-RC N-path stage. It offers a low-ohmic high-linearity current path for out-of-band interferers. A prototype chip fabricated in a 28 nm CMOS technology achieves an in-band IIP3 of +10 dBm , IIP2 of +42 dBm, out-of-band IIP3 of +44 dBm, IIP2 of +90 dBm and blocker 1-dB gain-compression point of +13 dBm for a blocker frequency offset of 80 MHz. At this offset frequency, the measured desensitization is only 0.6 dB for a 0-dBm blocker, and 3.5 dB for a 10-dBm blocker at 0.7 GHz operating frequency (i.e. 6 and 9 dB blocker noise figure). The chip consumes 38-96 mW for operating frequencies of 0.1-2 GHz and occupies an active area of 0.49 mm2. Next, targeting to cover all frequency bands up to 6 GHz and achieving a noise figure lower than 3 dB, a mixer-first receiver with enhanced selectivity and high dynamic range is proposed. Capacitive negative feedback across the baseband amplifier serves as a blocker bypassing path, while an extra capacitive positive feedback path offers further blocker rejection. This combination of feedback paths synthesizes a complex pole pair at the input of the baseband amplifier, which is up-converted to the RF port to obtain steeper RF-bandpass filter roll-off than the conventional up-converted real pole and reduced distortion. This thesis explains the circuit principle and analyzes receiver performance. A prototype chip fabricated in 45 nm Partially Depleted Silicon on Insulator (PDSOI) technology achieves high linearity (in-band IIP3 of +3 dBm, IIP2 of +56 dBm, out-of-band IIP3 = +39 dBm, IIP2 = +88 dB) combined with sub-3 dB noise figure. Desensitization due to a 0-dBm blocker is only 2.2 dB at 1.4 GHz operating frequency. IIFinally, to demonstrate the performance of the implemented blocker-tolerant receiver chip designs, a test setup with a real mobile phone is built to verify the sensitivity of the receiver chip for different practical blocking scenarios

Power-efficient current-mode analog circuits for highly integrated ultra low power wireless transceivers

In this thesis, current-mode low-voltage and low-power techniques have been applied to implement novel analog circuits for zero-IF receiver backend design, focusing on amplification, filtering and detection stages. The structure of the thesis follows a bottom-up scheme: basic techniques at device level for low voltage low power operation are proposed in the first place, followed by novel circuit topologies at cell level, and finally the achievement of new designs at system level. At device level the main contribution of this work is the employment of Floating-Gate (FG) and Quasi-Floating-Gate (QFG) transistors in order to reduce the power consumption. New current-mode basic topologies are proposed at cell level: current mirrors and current conveyors. Different topologies for low-power or high performance operation are shown, being these circuits the base for the system level designs. At system level, novel current-mode amplification, filtering and detection stages using the former mentioned basic cells are proposed. The presented current-mode filter makes use of companding techniques to achieve high dynamic range and very low power consumption with for a very wide tuning range. The amplification stage avoids gain bandwidth product achieving a constant bandwidth for different gain configurations using a non-linear active feedback network, which also makes possible to tune the bandwidth. Finally, the proposed current zero-crossing detector represents a very power efficient mixed signal detector for phase modulations. All these designs contribute to the design of very low power compact Zero-IF wireless receivers. The proposed circuits have been fabricated using a 0.5μm double-poly n-well CMOS technology, and the corresponding measurement results are provided and analyzed to validate their operation. On top of that, theoretical analysis has been done to fully explore the potential of the resulting circuits and systems in the scenario of low-power low-voltage applications.Programa Oficial de Doctorado en Tecnologías de las Comunicaciones (RD 1393/2007)Komunikazioen Teknologietako Doktoretza Programa Ofiziala (ED 1393/2007

Continuous-time low-pass filters for integrated wideband radio receivers

This thesis concentrates on the design and implementation of analog baseband continuous-time low-pass filters for integrated wideband radio receivers. A total of five experimental analog baseband low-pass filter circuits were designed and implemented as a part of five single-chip radio receivers in this work. After the motivation for the research work presented in this thesis has been introduced, an overview of analog baseband filters in radio receivers is given first. In addition, a review of the three receiver architectures and the three wireless applications that are adopted in the experimental work of this thesis is presented. The relationship between the integrator non-idealities and integrator Q-factor, as well as the effect of the integrator Q-factor on the filter frequency response, are thoroughly studied on the basis of a literature review. The theoretical study that is provided is essential for the gm-C filter synthesis with non-ideal lossy integrators that is presented after the introduction of different techniques to realize integrator-based continuous-time low-pass filters. The filter design approach proposed for gm-C filters is original work and one of the main points in this thesis, in addition to the experimental IC implementations. Two evolution versions of fourth-order 10-MHz opamp-RC low-pass filters designed and implemented for two multicarrier WCDMA base-station receivers in a 0.25-µm SiGe BiCMOS technology are presented, along with the experimental results of both the low-pass filters and the corresponding radio receivers. The circuit techniques that were used in the three gm-C filter implementations of this work are described and a common-mode induced even-order distortion in a pseudo-differential filter is analyzed. Two evolution versions of fifth-order 240-MHz gm-C low-pass filters that were designed and implemented for two single-chip WiMedia UWB direct-conversion receivers in a standard 0.13-µm and 65-nm CMOS technology, respectively, are presented, along with the experimental results of both the low-pass filters and the second receiver version. The second UWB filter design was also embedded with an ADC into the baseband of a 60-GHz 65-nm CMOS radio receiver. In addition, a third-order 1-GHz gm-C low-pass filter was designed, rather as a test structure, for the same receiver. The experimental results of the receiver and the third gm-C filter implementation are presented

Wave transport in parity-time symmetric, time-varying, and quasi-periodic systems

The past several decades have witnessed a rapid growth of research interest in the fields of artificial materials and systems, in particular in the areas of parity-time symmetric systems, time-varying systems and quasi-periodic systems. These newly developed material platforms have been enabling many exotic wave-matter interaction phenomena unavailable in nature. In this context, I investigated a series of wave transport and scattering phenomena in parity-time symmetric, time-varying and quasi periodic systems in this dissertation. First, I proposed a sensing circuit based on sixth-order exceptional point (EP), which supports high sensitivity, resolution, and nondegraded thermal noise performance compared with conventional diabolic point (DP) sensing system. I also studied the influence of thermal noise in a general two-level sensing platform based on EP. Second, I demonstrated a robust microwave tunneling device operating in the extreme case in which the transmission channel is shorted through a small reactance. We observed full restoration of information and overall transparency to an external observer through use of a pair of parity-time-symmetric emitter and absorber. Third, I studied the effects of realistic switching parameters and synchronization in a series of nonreciprocal devices based on synchronized loss modulation. The research showed that the nonreciprocal response of these systems experiences a linear regression of insertion loss and isolation with respect to the timing error among switches. Remarkably, impedance matching, and nonreciprocal phase shifts are immune from synchronization issues, and reasonable levels of synchronization errors still guarantee low insertion loss and good isolation. Fourth, I studied wave scattering phenomena in static and dynamic quasi-periodic LC resonator array, which provides an easily accessible and reconfigurable platform to study fractal energy band and topological edge state. Overall, my explorations have been enabling a new degree of control of waves in circuits and metamaterials, pushing forward the opportunities for extreme wave-matter interactions using gain and time modulations.Electrical and Computer Engineerin