A 90 nm CMOS 16 Gb/s Transceiver for Optical Interconnects

Interconnect architectures which leverage high-bandwidth optical channels offer a promising solution to address the increasing chip-to-chip I/O bandwidth demands. This paper describes a dense, high-speed, and low-power CMOS optical interconnect transceiver architecture. Vertical-cavity surface-emitting laser (VCSEL) data rate is extended for a given average current and corresponding reliability level with a four-tap current summing FIR transmitter. A low-voltage integrating and double-sampling optical receiver front-end provides adequate sensitivity in a power efficient manner by avoiding linear high-gain elements common in conventional transimpedance-amplifier (TIA) receivers. Clock recovery is performed with a dual-loop architecture which employs baud-rate phase detection and feedback interpolation to achieve reduced power consumption, while high-precision phase spacing is ensured at both the transmitter and receiver through adjustable delay clock buffers. A prototype chip fabricated in 1 V 90 nm CMOS achieves 16 Gb/s operation while consuming 129 mW and occupying 0.105 mm^2

A study of Radiation-Tolerant Voltage-Controlled Oscillators designs in 65 nm bulk and 28 nm FDSOI CMOS technologies

Phase-locked loop (PLL) systems are widely employed in integrated circuits for space analog devices and communications systems that operate in radiation environments, where significant perturbations, especially in terms of phase noise, can be generated due to radiation particles. Among all the blocks that form a PLL system, previous research suggests the voltage-controlled oscillator (VCO) is one of the most critical components in terms of radiation tolerance and electric performance. Ring oscillators (ROs) and LC-tank VCOs have been commonly employed in high-performance PLLs. Nevertheless, both structures have drawbacks including a limited tuning range, high sensitivity to phase noise, limited radiation tolerance, and large design areas. In order to fulfill these high-performance requirements, a current-model logic (CML) based RO-VCO is presented as a possible solution capable of reducing the limitations of the commonly used structures and exploiting their advantages. The proposed hybrid VCO model includes passive components in its design which are the key parameters that define oscillation frequency of this structure. This tunable oscillator has been designed and tested in 65nm Bulk and 28 nm Fully depleted silicon-on-insulator (FDSOI) CMOS technologies The 65nm testchip was designed to compare the behavior of the proposed CML VCO with a current-starved RO and a radiation hardened by design (RHBD) LC-tank VCO in terms of tuning range, phase noise, Single event effect (SEE) sensitivity and design area. Simulations were carried out by applying a double exponential current pulse into different sensitive nodes of the three VCOs. In addition, SEE tests were conducted using pulsed laser experiments. Simulation and test results show that a CML VCO can effectively overcome the limitations presented by a RO-VCO and LC-tank VCO, achieving a wide range of tuning, and low sensitivity to noise and SEEs without the need for a large cross-section. Further studies of the proposed CML VCO were done on 28nm FDSOI in order to reduce the leakage current and increase the switching speed. the same current-starved VCO and CML VCO were implemented on this testchip, and simulations were performed by injecting a double exponential current pulse energy into the previously defined sensitive nodes. The results show SEE sensitivity improvement without narrowing the tuning range or affecting the phase noise response

An Energy-Efficient Reconfigurable Mobile Memory Interface for Computing Systems

The critical need for higher power efficiency and bandwidth transceiver design has significantly increased as mobile devices, such as smart phones, laptops, tablets, and ultra-portable personal digital assistants continue to be constructed using heterogeneous intellectual properties such as central processing units (CPUs), graphics processing units (GPUs), digital signal processors, dynamic random-access memories (DRAMs), sensors, and graphics/image processing units and to have enhanced graphic computing and video processing capabilities. However, the current mobile interface technologies which support CPU to memory communication (e.g. baseband-only signaling) have critical limitations, particularly super-linear energy consumption, limited bandwidth, and non-reconfigurable data access. As a consequence, there is a critical need to improve both energy efficiency and bandwidth for future mobile devices.;The primary goal of this study is to design an energy-efficient reconfigurable mobile memory interface for mobile computing systems in order to dramatically enhance the circuit and system bandwidth and power efficiency. The proposed energy efficient mobile memory interface which utilizes an advanced base-band (BB) signaling and a RF-band signaling is capable of simultaneous bi-directional communication and reconfigurable data access. It also increases power efficiency and bandwidth between mobile CPUs and memory subsystems on a single-ended shared transmission line. Moreover, due to multiple data communication on a single-ended shared transmission line, the number of transmission lines between mobile CPU and memories is considerably reduced, resulting in significant technological innovations, (e.g. more compact devices and low cost packaging to mobile communication interface) and establishing the principles and feasibility of technologies for future mobile system applications. The operation and performance of the proposed transceiver are analyzed and its circuit implementation is discussed in details. A chip prototype of the transceiver was implemented in a 65nm CMOS process technology. In the measurement, the transceiver exhibits higher aggregate data throughput and better energy efficiency compared to prior works

A Fully-Integrated Reconfigurable Dual-Band Transceiver for Short Range Wireless Communications in 180 nm CMOS

© 2015 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/ republishing this material for advertising or promotional purposes, creating new collective works for resale or redistribution to servers or lists, or reuse of any copyrighted components of this work in other works.A fully-integrated reconfigurable dual-band (760-960 MHz and 2.4-2.5 GHz) transceiver (TRX) for short range wireless communications is presented. The TRX consists of two individually-optimized RF front-ends for each band and one shared power-scalable analog baseband. The sub-GHz receiver has achieved the maximum 75 dBc 3rd-order harmonic rejection ratio (HRR3) by inserting a Q-enhanced notch filtering RF amplifier (RFA). In 2.4 GHz band, a single-ended-to-differential RFA with gain/phase imbalance compensation is proposed in the receiver. A ΣΔ fractional-N PLL frequency synthesizer with two switchable Class-C VCOs is employed to provide the LOs. Moreover, the integrated multi-mode PAs achieve the output P1dB (OP1dB) of 16.3 dBm and 14.1 dBm with both 25% PAE for sub-GHz and 2.4 GHz bands, respectively. A power-control loop is proposed to detect the input signal PAPR in real-time and flexibly reconfigure the PA's operation modes to enhance the back-off efficiency. With this proposed technique, the PAE of the sub-GHz PA is improved by x3.24 and x1.41 at 9 dB and 3 dB back-off powers, respectively, and the PAE of the 2.4 GHz PA is improved by x2.17 at 6 dB back-off power. The presented transceiver has achieved comparable or even better performance in terms of noise figure, HRR, OP1dB and power efficiency compared with the state-of-the-art.Peer reviewe

Ultra-Low-Power Wake-up Clock Design for SoC Applications

This thesis studies how to design an ultra-low-power wake-up clock circuit for SoCapplications that essentially consists of a resistor based reference circuit, switched-capacitor branch, an ultra-low-power amplifier, a VCO and a non-overlapping clockphase generator circuit. The circuit is designed in 180-nm CMOS technology usingCAD software for circuit design, layout design, pre and post-layout simulations.At first, a brief study of different clock-generation circuit architectures is made,wherein their merits and de-merits are discussed. This is followed by a study ofan ultra-low-power amplifier, ring-oscillator-based VCO, non-overlapping clockcircuits, the bias generation circuit and the current reference circuit. Additionally,a reference current chopping technique that further improves temperature stabilityis also described. Later, the report discusses the design and simulations of theactual implementation. Analysis of the design with regards to power consumption,temperature stability and layout area are carried out. The circuit operates at8.254kHz consuming 70.4nW with a temperature stability of 7.35ppm/◦C in thetemperature range of -40◦C to 75◦C. The final layout takes an area of 0.153mm2.The final design is analysed for its functionality at various process, voltage andtemperature corners. Future improvements in the current design are also discussedat the end of this report

Advanced CMOS Integrated Circuit Design and Application

The recent development of various application systems and platforms, such as 5G, B5G, 6G, and IoT, is based on the advancement of CMOS integrated circuit (IC) technology that enables them to implement high-performance chipsets. In addition to development in the traditional fields of analog and digital integrated circuits, the development of CMOS IC design and application in high-power and high-frequency operations, which was previously thought to be possible only with compound semiconductor technology, is a core technology that drives rapid industrial development. This book aims to highlight advances in all aspects of CMOS integrated circuit design and applications without discriminating between different operating frequencies, output powers, and the analog/digital domains. Specific topics in the book include: Next-generation CMOS circuit design and application; CMOS RF/microwave/millimeter-wave/terahertz-wave integrated circuits and systems; CMOS integrated circuits specially used for wireless or wired systems and applications such as converters, sensors, interfaces, frequency synthesizers/generators/rectifiers, and so on; Algorithm and signal-processing methods to improve the performance of CMOS circuits and systems

A Low-Voltage Mobility-Based Frequency Reference for Crystal-Less ULP Radios

The design of a 100 kHz frequency reference based on the electron mobility in a MOS transistor is presented. The proposed low-voltage low-power circuit requires no off-chip components, making it suitable for application in wireless sensor networks (WSN). After a single-point calibration, the spread of its output frequency is less than 1.1% (3 ) over the temperature range from -22 C to 85 C. Fabricated in a baseline 65 nm CMOS technology, the frequency reference circuit occupies 0.11 mm

Low power CMOS IC, biosensor and wireless power transfer techniques for wireless sensor network application

The emerging field of wireless sensor network (WSN) is receiving great attention due to the interest in healthcare. Traditional battery-powered devices suffer from large size, weight and secondary replacement surgery after the battery life-time which is often not desired, especially for an implantable application. Thus an energy harvesting method needs to be investigated. In addition to energy harvesting, the sensor network needs to be low power to extend the wireless power transfer distance and meet the regulation on RF power exposed to human tissue (specific absorption ratio). Also, miniature sensor integration is another challenge since most of the commercial sensors have rigid form or have a bulky size. The objective of this thesis is to provide solutions to the aforementioned challenges