216 research outputs found

    Experimental performance evaluation and design of schemes for passive RFID network

    Get PDF
    Passive Radio Frequency Identification (RFID) is a short range technology for transferring information. The main advantage of passive RFID systems over active communication systems is the battery-less operation at the client sides. However, there are two major challenges that limit the widespread adaptation of passive RFID systems: short communication range and low read rate in dense deployments. This dissertation addresses these issues by studying the root causes and develops solutions for them. In this dissertation, understanding the backscattering behavior of antennas and also the mutual coupling interactions among them are found to be the root causes of the two above-mentioned challenges for RFID networks. Thus, by studying these two main root causes solutions for them are proposed, investigated and verified, by simulations and measurements. The contributions in this dissertation include: (1) Design of a new measurement technique to estimate the structural scattering coefficient of a linear antenna. (2) Showing that the well-known Green model cannot completely explain the variation of the radar cross section of a T-match bowtie antenna over its Г plane. (3) Introducing dual loading in designing RFID antenna tags to: (a) Increase the vector differential backscattering signal, (b) Produce higher order modulations. (4) Introducing a new state for RFID tags in that tags switch to a low scattering states to: (a) suppress their interference to a target antenna in the network. (b) Stabilize the RCS of the target antenna. (c) Increase read rate in RFID networks. (5) Numeric analysis of the mutual coupling impedance for two side by side scattering antennas. (6) Introducing a multi-port RFID which can switch to different load impedances to help a target antenna in its vicinity increase its signal over the level when the target is alone in the field --Abstract, page iv

    Generic wireless sensor network for dynamic monitoring of a new generation of building material

    Get PDF
    Existing testing methods for building materials before deployment include a series of procedures as stipulated in British Standards, and most tests are performed in a controlled laboratory environment. Types of equipment used for measurements, data logging, and visualisation are commonly bulky, hard-wired, and consume a significant amount of power. Most of the off-the-shelf sensing nodes have been designed for a few specific applications and cannot be used for general purpose applications. This makes it difficult to modify or extend the sensing features when needed. This thesis takes the initiative of designing and implementing a low-powered, open-source, flexible, and small-sized Generic wireless sensor network (GWSN) that can continuously monitor the building materials and building environment, to address the limitations of the conventional measurement methods and the technological gap. The designed system is comprised of two custom-made sensor nodes and a gateway, as well as purpose designed firmware for data collection and processing. For the proof of concept and experimental studies, several measurement strategies were designed, to demonstrate, evaluate, and validate the effectiveness of the system. The data was collected from selected case study areas in the School of Energy, Geoscience, Infrastructure and Society (EGIS) laboratories by measuring and monitoring building structures and indoor environment quality parameters using the designed GWSN. The measured data includes heat flux through the material, surface and air temperatures on both sides of the material/structure, moisture variation, ambient temperature, relative humidity, carbon dioxide, volatile organic compounds, particulate matter, and sound/acoustic levels. The initial results show the potential of the designed system to become the new benchmark for tracking the variation of building materials with the environment and investigating the impact of variation of building materials on indoor environment quality. Based on the estimates of the thermal performance data, the sample used in the experiment had a typical U-value between 4.8 and 5.8 W/m2K and a thermal resistance value of 0.025m2 ·K/W[1][2]. Thermal resistance values from the GWSN real-time measurement were between 0.025 and 0.03 m2K/W, with an average of 0.025 m2K/W, and thermal transmission values varied between 4.55 and 5.11 W/m2K. Based on the data obtained, the results are within the range of typical values[3]. For thermal comfort measurements, the results of humidity and temperature from GWSN were compared to values in the Kambic climatic chamber in the EGIS laboratory, and the accuracies were 99 % and 98 % respectively. For the IAQ measurements, the values of CO2 and TVOCs were compared to the commercial off-the-shelf measuring system, and the accuracies were 98 %, and 97 %. Finally, the GWSN was tested for acoustic measurements in the range of 55 dB to 106 dB. The results were compared to class one Bruel & Kjaer SLM. The accuracy of GWSN was 97 %. The GWSN can be used for in lab and in-situ applications, to measure and analyse the thermal physical properties of building materials/building structures (thermal transmittance, thermal conductivity, and thermal resistance). The system can also measure indoor air quality, thermal comfort, and airborne sound insulation of the building envelope. The key point here is to establish a direct link between how building materials vary with the environment and how this impacts indoor environment quality. Such a link is essential for long-term analysis of building materials, which cannot be achieved using current methods. Regarding increasing the power efficient of the implemented GWSN as well as its performance and functionality, a new sensing platforms using backscatter technology have been introduced. The theory of modulation and spread spectrum technique used in backscattering has been explored. The trade-off between hardware complexity/power consumption and link performance has been investigated. Theoretical analysis and simulation validation of the new sensing technique, using backscatter communication, has been performed. A novel multicarrier backscatter tag compatible with Wireless Fidelity has been implemented and an IEEE 802.11g OFDM preamble was synthesized by simulation. The tag consists of only two transistors with current consumption no larger than 0.2 μA at voltage of less than 0.6 V. Novel harmonic suppression approaches for frequency-shifted backscatter communication has been proposed and demonstrated. The proposed approaches independently manipulate mirror harmonics and higher order harmonics whereby; specified higher order harmonics can be removed by carefully designing the real-valued (continuous and discrete) reflection coefficients-based backscatter tags. When successfully implemented, the backscatter system will reduce sensor node power consumption by shifting the power-consuming radio frequency carrier synthesis functions to carrier emitters.Engineering and Physical Sciences Research Council (EPSRC) Funding EP/H009612/

    Smart-antenna techniques for energy-efficient wireless sensor networks used in bridge structural health monitoring

    Get PDF
    Abstract: It is well known that wireless sensor networks differ from other computing platforms in that 1- they typically require a minimal amount of computing power at the nodes; 2- it is often desirable for sensor nodes to have drastically low power consumption. The main benefit of the this work is a substantial network life before batteries need to be replaced or, alternatively, the capacity to function off of modest environmental energy sources (energy harvesting). In the context of Structural Health Monitoring (SHM), battery replacement is particularly problematic since nodes can be in difficult to access locations. Furthermore, any intervention on a bridge may disrupt normal bridge operation, e.g. traffic may need to be halted. In this regard, switchbeam smart antennas in combination with wireless sensor networks (WSNs) have shown great potential in reducing implementation and maintenance costs of SHM systems. The main goal of implementing switch-beam smart antennas in our application is to reduce power consumption, by focusing the radiated energy only where it is needed. SHM systems capture the dynamic vibration information of a bridge structure in real-time in order to assess the health of the structure and to predict failures. Current SHM systems are based on piezoelectric patch sensors. In addition, the collection of data from the plurality of sensors distributed over the span of the bridge is typically performed through an expensive and bulky set of shielded wires which routes the information to a data sink at one end of the structure. The installation, maintenance and operational costs of such systems are extremely high due to high power consumption and the need for periodic maintenance. Wireless sensor networks represent an attractive alternative, in terms of cost, ease of maintenance, and power consumption. However, network lifetime in terms of node battery life must be very long (ideally 5–10 years) given the cost and hassle of manual intervention. In this context, the focus of this project is to reduce the global power consumption of the SHM system by implementing switched-beam smart antennas jointly with an optimized MAC layer. In the first part of the thesis, a sensor network platform for bridge SHM incorporating switched-beam antennas is modelled and simulated. where the main consideration is the joint optimization of beamforming parameters, MAC layer, and energy consumption. The simulation model, built within the Omnet++ network simulation framework, incorporates the energy consumption profiles of actual selected components (microcontroller, radio interface chip). The energy consumption and packet delivery ratio (PDR) of the network with switched-beam antennas is compared with an equivalent network based on omnidirectional antennas. In the second part of the thesis, this system model is leveraged to examine two distinct but interrelated aspects: Gallium Arsenide (GaAs) based solar energy harvesting and switched-beam antenna strategies. The main consideration here is the joint optimization of solar energy harvesting and switchedbeam directional antennas, where an equivalent network based on omnidirectional antennas acts as a baseline reference for comparison purposes.Il est bien connu que les réseaux de capteurs sans fils diffèrent des autres plateformes informatiques étant donné 1- qu’ils requièrent typiquement une puissance de calcul minimale aux noeuds du réseau ; 2- qu’il est souvent désirable que les noeuds capteurs aient une consommation d’énergie dramatiquement faible. La principale retombée de ce travail réside en la durée de vie allongée du réseau avant que les piles ne doivent être remplacées ou, alternativement, la capacité de fonctionner indéfiniment à partir de modestes sources d’énergie ambiente (glânage d’énergie). Dans le contexte du contrôle de la santé structurale (CSS), le remplacement de piles est particulièrement problématique puisque les noeuds peuvent se trouver en des endroits difficiles d’accès. De plus, toute intervention sur un pont implique une perturbation de l’opération normale de la structure, par exemple un arrêt du traffic. Dans ce contexte, les antennes intelligentes à commutation de faisceau en combinaison avec les réseaux de capteurs sans fils ont démontré un grand potentiel pour réduire les coûts de réalisation et d’entretien de systèmes de CSS. L’objectif principal de l’intégration d’antennes à commutation de faisceau dans notre application réside dans la réduction de la consommation énergétique, réalisée en concentrant l’énergie radiée uniquement là où elle est nécessaire. Les systèmes de CSS capturent l’information dynamique de vibration d’une structure de pont en temps réel de manière à évaluer la santé de la structure et prédire les failles. Les systèmes courants de CSS sont basés sur des senseurs piézoélectriques planaires. De plus, la collecte de données à partir de la pluralité de senseurs distribués sur l’étendue du pont est typiquement effectuée par le biais d’un ensemble coûteux et encombrant de câbles blindés qui véhiculent l’information jusqu’à un point de collecte à une extremité de la structure. L’installation, l’entretien, et les coûts opérationnels de tels systèmes sont extrêmement élevés étant donné la consommation de puissance élevée et le besoin d’entretien régulier. Les réseaux de capteurs sans fils représentent une alternative attrayante, en termes de coût, facilité d’entretien et consommation énergétique. Toutefois, la vie de réseau en termes de la durée de vie des piles doit être très longue (idéalement de 5 à 10 ans) étant donné le coût et les problèmes liés à l’intervention manuelle. Dans ce contexte, ce projet se concentre sur la réduction de la consommation de puissance globale d’un système de CSS en y intégrant des antennes intelligentes à commutation de faisceau conjointement avec une couche d’accès au médium (couche MAC) optimisée. Dans la première partie de la thèse, une plateforme de réseau de capteurs sans fils pour le CSS d’un pont incorporant des antennes à commutation de faisceaux est modélisé et simulé, avec pour considération principale l’optimisation des paramètres de sélection de faisceau, de la couche MAC et de la consommation d’énergie. Le modèle de simulation, construit dans le logiciel de simulation de réseaux Omnet++, incorpore les profils de consommation d’énergie de composants réels sélectionnés (microcontrôleur, puce d’interface radio). La consommation d’énergie et le taux de livraison de paquets du réseau avec antennes à commutation de faisceau est comparé avec un réseau équivalent basé sur des antennes omnidirectionnelles. Dans la deuxième partie de la thèse, le modèle système proposé est mis à contribution pour examiner deux aspects distrincts mais interreliés : le glânage d’énergie à partir de cellules solaire à base d’arséniure de Gallium (GaAs) et les stratégies liées aux antennes à commutation de faisceau. La considération principale ici est l’optimisation conjointe du glânage d’énergie et des antennes à commutation de faisceau, en ayant pour base de comparaison un réseau équivalent à base d’antennes omnidirectionnelles

    1-D broadside-radiating leaky-wave antenna based on a numerically synthesized impedance surface

    Get PDF
    A newly-developed deterministic numerical technique for the automated design of metasurface antennas is applied here for the first time to the design of a 1-D printed Leaky-Wave Antenna (LWA) for broadside radiation. The surface impedance synthesis process does not require any a priori knowledge on the impedance pattern, and starts from a mask constraint on the desired far-field and practical bounds on the unit cell impedance values. The designed reactance surface for broadside radiation exhibits a non conventional patterning; this highlights the merit of using an automated design process for a design well known to be challenging for analytical methods. The antenna is physically implemented with an array of metal strips with varying gap widths and simulation results show very good agreement with the predicted performance

    Beam scanning by liquid-crystal biasing in a modified SIW structure

    Get PDF
    A fixed-frequency beam-scanning 1D antenna based on Liquid Crystals (LCs) is designed for application in 2D scanning with lateral alignment. The 2D array environment imposes full decoupling of adjacent 1D antennas, which often conflicts with the LC requirement of DC biasing: the proposed design accommodates both. The LC medium is placed inside a Substrate Integrated Waveguide (SIW) modified to work as a Groove Gap Waveguide, with radiating slots etched on the upper broad wall, that radiates as a Leaky-Wave Antenna (LWA). This allows effective application of the DC bias voltage needed for tuning the LCs. At the same time, the RF field remains laterally confined, enabling the possibility to lay several antennas in parallel and achieve 2D beam scanning. The design is validated by simulation employing the actual properties of a commercial LC medium

    Development of sensors and non-destructive techniques to determine the performance of coatings in construction

    Get PDF
    The primary objective of this work was to examine and develop techniques for monitoring the degradation of Organically Coated Steel (OCS) in-situ. This included the detection of changes associated with the weathering to both the organic coating and metallic substrate. Initially, a review of current promising techniques was carried out however many were found to be unsuitable for this application and the adaptation of current techniques and the development of new techniques was considered. A brief concept investigation, based on initial testing and considerations, was used to determine a number of sensing techniques to examine. These included embedded, Resonant Frequency Identification (RFID), Magnetic Flux Leakage (MFL) and dielectric sensing. Each of these techniques were assessed for the application, prototyped, and tested against a range of samples to determine the accuracy and sensitivity of degradation detection provided. A range of poorly and highly durable coated samples were used in conjunction with accelerated weathering testing for this aim. Track based electronic printed sensors were presented as both a cut edge corrosion tracking and coating capacitance measurement method. While suffering somewhat from electrical paint compatibility issues both concepts showed merit in initial trials however the capacitive sensor ultimately proved insufficiently responsive to coating changes. The embedded, progressive failure-based, cut edge corrosion sensor was produced and tested in modern coating systems with moderate success. Novel applications of RFID and MLF techniques were considered and proved capable of detecting large changes in substrate condition due to significant corrosion. However, there was a lack of sufficient sensitivity when considering early-stage corrosion of durable modern OCS products. Finally, it was shown that a chipless antenna could be designed and optimised for novelly monitoring the changes to the dielectric properties of a paint layer due to degradation. However, ultimately this test, due to equipment requirements, lent itself more to lab testing than in-situ. Due to some of these limitations a different approach was considered in which the environmental factors influencing degradation were examined with the aim of relating these to performance across a building. It was observed that a combination of high humidity and the build-up of aggressive natural deposits contributed to high degradation rates in sheltered regions, such as building eaves, where microclimates were created. The build-up of deposits and their effect was presented as a key degradation accelerant during in-use service. A unique numerical simulation approach was developed to predict the natural washing, via rain impact and characteristics of the building analysed. This approach showed promise for determining areas unlikely to be naturally washed, and therefore subjected to a degradation accelerating, build-up of deposits. Given these understandings coated wetness sensors were considered as a realistic live-monitoring device capable of determining deposit build up and ultimately OCS lifetime

    Antenas setoriais para sistemas de localização em redes de sensores sem fios

    Get PDF
    Doutoramento em Engenharia EletrotécnicaThis work investigates low cost localization systems (LS) based on received signal strength (RSS) and integrated with different types of antennas with main emphasis on sectorial antennas. The last few years have witnessed an outstanding growth in wireless sensor networks (WSN). Among its various possible applications, the localization field became a major area of research. The localization techniques based on RSS are characterized by simplicity and low cost of integration. The integration of LS based on RSS and sectorial antennas (SA) was proven to provide an effective solution for reducing the number of required nodes of the networks and allows the combination of several techniques, such as RSS and angle of arrival (AoA). This PhD thesis focuses on studying techniques, antennas and protocols that best meet the needs of each LS with main focus on low cost systems based on RSS and AoA. Firstly there are studied localization techniques and system that best suit the requirements of the user and the antennas that are most appropriate according to the nature of the signal. In this step it is intended to provide a fundamental understanding of the undertaken work. Then the developed antennas are presented according to the following categories: sectorial and microstrip antennas. Two sectorial antennas are presented: a narrowband antenna operating at 2.4 to 2.5 GHz and a broadband antenna operating at 800MHz-2.4GHz. The low cost printed antennas were designed to operate at 5 GHz, which may be used for vehicular communication. After presenting the various antennas, several prototypes of indoor/outdoor LS are implemented and analyzed. Localization protocols are also proposed, one based on simplicity and low power, and the other on interoperability with different types of antennas and system requirements.O presente trabalho investiga sistemas de localização (SL) de baixo custo baseados na intensidade do sinal (RSS) e integrados com diferentes tipos de antenas com principal destaque para antenas sectoriais. Os últimos anos testemunharam um crescimento surpreendente de redes de sensores sem fios (RSSF), onde entre diversas aplicações possíveis, a localização tornou-se uma das principais áreas de pesquisa. Técnicas baseadas na intensidade do sinal caracterizam-se pela simplicidade e baixo custo de integração. A integração de SL baseados na intensidade do sinal recebido e antenas sectoriais (AS) oferecem uma solução eficaz para reduzir o número de nós necessários e para combinar diversas técnicas de localização. Esta tese de doutoramento foca-se no estudado de técnicas, antenas e protocolos de acordo com os requisitos de cada sistema localização com especial atenção para sistemas de baixo custo baseados na intensidade do sinal e no ângulo de chegada. Inicialmente são estudadas técnicas e SL de acordo com as necessidades do utilizador e as antenas que melhor se enquadram de acordo com a natureza do sinal. Esta etapa tem como objectivo proporcionar a compreensão fundamental do trabalho desenvolvido. Em seguida são apresentadas as antenas desenvolvidas divididas em: antenas sectorias e antenas impressas de baixo custo. Duas antenas sectoriais são apresentadas: uma de banda estreita a operar a 2,4-2,5GHz e outro de banda larga 800MHz-2.4GHz. As antenas impressas foram desenvolvidas para operar a 5 GHz, pelo que podem ser utilizadas para comunicação veicular. Após apresentação das diversas antenas vários protótipos de SL interiores/exteriores são implementados e analisados. Protocolos de localização são também propostos, um baseado na simplicidade e baixo consumo, outro na interoperabilidade com diferentes tipos de antenas e requisitos do sistema

    Low-Power Wide-Area Networks: A Broad Overview of its Different Aspects

    Get PDF
    Low-power wide-area networks (LPWANs) are gaining popularity in the research community due to their low power consumption, low cost, and wide geographical coverage. LPWAN technologies complement and outperform short-range and traditional cellular wireless technologies in a variety of applications, including smart city development, machine-to-machine (M2M) communications, healthcare, intelligent transportation, industrial applications, climate-smart agriculture, and asset tracking. This review paper discusses the design objectives and the methodologies used by LPWAN to provide extensive coverage for low-power devices. We also explore how the presented LPWAN architecture employs various topologies such as star and mesh. We examine many current and emerging LPWAN technologies, as well as their system architectures and standards, and evaluate their ability to meet each design objective. In addition, the possible coexistence of LPWAN with other technologies, combining the best attributes to provide an optimum solution is also explored and reported in the current overview. Following that, a comparison of various LPWAN technologies is performed and their market opportunities are also investigated. Furthermore, an analysis of various LPWAN use cases is performed, highlighting their benefits and drawbacks. This aids in the selection of the best LPWAN technology for various applications. Before concluding the work, the open research issues, and challenges in designing LPWAN are presented.publishedVersio

    A robust 2.4 GHz time-of-arrival based ranging system with sub-meter accuracy: feasibility study and realization of low power CMOS receiver

    Get PDF
    Draadloze sensornetwerken worden meer en meer aangewend om verschillende soorten informatie te verzamelen. De locatie, waar deze informatie verzameld is, is een belangerijke eigenschap en voor sommige toepassingen, zoals het volgen van personen of goederen, zelfs de meest belangrijke en mogelijkmakende factor. Om de positie van een sensor te bepalen, is een technologie nodig die de afstand tot een gekend referentiepunt schat. Door verschillende afstandsmetingen te combineren, is het mogelijk de absolute locatie van de node te berekenen
    • …
    corecore