Baseband analog front-end and digital back-end for reconfigurable multi-standard terminals

Multimedia applications are driving wireless network operators to add high-speed data services such as Edge (E-GPRS), WCDMA (UMTS) and WLAN (IEEE 802.11a,b,g) to the existing GSM network. This creates the need for multi-mode cellular handsets that support a wide range of communication standards, each with a different RF frequency, signal bandwidth, modulation scheme etc. This in turn generates several design challenges for the analog and digital building blocks of the physical layer. In addition to the above-mentioned protocols, mobile devices often include Bluetooth, GPS, FM-radio and TV services that can work concurrently with data and voice communication. Multi-mode, multi-band, and multi-standard mobile terminals must satisfy all these different requirements. Sharing and/or switching transceiver building blocks in these handsets is mandatory in order to extend battery life and/or reduce cost. Only adaptive circuits that are able to reconfigure themselves within the handover time can meet the design requirements of a single receiver or transmitter covering all the different standards while ensuring seamless inter-interoperability. This paper presents analog and digital base-band circuits that are able to support GSM (with Edge), WCDMA (UMTS), WLAN and Bluetooth using reconfigurable building blocks. The blocks can trade off power consumption for performance on the fly, depending on the standard to be supported and the required QoS (Quality of Service) leve

The Development of TIGRA: A Zero Latency Interface For Accelerator Communication in RISC-V Processors

Field programmable gate arrays (FPGA) give developers the ability to design application specific hardware by means of software, providing a method of accelerating algorithms with higher power efficiency when compared to CPU or GPU accelerated applications. FPGA accelerated applications tend to follow either a loosely coupled or tightly coupled design. Loosely coupled designs often use OpenCL to utilize the FPGA as an accelerator much like a GPU, which provides a simplifed design flow with the trade-off of increased overhead and latency due to bus communication. Tightly coupled designs modify an existing CPU to introduce instruction set extensions to provide a minimal latency accelerator at the cost of higher programming effort to include the custom design. This dissertation details the design of the Tightly Integrated, Generic RISC-V Accelerator (TIGRA) interface which provides the benefits of both loosely and tightly coupled accelerator designs. TIGRA enabled designs incur zero latency with a simple-to-use interface that reduces programming effort when implementing custom logic within a processor. This dissertation shows the incorporation of TIGRA into the simple PicoRV32 processor, the highly customizable Rocket Chip generator, and the FPGA optimized Taiga processor. Each processor design is tested with AES 128-bit encryption and posit arithmetic to demonstrate TIGRA functionality. After a one time programming cost to incorporate a TIGRA interface into an existing processor, new functional units can be added with up to a 75% reduction in the lines of code required when compared to non-TIGRA enabled designs. Additionally, each functional unit created is co-compatible with each processor as the TIGRA interface remains constant between each design. The results prove that using the TIGRA interface introduces no latency and is capable of incorporating existing custom logic designs without modification for all three processors tested. When compared to the PicoRV32 coprocessor interface (PCPI), TIGRA coupled designs complete one clock cycle faster. Similarly, TIGRA outperforms the Rocket Chip custom coprocessor (RoCC) interface by an average of 6.875 clock cycles per instruction. The Taiga processor\u27s decoupled execution units allow for instructions to execute concurrently and uses a tag management system that is similar to out-of-order processors. The inclusion of the TIGRA interface within this processor abstracts the tag management from the user and demonstrates that the TIGRA interface can be applied to out-of-order processors. When coupled with partial reconfiguration, the flexibility and modularity of TIGRA drastically increases. By creating a reprogrammable region for the custom logic connected via TIGRA, users can swap out the connected design at runtime to customize the processor for a given application. Further, partial reconfiguration allows users to only compile the custom logic design as opposed to the entire CPU, resulting in an 18.1% average reduction of compilation during the design process in the case studies. Paired with the programming effort saved by using TIGRA, partial reconfiguration improves the time to design and test new functionality timelines for a processor