Clock Generator Circuits for Low-Power Heterogeneous Multiprocessor Systems-on-Chip

In this work concepts and circuits for local clock generation in low-power heterogeneous multiprocessor systems-on-chip (MPSoCs) are researched and developed. The targeted systems feature a globally asynchronous locally synchronous (GALS) clocking architecture and advanced power management functionality, as for example fine-grained ultra-fast dynamic voltage and frequency scaling (DVFS). To enable this functionality compact clock generators with low chip area, low power consumption, wide output frequency range and the capability for ultra-fast frequency changes are required. They are to be instantiated individually per core. For this purpose compact all digital phase-locked loop (ADPLL) frequency synthesizers are developed. The bang-bang ADPLL architecture is analyzed using a numerical system model and optimized for low jitter accumulation. A 65nm CMOS ADPLL is implemented, featuring a novel active current bias circuit which compensates the supply voltage and temperature sensitivity of the digitally controlled oscillator (DCO) for reduced digital tuning effort. Additionally, a 28nm ADPLL with a new ultra-fast lock-in scheme based on single-shot phase synchronization is proposed. The core clock is generated by an open-loop method using phase-switching between multi-phase DCO clocks at a fixed frequency. This allows instantaneous core frequency changes for ultra-fast DVFS without re-locking the closed loop ADPLL. The sensitivity of the open-loop clock generator with respect to phase mismatch is analyzed analytically and a compensation technique by cross-coupled inverter buffers is proposed. The clock generators show small area (0.0097mm2 (65nm), 0.00234mm2 (28nm)), low power consumption (2.7mW (65nm), 0.64mW (28nm)) and they provide core clock frequencies from 83MHz to 666MHz which can be changed instantaneously. The jitter performance is compliant to DDR2/DDR3 memory interface specifications. Additionally, high-speed clocks for novel serial on-chip data transceivers are generated. The ADPLL circuits have been verified successfully by 3 testchip implementations. They enable efficient realization of future low-power MPSoCs with advanced power management functionality in deep-submicron CMOS technologies.In dieser Arbeit werden Konzepte und Schaltungen zur lokalen Takterzeugung in heterogenen Multiprozessorsystemen (MPSoCs) mit geringer Verlustleistung erforscht und entwickelt. Diese Systeme besitzen eine global-asynchrone lokal-synchrone Architektur sowie Funktionalität zum Power Management, wie z.B. das feingranulare, schnelle Skalieren von Spannung und Taktfrequenz (DVFS). Um diese Funktionalität zu realisieren werden kompakte Taktgeneratoren benötigt, welche eine kleine Chipfläche einnehmen, wenig Verlustleitung aufnehmen, einen weiten Bereich an Ausgangsfrequenzen erzeugen und diese sehr schnell ändern können. Sie sollen individuell pro Prozessorkern integriert werden. Dazu werden kompakte volldigitale Phasenregelkreise (ADPLLs) entwickelt, wobei eine bang-bang ADPLL Architektur numerisch modelliert und für kleine Jitterakkumulation optimiert wird. Es wird eine 65nm CMOS ADPLL implementiert, welche eine neuartige Kompensationsschlatung für den digital gesteuerten Oszillator (DCO) zur Verringerung der Sensitivität bezüglich Versorgungsspannung und Temperatur beinhaltet. Zusätzlich wird eine 28nm CMOS ADPLL mit einer neuen Technik zum schnellen Einschwingen unter Nutzung eines Phasensynchronisierers realisiert. Der Prozessortakt wird durch ein neuartiges Phasenmultiplex- und Frequenzteilerverfahren erzeugt, welches es ermöglicht die Taktfrequenz sofort zu ändern um schnelles DVFS zu realisieren. Die Sensitivität dieses Frequenzgenerators bezüglich Phasen-Mismatch wird theoretisch analysiert und durch Verwendung von kreuzgekoppelten Taktverstärkern kompensiert. Die hier entwickelten Taktgeneratoren haben eine kleine Chipfläche (0.0097mm2 (65nm), 0.00234mm2 (28nm)) und Leistungsaufnahme (2.7mW (65nm), 0.64mW (28nm)). Sie stellen Frequenzen von 83MHz bis 666MHz bereit, welche sofort geändert werden können. Die Schaltungen erfüllen die Jitterspezifikationen von DDR2/DDR3 Speicherinterfaces. Zusätzliche können schnelle Takte für neuartige serielle on-Chip Verbindungen erzeugt werden. Die ADPLL Schaltungen wurden erfolgreich in 3 Testchips erprobt. Sie ermöglichen die effiziente Realisierung von zukünftigen MPSoCs mit Power Management in modernsten CMOS Technologien

Proceedings of the 5th International Workshop on Reconfigurable Communication-centric Systems on Chip 2010 - ReCoSoC\u2710 - May 17-19, 2010 Karlsruhe, Germany. (KIT Scientific Reports ; 7551)

ReCoSoC is intended to be a periodic annual meeting to expose and discuss gathered expertise as well as state of the art research around SoC related topics through plenary invited papers and posters. The workshop aims to provide a prospective view of tomorrow\u27s challenges in the multibillion transistor era, taking into account the emerging techniques and architectures exploring the synergy between flexible on-chip communication and system reconfigurability

SdrLift: A Domain-Specific Intermediate Hardware Synthesis Framework for Prototyping Software-Defined Radios

Modern design of Software-Defined Radio (SDR) applications is based on Field Programmable Gate Arrays (FPGA) due to their ability to be configured into solution architectures that are well suited to domain-specific problems while achieving the best trade-off between performance, power, area, and flexibility. FPGAs are well known for rich computational resources, which traditionally include logic, register, and routing resources. The increased technological advances have seen FPGAs incorporating more complex components that comprise sophisticated memory blocks, Digital Signal Processing (DSP) blocks, and high-speed interfacing to Gigabit Ethernet (GbE) and Peripheral Component Interconnect Express (PCIe) bus. Gateware for programming FPGAs is described at a lowlevel of design abstraction using Register Transfer Language (RTL), typically using either VHSIC-HDL (VHDL) or Verilog code. In practice, the low-level description languages have a very steep learning curve, provide low productivity for hardware designers and lack readily available open-source library support for fundamental designs, and consequently limit the design to only hardware experts. These limitations have led to the adoption of High-Level Synthesis (HLS) tools that raise design abstraction using syntax, semantics, and software development notations that are well-known to most software developers. However, while HLS has made programming of FPGAs more accessible and can increase the productivity of design, they are still not widely adopted in the design community due to the low-level skills that are still required to produce efficient designs. Additionally, the resultant RTL code from HLS tools is often difficult to decipher, modify and optimize due to the functionality and micro-architecture that are coupled together in a single High-Level Language (HLL). In order to alleviate these problems, Domain-Specific Languages (DSL) have been introduced to capture algorithms at a high level of abstraction with more expressive power and providing domain-specific optimizations that factor in new transformations and the trade-off between resource utilization and system performance. The problem of existing DSLs is that they are designed around imperative languages with an instruction sequence that does not match the hardware structure and intrinsics, leading to hardware designs with system properties that are unconformable to the high-level specifications and constraints. The aim of this thesis is, therefore, to design and implement an intermediatelevel framework namely SdrLift for use in high-level rapid prototyping of SDR applications that are based on an FPGA. The SdrLift input is a HLL developed using functional language constructs and design patterns that specify the structural behavior of the application design. The functionality of the SdrLift language is two-fold, first, it can be used directly by a designer to develop the SDR applications, secondly, it can be used as the Intermediate Representation (IR) step that is generated by a higher-level language or a DSL. The SdrLift compiler uses the dataflow graph as an IR to structurally represent the accelerator micro-architecture in which the components correspond to the fine-level and coarse-level Hardware blocks (HW Block) which are either auto-synthesized or integrated from existing reusable Intellectual Property (IP) core libraries. Another IR is in the form of a dataflow model and it is used for composition and global interconnection of the HW Blocks while making efficient interfacing decisions in an attempt to satisfy speed and resource usage objectives. Moreover, the dataflow model provides rules and properties that will be used to provide a theoretical framework that formally analyzes the characteristics of SDR applications (i.e. the throughput, sample rate, latency, and buffer size among other factors). Using both the directed graph flow (DFG) and the dataflow model in the SdrLift compiler provides two benefits: an abstraction of the microarchitecture from the high-level algorithm specifications and also decoupling of the microarchitecture from the low-level RTL implementation. Following the IR creation and model analyses is the VHDL code generation which employs the low-level optimizations that ensure optimal hardware design results. The code generation process per forms analysis to ensure the resultant hardware system conforms to the high-level design specifications and constraints. SdrLift is evaluated by developing representative SDR case studies, in which the VHDL code for eight different SDR applications is generated. The experimental results show that SdrLift achieves the desired performance and flexibility, while also conserving the hardware resources utilized

Energy-Sustainable IoT Connectivity: Vision, Technological Enablers, Challenges, and Future Directions

Technology solutions must effectively balance economic growth, social equity, and environmental integrity to achieve a sustainable society. Notably, although the Internet of Things (IoT) paradigm constitutes a key sustainability enabler, critical issues such as the increasing maintenance operations, energy consumption, and manufacturing/disposal of IoT devices have long-term negative economic, societal, and environmental impacts and must be efficiently addressed. This calls for self-sustainable IoT ecosystems requiring minimal external resources and intervention, effectively utilizing renewable energy sources, and recycling materials whenever possible, thus encompassing energy sustainability. In this work, we focus on energy-sustainable IoT during the operation phase, although our discussions sometimes extend to other sustainability aspects and IoT lifecycle phases. Specifically, we provide a fresh look at energy-sustainable IoT and identify energy provision, transfer, and energy efficiency as the three main energy-related processes whose harmonious coexistence pushes toward realizing self-sustainable IoT systems. Their main related technologies, recent advances, challenges, and research directions are also discussed. Moreover, we overview relevant performance metrics to assess the energy-sustainability potential of a certain technique, technology, device, or network and list some target values for the next generation of wireless systems. Overall, this paper offers insights that are valuable for advancing sustainability goals for present and future generations.Comment: 25 figures, 12 tables, submitted to IEEE Open Journal of the Communications Societ

Temperature, energy and performance: addressing embedded system challenges through fast cache simulation

Temperature, energy and performance are essential design considerations during the conception of modern digital systems. The work presented in this thesis focusses on three aspects that can be used to overcome these limitations. First an evaluation of the suitability of the dynamic application adaptation method is researched with the aim of using it to control the temperature of a Field Programmable Gate Array (FPGA) device. Despite the use of an extremely adaptive custom JPEG encoder, it was determined that application adaptation alone is ineffective in an FPGA for thermal management. Next, a study is performed which aims to assess which components are principally responsible for the rise in temperatures in FPGAs. It was found that the external memory interface is a significant heat-source in FPGA-based embedded systems, and that device temperature correlates with CPU cache miss rate. The third and main aspect covered in this dissertation is the speeding up of CPU cache simulation. Single pass cache simulation is a tool that can be employed at design time to select a cache yielding acceptable temperature, system performance and energy consumption. Three Multiple cAche Simulators in Hardware (MASH) or in Software (MASS) are proposed for three cache replacement policies: MASH{lru} for the Least Recently Used (LRU) cache algorithm, MASH{fifo} for First In First Out (FIFO) and MASS{plrut} for Pseudo Least Recently Used tree (PLRUt). The former two are novel in that they are implemented in hardware and are respectively 53x and 11.10x faster than software counterparts. The PLRUt simulator presents for the first time an optimised hash table-based algorithm yielding a speedup of 1.93x over an unoptimised solution. All cache simulators employ cache properties specific to their replacement policies to improve simulator characteristics. Additionally, it is shown that the hardware (or MASH) simulators can be implemented in-system alongside an embedded system, allowing for the direct trace extraction and cache simulation from within an FPGA. Using in-system simulation, large speedups can be achieved as trace generation and multiple cache simulation happen at the same time at high frequencies

Survey of FPGA applications in the period 2000 – 2015 (Technical Report)

Romoth J, Porrmann M, Rückert U. Survey of FPGA applications in the period 2000 – 2015 (Technical Report).; 2017.Since their introduction, FPGAs can be seen in more and more different fields of applications. The key advantage is the combination of software-like flexibility with the performance otherwise common to hardware. Nevertheless, every application field introduces special requirements to the used computational architecture. This paper provides an overview of the different topics FPGAs have been used for in the last 15 years of research and why they have been chosen over other processing units like e.g. CPUs

Clock Generator Circuits for Low-Power Heterogeneous Multiprocessor Systems-on-Chip

In this work concepts and circuits for local clock generation in low-power heterogeneous multiprocessor systems-on-chip (MPSoCs) are researched and developed. The targeted systems feature a globally asynchronous locally synchronous (GALS) clocking architecture and advanced power management functionality, as for example fine-grained ultra-fast dynamic voltage and frequency scaling (DVFS). To enable this functionality compact clock generators with low chip area, low power consumption, wide output frequency range and the capability for ultra-fast frequency changes are required. They are to be instantiated individually per core. For this purpose compact all digital phase-locked loop (ADPLL) frequency synthesizers are developed. The bang-bang ADPLL architecture is analyzed using a numerical system model and optimized for low jitter accumulation. A 65nm CMOS ADPLL is implemented, featuring a novel active current bias circuit which compensates the supply voltage and temperature sensitivity of the digitally controlled oscillator (DCO) for reduced digital tuning effort. Additionally, a 28nm ADPLL with a new ultra-fast lock-in scheme based on single-shot phase synchronization is proposed. The core clock is generated by an open-loop method using phase-switching between multi-phase DCO clocks at a fixed frequency. This allows instantaneous core frequency changes for ultra-fast DVFS without re-locking the closed loop ADPLL. The sensitivity of the open-loop clock generator with respect to phase mismatch is analyzed analytically and a compensation technique by cross-coupled inverter buffers is proposed. The clock generators show small area (0.0097mm2 (65nm), 0.00234mm2 (28nm)), low power consumption (2.7mW (65nm), 0.64mW (28nm)) and they provide core clock frequencies from 83MHz to 666MHz which can be changed instantaneously. The jitter performance is compliant to DDR2/DDR3 memory interface specifications. Additionally, high-speed clocks for novel serial on-chip data transceivers are generated. The ADPLL circuits have been verified successfully by 3 testchip implementations. They enable efficient realization of future low-power MPSoCs with advanced power management functionality in deep-submicron CMOS technologies.In dieser Arbeit werden Konzepte und Schaltungen zur lokalen Takterzeugung in heterogenen Multiprozessorsystemen (MPSoCs) mit geringer Verlustleistung erforscht und entwickelt. Diese Systeme besitzen eine global-asynchrone lokal-synchrone Architektur sowie Funktionalität zum Power Management, wie z.B. das feingranulare, schnelle Skalieren von Spannung und Taktfrequenz (DVFS). Um diese Funktionalität zu realisieren werden kompakte Taktgeneratoren benötigt, welche eine kleine Chipfläche einnehmen, wenig Verlustleitung aufnehmen, einen weiten Bereich an Ausgangsfrequenzen erzeugen und diese sehr schnell ändern können. Sie sollen individuell pro Prozessorkern integriert werden. Dazu werden kompakte volldigitale Phasenregelkreise (ADPLLs) entwickelt, wobei eine bang-bang ADPLL Architektur numerisch modelliert und für kleine Jitterakkumulation optimiert wird. Es wird eine 65nm CMOS ADPLL implementiert, welche eine neuartige Kompensationsschlatung für den digital gesteuerten Oszillator (DCO) zur Verringerung der Sensitivität bezüglich Versorgungsspannung und Temperatur beinhaltet. Zusätzlich wird eine 28nm CMOS ADPLL mit einer neuen Technik zum schnellen Einschwingen unter Nutzung eines Phasensynchronisierers realisiert. Der Prozessortakt wird durch ein neuartiges Phasenmultiplex- und Frequenzteilerverfahren erzeugt, welches es ermöglicht die Taktfrequenz sofort zu ändern um schnelles DVFS zu realisieren. Die Sensitivität dieses Frequenzgenerators bezüglich Phasen-Mismatch wird theoretisch analysiert und durch Verwendung von kreuzgekoppelten Taktverstärkern kompensiert. Die hier entwickelten Taktgeneratoren haben eine kleine Chipfläche (0.0097mm2 (65nm), 0.00234mm2 (28nm)) und Leistungsaufnahme (2.7mW (65nm), 0.64mW (28nm)). Sie stellen Frequenzen von 83MHz bis 666MHz bereit, welche sofort geändert werden können. Die Schaltungen erfüllen die Jitterspezifikationen von DDR2/DDR3 Speicherinterfaces. Zusätzliche können schnelle Takte für neuartige serielle on-Chip Verbindungen erzeugt werden. Die ADPLL Schaltungen wurden erfolgreich in 3 Testchips erprobt. Sie ermöglichen die effiziente Realisierung von zukünftigen MPSoCs mit Power Management in modernsten CMOS Technologien

Clock Generator Circuits for Low-Power Heterogeneous Multiprocessor Systems-on-Chip

In this work concepts and circuits for local clock generation in low-power heterogeneous multiprocessor systems-on-chip (MPSoCs) are researched and developed. The targeted systems feature a globally asynchronous locally synchronous (GALS) clocking architecture and advanced power management functionality, as for example fine-grained ultra-fast dynamic voltage and frequency scaling (DVFS). To enable this functionality compact clock generators with low chip area, low power consumption, wide output frequency range and the capability for ultra-fast frequency changes are required. They are to be instantiated individually per core. For this purpose compact all digital phase-locked loop (ADPLL) frequency synthesizers are developed. The bang-bang ADPLL architecture is analyzed using a numerical system model and optimized for low jitter accumulation. A 65nm CMOS ADPLL is implemented, featuring a novel active current bias circuit which compensates the supply voltage and temperature sensitivity of the digitally controlled oscillator (DCO) for reduced digital tuning effort. Additionally, a 28nm ADPLL with a new ultra-fast lock-in scheme based on single-shot phase synchronization is proposed. The core clock is generated by an open-loop method using phase-switching between multi-phase DCO clocks at a fixed frequency. This allows instantaneous core frequency changes for ultra-fast DVFS without re-locking the closed loop ADPLL. The sensitivity of the open-loop clock generator with respect to phase mismatch is analyzed analytically and a compensation technique by cross-coupled inverter buffers is proposed. The clock generators show small area (0.0097mm2 (65nm), 0.00234mm2 (28nm)), low power consumption (2.7mW (65nm), 0.64mW (28nm)) and they provide core clock frequencies from 83MHz to 666MHz which can be changed instantaneously. The jitter performance is compliant to DDR2/DDR3 memory interface specifications. Additionally, high-speed clocks for novel serial on-chip data transceivers are generated. The ADPLL circuits have been verified successfully by 3 testchip implementations. They enable efficient realization of future low-power MPSoCs with advanced power management functionality in deep-submicron CMOS technologies.In dieser Arbeit werden Konzepte und Schaltungen zur lokalen Takterzeugung in heterogenen Multiprozessorsystemen (MPSoCs) mit geringer Verlustleistung erforscht und entwickelt. Diese Systeme besitzen eine global-asynchrone lokal-synchrone Architektur sowie Funktionalität zum Power Management, wie z.B. das feingranulare, schnelle Skalieren von Spannung und Taktfrequenz (DVFS). Um diese Funktionalität zu realisieren werden kompakte Taktgeneratoren benötigt, welche eine kleine Chipfläche einnehmen, wenig Verlustleitung aufnehmen, einen weiten Bereich an Ausgangsfrequenzen erzeugen und diese sehr schnell ändern können. Sie sollen individuell pro Prozessorkern integriert werden. Dazu werden kompakte volldigitale Phasenregelkreise (ADPLLs) entwickelt, wobei eine bang-bang ADPLL Architektur numerisch modelliert und für kleine Jitterakkumulation optimiert wird. Es wird eine 65nm CMOS ADPLL implementiert, welche eine neuartige Kompensationsschlatung für den digital gesteuerten Oszillator (DCO) zur Verringerung der Sensitivität bezüglich Versorgungsspannung und Temperatur beinhaltet. Zusätzlich wird eine 28nm CMOS ADPLL mit einer neuen Technik zum schnellen Einschwingen unter Nutzung eines Phasensynchronisierers realisiert. Der Prozessortakt wird durch ein neuartiges Phasenmultiplex- und Frequenzteilerverfahren erzeugt, welches es ermöglicht die Taktfrequenz sofort zu ändern um schnelles DVFS zu realisieren. Die Sensitivität dieses Frequenzgenerators bezüglich Phasen-Mismatch wird theoretisch analysiert und durch Verwendung von kreuzgekoppelten Taktverstärkern kompensiert. Die hier entwickelten Taktgeneratoren haben eine kleine Chipfläche (0.0097mm2 (65nm), 0.00234mm2 (28nm)) und Leistungsaufnahme (2.7mW (65nm), 0.64mW (28nm)). Sie stellen Frequenzen von 83MHz bis 666MHz bereit, welche sofort geändert werden können. Die Schaltungen erfüllen die Jitterspezifikationen von DDR2/DDR3 Speicherinterfaces. Zusätzliche können schnelle Takte für neuartige serielle on-Chip Verbindungen erzeugt werden. Die ADPLL Schaltungen wurden erfolgreich in 3 Testchips erprobt. Sie ermöglichen die effiziente Realisierung von zukünftigen MPSoCs mit Power Management in modernsten CMOS Technologien