Parametric analog signal amplification applied to nanoscale cmos wireless digital transceivers

Thesis presented in partial fulfillment of the requirements for the degree of Doctor of Philosophy in the subject of Electrical and Computer Engineering by the Universidade Nova de Lisboa,Faculdade de Ciências e TecnologiaSignal amplification is required in almost every analog electronic system. However noise is also present, thus imposing limits to the overall circuit performance, e.g., on the sensitivity of the radio transceiver. This drawback has triggered a major research on the field, which has been producing several solutions to achieve amplification with minimum added noise. During the Fifties, an interesting out of mainstream path was followed which was based on variable reactance instead of resistance based amplifiers. The principle of these parametric circuits permits to achieve low noise amplifiers since the controlled variations of pure reactance elements is intrinsically noiseless. The amplification is based on a mixing effect which enables energy transfer from an AC pump source to other related signal frequencies. While the first implementations of these type of amplifiers were already available at that time, the discrete-time version only became visible more recently. This discrete-time version is a promising technique since it is well adapted to the mainstream nanoscale CMOS technology. The technique itself is based on the principle of changing the surface potential of the MOS device while maintaining the transistor gate in a floating state. In order words, the voltage amplification is achieved by changing the capacitance value while maintaining the total charge unchanged during an amplification phase. Since a parametric amplifier is not intrinsically dependent on the transconductance of the MOS transistor, it does not directly suffer from the intrinsic transconductance MOS gain issues verified in nanoscale MOS technologies. As a consequence, open-loop and opamp free structures can further emerge with this additional contribution. This thesis is dedicated to the analysis of parametric amplification with special emphasis on the MOS discrete-time implementation. The use of the latter is supported on the presentation of several circuits where the MOS Parametric Amplifier cell is well suited: small gain amplifier, comparator, discrete-time mixer and filter, and ADC. Relatively to the latter, a high speed time-interleaved pipeline ADC prototype is implemented in a,standard 130 nm CMOS digital technology from United Microelectronics Corporation (UMC). The ADC is fully based on parametric MOS amplification which means that one could achieve a compact and MOS-only implementation. Furthermore, any high speed opamp has not been used in the signal path, being all the amplification steps implemented with open-loop parametric MOS amplifiers. To the author’s knowledge, this is first reported pipeline ADC that extensively used the parametric amplification concept.Fundação para a Ciência e Tecnologia through the projects SPEED, LEADER and IMPAC

A 1.67 pJ/Conversion-step 8-bit SAR-Flash ADC Architecture in 90-nm CMOS Technology

A novice advanced architecture of 8-bit analog todigital converter is introduced and analyzed in this work. Thestructure of proposed ADC is based on the sub-ranging ADCarchitecture in which a 4-bit resolution flash-ADC is utilized. Theproposed ADC architecture is designed by employing a comparatorwhich is equipped with common mode current feedback andgain boosting technique (CMFD-GB) and a residue amplifier. Theproposed 8 bits ADC structure can achieve the speed of 140 megasamplesper second. The proposed ADC architecture is designedat a resolution of 8 bits at 10 MHz sampling frequency. DNL andINL values of the proposed design are -0.94/1.22 and -1.19/1.19respectively. The ADC design dissipates a power of 1.24 mWwith the conversion speed of 0.98 ns. The magnitude of SFDRand SNR from the simulations at Nyquist input is 39.77 and 35.62decibel respectively. Simulations are performed on a SPICE basedtool in 90 nm CMOS technology. The comparison shows betterperformance for the proposed ADC design in comparison toother ADC architectures regarding speed, resolution and powerconsumption

Power efficient analog-to-digital converters using both voltage and time domain information

As advanced wired and wireless communication systems attempt to achieve higher performance, the demand for high resolution and wide signal bandwidth in their associated ADCs is strongly increased. Recently, time-domain quantization has drawn attention from its scalability in deep submicron CMOS processes. Furthermore, there are several interesting aspects of time-domain quantizer by processing the signal in time rather than only in voltage domain especially for power efficiency. This research focuses on developing a new architecture for power efficient, high resolution ADCs using both voltage and time domain information. As a first approach, a new ΔƩ ADC based on a noise-shaped two-step integrating quantizer which quantizes the signal in voltage and time domains is presented. Attaining an extra order of noise-shaping from the integrating quantizer, the proposed ΔƩ ADC manifests a second-order noise-shaping with a first-order loop filter. Furthermore, this quantizer provides an 8b uantization in itself, drastically reducing the oversampling requirement. The proposed ADC also incorporates a new feedback DAC topology that alleviates the feedback DAC complexity of a two-step 8b quantizer. The measured results of the prototype ADC implemented in a 0.13μm CMOS demonstrate peak SNDR of 70.7dB (11.5b ENOB) at 8.1mW power, with an 8x OSR at 80MHz sampling frequency. To further improve ADC performance, a Nyquist ADC based on a time-based pipelined TDC is also proposed as a second approach. In this work, a simple V-T conversion scheme with a cheap low gain amplifier in its first stage and a hybrid time-domain quantization stage based on simple charge pump and capacitive DAC in its backend stages, are also proposed to improve ADC linearity and power efficiency. Using voltage and time domain information, the proposed ADC architecture is beneficial for both resolution and power efficiency, with MSBs resolved in voltage domain and LSBs in time domain. The measured results of the prototype ADC implemented in a 0.13μm CMOS demonstrate peak SNDR of 69.3dB (11.2b ENOB) at 6.38mW power and 70MHz sampling frequency. The FOM is 38.2fJ/conversion-step

Energy-efficient analog-to-digital conversion for ultra-wideband radio

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2007.Includes bibliographical references (p. 207-222).In energy constrained signal processing and communication systems, a focus on the analog or digital circuits in isolation cannot achieve the minimum power consumption. Furthermore, in advanced technologies with significant variation, yield is traditionally achieved only through conservative design and a sacrifice of energy efficiency. In this thesis, these limitations are addressed with both a comprehensive mixed-signal design methodology and new circuits and architectures, as presented in the context of an analog-to-digital converter (ADC) for ultra-wideband (UWB) radio. UWB is an emerging technology capable of high-data-rate wireless communication and precise locationing, and it requires high-speed (>500MS/s), low-resolution ADCs. The successive approximation register (SAR) topology exhibits significantly reduced complexity compared to the traditional flash architecture. Three time-interleaved SAR ADCs have been implemented. At the mixed-signal optimum energy point, parallelism and reduced voltage supplies provide more than 3x energy savings. Custom control logic, a new capacitive DAC, and a hierarchical sampling network enable the high-speed operation. Finally, only a small amount of redundancy, with negligible power penalty, dramatically improves the yield of the highly parallel ADC in deep sub-micron CMOS.by Brian P. Ginsburg.Ph.D

Circuits and algorithms for pipelined ADCs in scaled CMOS technologies

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2008.MIT Barker Engineering Library copy: printed in pages.Also issued printed in pages.Includes bibliographical references (leaves 179-184).CMOS technology scaling is creating significant issues for analog circuit design. For example, reduced signal swing and device gain make it increasingly difficult to realize high-speed, high-gain feedback loops traditionally used in switched capacitor circuits. This research involves two complementary methods for addressing scaling issues. First is the development of two blind digital calibration techniques. Decision Boundary Gap Estimation (DBGE) removes static non-linearities and Chopper Offset Estimation (COE) nulls offsets in pipelined ADCs. Second is the development of circuits for a new architecture called zero-crossing based circuits (ZCBC) that is more amenable to scaling trends. To demonstrate these circuits and algorithms, two different ADCs were designed: an 8 bit, 200MS/s in TSMC 180nm technology, and a 12 bit, 50 MS/s in IBM 90nm technology. Together these techniques can be enabling technologies for both pipelined ADCs and general mixed signal design in deep sub-micron technologies.by Lane Gearle Brooks.Ph.D