A Bidirectional Soft-Switched DAB-Based Single-Stage Three-Phase AC–DC Converter for V2G Application

In vehicle-to-grid applications, the battery charger of the electric vehicle (EV) needs to have a bidirectional power flow capability. Galvanic isolation is necessary for safety. An ac-dc bidirectional power converter with high-frequency isolation results in high power density, a key requirement for an on-board charger of an EV. Dual-active-bridge (DAB) converters are preferred in medium power and high voltage isolated dc-dc converters due to high power density and better efficiency. This paper presents a DAB-based three-phase ac-dc isolated converter with a novel modulation strategy that results in: 1) single-stage power conversion with no electrolytic capacitor, improving the reliability and power density; 2) open-loop power factor correction; 3) soft-switching of all semiconductor devices; and 4) a simple linear relationship between the control variable and the transferred active power. This paper presents a detailed analysis of the proposed operation, along with simulation results and experimental verification

Single-Phase Bi-directional Ćuk Inverter for Battery Applications

Bidirectional inverters are widely applied in photovoltaic and wind systems that require battery power backup. They are advantageous over unidirectional inverters because of their ability to convert DC power into AC power and then AC power back into DC power to recharge for storage purposes. Generally, bidirectional inverters are designed to have multiple power stages and/or make use of transformers for isolation and voltage/current gain. This usually increases the cost of production and oftentimes reduces the efficiency of the system. At the same time, attempts at eliminating usage of transformers and reduction in the number of power stages limits the range of bidirectional inverters’ capabilities. This is because battery applications today require low voltage DC-AC inverters with AC-DC power flow capability to store energy for later use. As such, only buck-boost based topologies are majorly being proposed and used for this functionality. The buck boost converter is the most widely used in such applications because of its higher efficiency, low component count and simple structure. It has drawbacks, however, such as: pulsating input and output currents - this leads to lower high electromagnetic interference; lower power factor during AC-DC power flow rectification when the batteries are being recharged; and external filter is also required during this power flow to keep the charging voltage constant. This research proposes a bidirectional inverter that attempts to overcome the drawbacks of the widely used buck-boost converter-based topology. The bidirectional inverter proposed in this work is based on a bidirectional Ćuk converter. The Ćuk converter has both continuous input and output currents. A galvanic isolation option on a Ćuk converter is simpler than a buck boost converter - this is important for grid tied systems. The inverter is based on a pseudo DC-link architecture - it uses a front end Ćuk converter cascaded with an unfolding bridge to convert DC power into AC power. The switches in the converter stage are switched at high frequency, while the switches in the unfolding stage are switched slower at the grid frequency. This configuration is desirable over the two-stage topologies because the switching losses in the unfolding bridge are lower because of this low switching frequency used. This configuration also ensures good switch utilization at the unfolding stage by lowering the parasitic effects on the power transfer. The proposed inverter has 4 modes of operation: during modes I and II the power is positive, and it converts DC power into AC power; during modes III and IV the power is negative, and it converts AC power back into DC power. The inverter is designed such that during DC-AC power flow, the input and output inductor currents and coupling capacitor voltage are continuous for improved efficiency. During the AC-DC power flow, the coupling capacitor voltage is discontinuous to achieve a higher input power factor by improving the AC line current, thereby simultaneously increasing the efficiency. The inverter was analysed in terms of: the dead time inserted into the switches to avoid shoot through and shortcircuiting switches; the parasitic effects on the power transfer ratio. Because the Cúk inverter is a high order system, several robust control strategies, such as sliding mode and current control have been proposed. These control methods require complex theory and present practical challenges to be reviewed. As such a new nested loop control strategy was proposed based on the dynamics of the coupling capacitor as the primary energy storage in the Cúk inverter. The control strategy uses 2 loops: an inner current loop and an outer voltage loop. Lead compensators were designed for both the current and voltage loops to achieve good dynamic response at a high bandwidth. Both simulated and experimental results showed that the bidirectional inverter was able to meet the design specifications. The control strategy showed good dynamic response and disturbance rejection under several inverter variations. Although the efficiency during simulations was above 96%, the experimental efficiency dropped significantly because the inverter was built on a Vero board for easy manipulation. The AC input power factor was > 0.95 for both simulated and experimental results

Centralized power control strategy for AC-DC hybrid micro-grid system using multi-converter scheme

In this paper, an ac-dc hybrid micro-grid system including a centralized power control scheme is proposed. Multiple ac-dc bidirectional converters connected in parallel are considered in the system instead of a single converter that connects ac and dc buses. The proposed control scheme is basically coordination of two modes-control of power through the converters and selection of converter units. The power through the converter is controlled because the load unbalance between ac and dc buses should be mitigated. Selection of converter units is also important because each small unit can deal partial amounts of power of the entire micro-grid system and therefore control of parallel operation of multiple converter units should be considered. If any converter fails to operate in the system then the alternate converters come into operation, so that the micro-grid system will not be totally disconnected and thus reliability of the system is ensured. This will also increase the efficiency of the system during low power transmission condition. The system operation is investigated under three different conditions to show the effectiveness of the proposed control scheme

Modelling, simulation and real time implementation of a three phase AC to AC matrix converter

Matrix converters (MCs) are essentially forced commutated cycloconverters with inherent four quadrant operation consisting of a matrix of bidirectional switches such that there is a switch for each possible connection between the input and output lines. Matrix converter directly converts the AC input voltage at any given frequency to AC output voltage with arbitrary amplitude at any unrestricted frequency without the need for a dc link capacitor storage element at the input side.The introduction of bidirectional switches using power transistors and IGBTs made easy realization of the matrix converter. The real development of the matrix converter starts with the work of Venturini and Alesina who proposed a mathematical analysis and introduced the Low-Frequency Modulation Matrix concept to describe the low frequency behavior of the matrix converter [1-3]. In this, the output voltages are obtained by multiplication of the modulation matrix or transfer matrix with the input voltages. One of the essential requirements for switching three phase AC to three phase AC MC is that two or more bidirectional switches connected to any one output phase should NOT be closed simultaneously, as this will cause dangerously high short circuit current. Similarly any one bidirectional switch connected to each output phase should remain closed to provide a current path with inductive load.This thesis mainly provides an account of the three phase AC to three phase AC MC modelling concept with SIMULINK software using fundamental Venturini and Optimum Venturini modulation algorithm [1-8], advanced modulation algorithm such as that proposed by Sunter-Clare [11-12] and by Ned Mohan [13-14, 16-17], application of these algorithms for the Vector control of three phase Induction Motor (IM) drive [15], real time hardware in the loop simulation [51,54-55] for a three phase AC to single phase AC MC, three phase AC to three phase AC Multilevel MC (MMC) with three [18-19] and six flying capacitors per output phase using PSCAD software (as SIMULINK started shooting trouble), Indirect (ISVM) [25-30] and Direct (DASVM, DSSVM, CZASVM) [31-38] Space Vector Modulation, newly discovered dual programmable AC to DC rectifier concept using three phase AC to three phase AC MC [43-45], Delta-Sigma Modulated MC [46-49] and single phase AC to three phase AC MC [50].In addition a novel concept of a single phase / three phase AC to single phase / three phase AC converter using a DC link, complementary N and P MOSFETs and IGBTs is presented. A chapter on model verification is also presented where selected SIMULINK models from various chapters have been verified by using either PSCAD or PSIM software. An appendix on PIC microcontroller PIC16F84A application to saw-tooth carrier waveform generation and switching three phase AC to three phase AC converters using a DC link is added. Another appendix on speed control and brake by plugging of three phase induction motor fed by matrix converter is presented. List of publications from this thesis is presented on third appendix

Bidirectional DC-DC Converter with High Voltage Gain for the Charge/Discharge Control of Storage Systems

Trabalho apresentado em 10th Electric Power Quality and Supply Reliability Conference, 29-31 de agosto, Tallin, EstóniaThis paper presents a study of a bidirectional dc-dc converter with high voltage gain to regulate the charge and discharge of electrochemical storage systems. The converter is characterized by quadratic voltage gain characteristics in both directions. In this context it can be used to regulate a dc interface between the storage system and a dc/ac converter connected to the electrical grid. It will be analysed the converter in ideal and non-ideal conditions. A control system to regulate the output voltages and currents are also proposed. Simulation results are presented in order to validate the control system associated to the converter for the charge/discharge of the storage system.N/