Insights into tunnel FET-based charge pumps and rectifiers for energy harvesting applications

In this paper, the electrical characteristics of tunnel field-effect transistor (TFET) devices are explored for energy harvesting front-end circuits with ultralow power consumption. Compared with conventional thermionic technologies, the improved electrical characteristics of TFET devices are expected to increase the power conversion efficiency of front-end charge pumps and rectifiers powered at sub-µW power levels. However, under reverse bias conditions the TFET device presents particular electrical characteristics due to its different carrier injection mechanism. In this paper, it is shown that reverse losses in TFET-based circuits can be attenuated by changing the gate-to-source voltage of reverse-biased TFETs. Therefore, in order to take full advantage of the TFETs in front-end energy harvesting circuits, different circuit approaches are required. In this paper, we propose and discuss different topologies for TFET-based charge pumps and rectifiers for energy harvesting applications.Peer ReviewedPostprint (author's final draft

Architecture of Micro Energy Harvesting Using Hybrid Input of RF, Thermal and Vibration for Semi-Active RFID Tag

This research work presents a novel architecture of Hybrid Input Energy Harvester (HIEH) system for semi-active Radio Frequency Identification (RFID) tags. The proposed architecture consists of three input sources of energy which are radio frequency signal, thermal and vibration. The main purpose is to solve the semi-active RFID tags limited lifespan issues due to the need for batteries to power their circuitries. The focus will be on the rectifiers and DC-DC converter circuits with an ultra-low power design to ensure low power consumption in the system. The design architecture will be modelled and simulated using PSpice software, Verilog coding using Mentor Graphics and real-time verification using field-programmable gate array board before being implemented in a 0.13 µm CMOS technology. Our expectations of the results from this architecture are it can deliver 3.3 V of output voltage, 6.5 mW of output power and 90% of efficiency when all input sources are simultaneously harvested. The contribution of this work is it able to extend the lifetime of semi-active tag by supplying electrical energy continuously to the device. Thus, this will indirectly  reduce the energy limitation problem, eliminate the dependency on batteries and make it possible to achieve a batteryless device.This research work presents a novel architecture of Hybrid Input Energy Harvester (HIEH) system for semi-active Radio Frequency Identification (RFID) tags. The proposed architecture consists of three input sources of energy which are radio frequency signal, thermal and vibration. The main purpose is to solve the semi-active RFID tags limited lifespan issues due to the need for batteries to power their circuitries. The focus will be on the rectifiers and DC-DC converter circuits with an ultra-low power design to ensure low power consumption in the system. The design architecture will be modelled and simulated using PSpice software, Verilog coding using Mentor Graphics and real-time verification using field-programmable gate array board before being implemented in a 0.13 µm CMOS technology. Our expectations of the results from this architecture are it can deliver 3.3 V of output voltage, 6.5 mW of output power and 90% of efficiency when all input sources are simultaneously harvested. The contribution of this work is it able to extend the lifetime of semi-active tag by supplying electrical energy continuously to the device. Thus, this will indirectly  reduce the energy limitation problem, eliminate the dependency on batteries and make it possible to achieve a batteryless device

A Survey of Multi-Source Energy Harvesting Systems

Energy harvesting allows low-power embedded devices to be powered from naturally-ocurring or unwanted environmental energy (e.g. light, vibration, or temperature difference). While a number of systems incorporating energy harvesters are now available commercially, they are specific to certain types of energy source. Energy availability can be a temporal as well as spatial effect. To address this issue, ‘hybrid’ energy harvesting systems combine multiple harvesters on the same platform, but the design of these systems is not straightforward. This paper surveys their design, including trade-offs affecting their efficiency, applicability, and ease of deployment. This survey, and the taxonomy of multi-source energy harvesting systems that it presents, will be of benefit to designers of future systems. Furthermore, we identify and comment upon the current and future research directions in this field

A miniaturised autonomous sensor based on nanowire materials platform: the SiNAPS mote

A micro-power energy harvesting system based on core(crystalline Si)-shell(amorphous Si) nanowire solar cells together with a nanowire-modified CMOS sensing platform have been developed to be used in a dust-sized autonomous chemical sensor node. The mote (SiNAPS) is augmented by low-power electronics for power management and sensor interfacing, on a chip area of 0.25mm2. Direct charging of the target battery (e.g., NiMH microbattery) is achieved with end-to-end efficiencies up to 90% at AM1.5 illumination and 80% under 100 times reduced intensity. This requires matching the voltages of the photovoltaic module and the battery circumventing maximum power point tracking. Single solar cells show efficiencies up to 10% under AM1.5 illumination and open circuit voltages, Voc, of 450-500mV. To match the battery’s voltage the miniaturised solar cells (~1mm2 area) are connected in series via wire bonding. The chemical sensor platform (mm2 area) is set up to detect hydrogen gas concentration in the low ppm range and over a broad temperature range using a low power sensing interface circuit. Using Telran TZ1053 radio to send one sample measurement of both temperature and H2 concentration every 15 seconds, the average and active power consumption for the SiNAPS mote are less than 350nW and 2.1 μW respectively. Low-power miniaturised chemical sensors of liquid analytes through microfluidic delivery to silicon nanowires are also presented. These components demonstrate the potential of further miniaturization and application of sensor nodes beyond the typical physical sensors, and are enabled by the nanowire materials platform

Self-Powered, Highly Sensitive, High Speed Photodetection Using ITO/WSe2/SnSe2 Vertical Heterojunction

Two dimensional transition metal di-chalcogenides (TMDCs) are promising candidates for ultra-low intensity photodetection. However, the performance of these photodetectors is usually limited by ambience induced rapid performance degradation and long lived charge trapping induced slow response with a large persistent photocurrent when the light source is switched off. Here we demonstrate an indium tin oxide (ITO)/WSe$_2$/SnSe$_2$ based vertical double heterojunction photoconductive device where the photo-excited hole is confined in the double barrier quantum well, whereas the photo-excited electron can be transferred to either the ITO or the SnSe$_2$ layer in a controlled manner. The intrinsically short transit time of the photoelectrons in the vertical double heterojunction helps us to achieve high responsivity in excess of $1100$ A/W and fast transient response time on the order of $10$ $\mu$s. A large built-in field in the WSe$_2$ sandwich layer results in photodetection at zero external bias allowing a self-powered operation mode. The encapsulation from top and bottom protects the photo-active WSe$_2$ layer from ambience induced detrimental effects and substrate induced trapping effects helping us to achieve repeatable characteristics over many cycles

PhyNetLab: An IoT-Based Warehouse Testbed

Future warehouses will be made of modular embedded entities with communication ability and energy aware operation attached to the traditional materials handling and warehousing objects. This advancement is mainly to fulfill the flexibility and scalability needs of the emerging warehouses. However, it leads to a new layer of complexity during development and evaluation of such systems due to the multidisciplinarity in logistics, embedded systems, and wireless communications. Although each discipline provides theoretical approaches and simulations for these tasks, many issues are often discovered in a real deployment of the full system. In this paper we introduce PhyNetLab as a real scale warehouse testbed made of cyber physical objects (PhyNodes) developed for this type of application. The presented platform provides a possibility to check the industrial requirement of an IoT-based warehouse in addition to the typical wireless sensor networks tests. We describe the hardware and software components of the nodes in addition to the overall structure of the testbed. Finally, we will demonstrate the advantages of the testbed by evaluating the performance of the ETSI compliant radio channel access procedure for an IoT warehouse

In-Body Energy Harvesting Power Management Interface for Post Heart Transplantation Monitoring

Deep tissue energy harvesters are of increasing interest in the development of battery-less implantable devices. This paper presents a fully integrated ultra-low quiescent power management interface. It has power optimization and impedance matching between a piezoelectric energy harvester and the functional load that could be potentially powered by the heart's mechanical motions. The circuit has been designed in 0.18-µm CMOS technology. It dissipates 189.8 nW providing two voltage outputs of 1.4 V and 4.2 V. The simulation results show an output power 8.2x times of an ideal full-bridge rectifier without an external power supply. The design has the potential for use in self-powered heart implantable devices as it is capable providing stable output voltages from a cold startup