Integrated Circuit and System Design for Cognitive Radio and Ultra-Low Power Applications

The ubiquitous presence of wireless and battery-powered devices is an inseparable and invincible feature of our modern life. Meanwhile, the spectrum aggregation, and limited battery capacity of handheld devices challenge the exploding demand and growth of such radio systems. In this work, we try to present two separate solutions for each case; an ultra-wideband (UWB) receiver for Cognitive Radio (CR) applications to deal with spectrum aggregation, and an ultra-low power (ULP) receiver to enhance battery life of handheld wireless devices. Limited linearity and LO harmonics mixing are two major issues that ultra-wideband receivers, and CR in particular, are dealing with. Direct conversion schemes, based on current-driven passive mixers, have shown to improve the linearity, but unable to resolve LO harmonic mixing problem. They are usually limited to 3rd, and 5th harmonics rejection or require very complex and power hungry circuitry for higher number of harmonics. This work presents a heterodyne up-down conversion scheme in 180 nm CMOS technology for CR applications (54-862 MHz band) that mitigates the harmonic mixing issue for all the harmonics, while by employing an active feedback loop, a comparable to the state-of-the art IIP3 of better than +10 dBm is achieved. Measurements show an average NF of 7.5 dB when the active feedback loop is off (i.e. in the absence of destructive interference), and 15.5 dB when the feedback loop is active and a 0 dBm interferer is applied, respectively. Also, the second part of this work presents an ultra-low power super-regenerative receiver (SRR) suitable for OOK modulation and provides analytical insight into its design procedure. The receiver is fabricated in 40 nm CMOS technology and operates in the ISM band of 902-928 MHz. Binary search algorithm through Successive Approximation Register (SAR) architecture is being exploited to calibrate the internally generated quench signal and the working frequency of the receiver. Employing an on-chip inductor and a single-ended to differential architecture for the input amplifier has made the receiver fully integrable, eliminating the need for external components. A power consumption of 320 µW from a 0.65 V supply results in an excellent energy efficiency of 80 pJ/b at 4 Mb/s data rate. The receiver also employs an ADC that enables soft-decisioning and a convenient sensitivity-data rate trade-off, achieving sensitivity of -86.5, and -101.5 dBm at 1000 and 31.25 kbps data rate, respectivel

Integrated Circuit and System Design for Cognitive Radio and Ultra-Low Power Applications

The ubiquitous presence of wireless and battery-powered devices is an inseparable and invincible feature of our modern life. Meanwhile, the spectrum aggregation, and limited battery capacity of handheld devices challenge the exploding demand and growth of such radio systems. In this work, we try to present two separate solutions for each case; an ultra-wideband (UWB) receiver for Cognitive Radio (CR) applications to deal with spectrum aggregation, and an ultra-low power (ULP) receiver to enhance battery life of handheld wireless devices. Limited linearity and LO harmonics mixing are two major issues that ultra-wideband receivers, and CR in particular, are dealing with. Direct conversion schemes, based on current-driven passive mixers, have shown to improve the linearity, but unable to resolve LO harmonic mixing problem. They are usually limited to 3rd, and 5th harmonics rejection or require very complex and power hungry circuitry for higher number of harmonics. This work presents a heterodyne up-down conversion scheme in 180 nm CMOS technology for CR applications (54-862 MHz band) that mitigates the harmonic mixing issue for all the harmonics, while by employing an active feedback loop, a comparable to the state-of-the art IIP3 of better than +10 dBm is achieved. Measurements show an average NF of 7.5 dB when the active feedback loop is off (i.e. in the absence of destructive interference), and 15.5 dB when the feedback loop is active and a 0 dBm interferer is applied, respectively. Also, the second part of this work presents an ultra-low power super-regenerative receiver (SRR) suitable for OOK modulation and provides analytical insight into its design procedure. The receiver is fabricated in 40 nm CMOS technology and operates in the ISM band of 902-928 MHz. Binary search algorithm through Successive Approximation Register (SAR) architecture is being exploited to calibrate the internally generated quench signal and the working frequency of the receiver. Employing an on-chip inductor and a single-ended to differential architecture for the input amplifier has made the receiver fully integrable, eliminating the need for external components. A power consumption of 320 µW from a 0.65 V supply results in an excellent energy efficiency of 80 pJ/b at 4 Mb/s data rate. The receiver also employs an ADC that enables soft-decisioning and a convenient sensitivity-data rate trade-off, achieving sensitivity of -86.5, and -101.5 dBm at 1000 and 31.25 kbps data rate, respectivel

Superregeneration revisited: from principles to current applications

© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works.Wireless communications play a central role in our modern connected lives; at the same time, they constitute a very broad and deep area of research. The elements that make wireless communications possible are a transmitter, which sends information through electromagnetic waves; a medium that is able to transport these waves; and, finally, a receiver, which extracts the information from the-usually very small-amount of energy it is able to collect from the medium.Peer ReviewedPostprint (author's final draft

Low power rf transceivers

This thesis details the analysis and design of ultra-low power radio transceivers operating at microwave frequencies. Hybrid prototypes and Monolithic Microwave Integrated Circuits (MMICs) which achieve power consumptions of less than 1 mW and theoretical operating ranges of over 10 m are described. The motivation behind the design of circuits exhibiting ultra low power consumption and, in the case of the MMICs, small size is the emerging technology of Wireless Sensor Networks (WSN). WSNs consist of spatially distributed ‘nodes’ or ‘specks’ each with their own renewable energy source, one or more sensors, limited memory, processing capability and radio or optical link. The idea is that specks within a ‘speckzone’ cooperate and share computational resources to perform complex tasks such as monitoring fire hazards, radiation levels or for motion tracking. The radio section must be ultra low power e.g. sub 1 mW in order not to drain the limited battery capacity. The radio must also be small in size e.g. less than 5 x 5 mm so that the overall speck size is small. Also, the radio must still be able to operate over a range of at least a metre so as to allow radio contact between, for example, rooms or relatively distant specks. The unsuitability of conventional homodyne topologies to WSNs is discussed and more efficient methods of modulation (On-Off Keying) and demodulation (non-coherent) are presented. Furthermore, it is shown how Super-Regenerative Receivers (SRR) can be used to achieve relatively large output voltages for small input powers. This is important because baseband Op-Amps connected at the RF receiver output generally cannot amplify small signals at the input without the output being saturated in noise (10mV is the smallest measured input for 741 Op-Amp). Instrumentation amplifiers are used in this work as they can amplify signals below 1mV. The thesis details the analysis and design of basic RF building blocks: amplifiers, oscillators, switches and detectors. It also details how the circuits can be put together to make transceivers as well as describing various strategies to lower power consumption. In addition, novel techniques in both circuit and system design are presented which allow the power consumption of the radio to be reduced by as much as 97% whilst still retaining adequate performance. These techniques are based on duty cycling the transmitter and receiver and are possible because of the discontinuous nature of the On-Off Keying signal. In order to ease the sensitivity requirements of the baseband receive amplifier a design methodology for large output voltage receivers is presented. The designed receiver is measured to give a 5 mV output for an input power of -90 dBm and yet consumes less than 0.7 mW. There is also an appendix on the non linear modelling of the Glasgow University 50nm InP meta-morphic High Electron Mobility Transistor (50nm mHEMT) and one on the non linear modelling of a commercial Step Recovery diode (SRD). Models for the 50 nm mHEMT and the SRD are useful in the analysis, simulation and design of oscillators and pulse generators respectively

RF TRANSCEIVER DESIGN FOR WIRELESS SENSOR NETWORKS

Ph.DDOCTOR OF PHILOSOPH

Energy Aware RF Transceiver for Wireless Body Area Networks (WBAN)

Ph.DDOCTOR OF PHILOSOPH

의료용 인체 삽입물을 위한 무선 저전력 송수신기에 관한 연구

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2016. 2. 남상욱.This thesis presents the wireless transceiver for medical implant application. The high propagation loss in human body which has high relative permittivity and conductive makes the implantable device be required for high sensitivity. Moreover, the device should have low power consumption to use for wireless implant medical application due to a restricted battery life. Also, this problem should be solved for on-body device considering integration with mobile device in the future. Simultaneously, the specific medical application such as epiretinal prosthesis, multi-channel electroencephalogram sensor demand high-data rate. Therefore, it is a main challenge that enhancing the devices power consumption and data-rate for implantable medical application. In order to enhance the performance of the device, several techniques are proposed in implantable human body transceivers. Firstly, the propagation loss in human-body is calculated for determine the frequency for medical implant application. The frequency bands allocated by FCC or MICS are too narrow and high lossy bands in human-body. For this reason, the optimum frequency for Implantable medical device is found by using Frisss formula and the link budget is calculated for capsule endoscopy system. The optimum frequency is verified through image recovery experiment in liquid human phantom and pig by using designed capsule endoscopy system. Secondly, the Super-Regenerative Receiver (SRR) with Digital Self-Quenching Loop (DSQL) is proposed for low power consumption. The proposed DSQL replaces the envelope detector used in a conventional SRR and minimizes power consumption by generating a self-quench signal digitally for a super-regenerative oscillator. The measurement results are given to show the performance of the proposed receiver. Thirdly, the RF Current Reused and Current Combining (CRCC) Power Amplifier (PA) is proposed for low power and high-speed transmitter. Normally, the PA having low output power has a feasibility issue that an optimum impedance of PA is too high to match with antenna impedance. For this reason, obtaining the maximum efficiency of PA is difficult for conventional structure. Moreover, conventional PAs output bandwidth is to be narrow due to high impedance transform ratio between PAs output and antennas input impedances. The CRCC structure solves this issue by decreasing the impedance transform ratio. The transmitter with CRCC PA is designed and verified through the measurement.Chapter 1. Introduction 1 1.1. WBAN (Wireless Body Area Network) 1 1.2. Challenges in Designing Transceiver for Medical Implant Application 7 Chapter 2. Propagation Loss in Human Body 10 2.1. Introduction 10 2.2. Far field approximation in human-body 13 2.3. Calculation of propagation loss in human-body 15 2.3.1. Frisss formula 15 2.3.2. Efficiency of transmitting antenna in human-body 17 2.4. Calculation of propagation loss in human-body and conclusion 19 Chapter 3. A Design of Transceiver for Capsule Endoscopy Application 21 3.1. Introduction 21 3.2. System Link Budget Calculation 24 3.3. Implementation 26 3.3.1. Transmitter with class B amplifier 26 3.3.2. Super-heterodyne receiver with AGC 28 3.3.3. Measurement results 30 3.4. Image recovery experiment 35 3.4.1. Integration of capsule endoscopy 35 3.4.2. Image recovery in the liquid human phantom 38 3.4.3. Image recovery in a pigs stomach and large intestine 40 3.5. Conclusion 41 Chapter 4. Super-Regenerative Receiver with Digitally Self-Quenching Loop 42 4.1. Introduction 42 4.1.1. Selection of receivers architecture for implantable medical device 44 4.1.2. Previous study of super-regenerative receiver 50 4.2. Main idea of proposed super-regenerative receiver 51 4.3. Description of proposed receiver 53 4.3.1. Digital self-quenching loop 55 4.3.2. Low noise amplifier and super-regenerative oscillator 57 4.3.3. Active RC filter for low power consumption 59 4.4. Experimental results 63 4.5. Summary and conclusion 69 Chapter 5. A Transmitter with Current-Reused and Current-Combining PA 71 5.1. Introduction 71 5.1.1. Previous study of OOK transmitter 72 5.2. Main idea of proposed transmitter 73 5.3. Description of proposed transmitter 79 5.3.1. Current-combining and current-reused PA 79 5.3.2. Ring oscillator with driving buffer 83 5.4. Experimental Results 85 5.5. Summary and conclusion 93 Chapter 6. Conclusion 95 Chapter 7. Appendix 97 7.1. Output spectrum of OOK signal 97 7.2. Theoretical BER of OOK comunication 99 Bibliography 101 초 록 109Docto

Low power receivers for wireless sensor networks

Wireless sensor networks are becoming important in several monitoring and sensing applications. Ultra low power consumption in the sensor nodes is important for extending the battery life of the nodes. In this dissertation, two low power BFSK receiver architectures are proposed and verified with prototype implementations in silicion. A 2.4 GHz 1 Mb/s polyphase filter (PPF) BFSK receiver demonstrates ±180 ppm frequency offset tolerance (FOT) and 40 dB adjacent channel rejection (ACR) at a modulation index (MI) of 2, with a power consumption of 1.9 mW. High FOT at low MI is achieved by a frequency-to-energy conversion architecture using PPFs without any frequency correction. The proposed hybrid topology of the PPF provides an improved ACR at reduced power. To further improve the energy efficiency, a low energy 900 MHz mixer-less BFSK receiver is designed. High gain frequency-to-amplitude conversion and better sensitivity is achieved by a linear amplifier with Q-enhanced LC tank, eliminating the need for local oscillators and mixers. With a power consumption of 500 μW, the receiver achieves sensitivities of -90 dBm and -76 dBm for data rates of 0.5 Mb/s and 6 Mb/s, respectively. The energy efficiency is 80 pJ/b when operating at 6 Mb/s

A Fully Integrated CMOS Receiver.

The rapidly growing wireless communication market is creating an increasing demand for low-cost highly-integrated radio frequency (RF) communication systems. This dissertation focuses on techniques to enable fully-integrated, wireless receivers incorporating all passive components, including the antenna, and also incorporating baseband synchronization on-chip. Not only is the receiver small in size and requires very low power, but it also delivers synchronized demodulated data. This research targets applications such as implantable neuroprosthetic devices and environmental wireless sensors, which need short range, low data-rate wireless communications but a long lifetime. To achieve these goals, the super-regenerative architecture is used, since power consumption with this architecture is low due to the simplified receiver architecture. This dissertation presents a 5GHz single chip receiver incorporating a compact on-chip 5 GHz slot antenna (50 times smaller than traditional dipole antennas) and a digital received data synchronization. A compact capacitively-loaded 5 GHz standing-wave resonator is used to improve the energy efficiency. An all-digital PLL timing scheme synchronizes the received data clock. A new type of low-power envelope detector is incorporated to increase the data rate and efficiency. The receiver achieves a data rate up to 1.2 Mb/s, dissipates 6.6 mW from a 1.5 V supply. The novel on-chip capacitively-loaded, transmission-line-standing-wave resonator is employed instead of a conventional low-Q on-chip inductor. The simulated quality factor of the resonator is very high (35), and is verified by phase-noise measurements of a prototype 5GHz Voltage Control Oscillator (VCO) incorporating this resonator. The prototype VCO, implemented in 0.13 µm CMOS, dissipates 3 mW from a 1.2 V supply, and achieves a measured phase noise of -117 dBc/Hz at a 1 MHz offset. In the on-chip antenna an efficient shielding technique is used to shield the antenna from the low-resistivity substrate underneath. Two standalone on-chip slot antenna prototypes were designed and fabricated in 0.13 µm CMOS. The 9 GHz prototype occupies a die area of only 0.3 mm2, has an active gain of -4.4 dBi and an efficiency of 9%. The second prototype occupies a die area of 0.47 mm2, and achieves a passive gain of approximately -17.0 dBi at 5 GHz.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/60739/1/shid_1.pd