Characterization of 28 nm FDSOI MOS and application to the design of a low-power 2.4 GHz LNA

IoT is expected to connect billions of devices all over world in the next years, and in a near future, it is expected to use LR-WPAN in a wide variety of applications. Not all the devices will require of high performance but will require of low power hungry systems since most of them will be powered with a battery. Conventional CMOS technologies cannot cover these needs even scaling it to very small regimes, which appear other problems. Hence, new technologies are emerging to cover the needs of this devices. One promising technology is the UTBB FDSOI, which achieves good performance with very good energy efficiency. This project characterizes this technology to obtain a set of parameters of interest for analog/RF design. Finally, with the help of a low-power design methodology (gm/Id approach), a design of an ULP ULV LNA is performed to check the suitability of this technology for IoT

Design of variability compensation architectures of digital circuits with adaptive body bias

The most critical concern in circuit is to achieve high level of performance with very tight power constraint. As the high performance circuits moved beyond 45nm technology one of the major issues is the parameter variation i.e. deviation in process, temperature and voltage (PVT) values from nominal specifications. A key process parameter subject to variation is the transistor threshold voltage (Vth) which impacts two important parameters: frequency and leakage power. Although the degradation can be compensated by the worstcase scenario based over-design approach, it induces remarkable power and performance overhead which is undesirable in tightly constrained designs. Dynamic voltage scaling (DVS) is a more power efficient approach, however its coarse granularity implies difficulty in handling fine grained variations. These factors have contributed to the growing interest in power aware robust circuit design. We propose a variability compensation architecture with adaptive body bias, for low power applications using 28nm FDSOI technology. The basic approach is based on a dynamic prediction and prevention of possible circuit timing errors. In our proposal we are using a Canary logic technique that enables the typical-case design. The body bias generation is based on a DLL type method which uses an external reference generator and voltage controlled delay line (VCDL) to generate the forward body bias (FBB) control signals. The adaptive technique is used for dynamic detection and correction of path failures in digital designs due to PVT variations. Instead of tuning the supply voltage, the key idea of the design approach is to tune the body bias voltage bymonitoring the error rate during operation. The FBB increases operating speed with an overhead in leakage power

Low energy digital circuits in advanced nanometer technologies

The demand for portable devices and the continuing trend towards the Internet ofThings (IoT) have made of energy consumption one of the main concerns in the industry and researchers. The most efficient way of reducing the energy consump-tion of digital circuits is decreasing the supply voltage (Vdd) since the dynamicenergy quadratically depends onVdd. Several works have shown that an optimumsupply voltage exists that minimizes the energy consumption of digital circuits. This optimum supply voltage is usually around 200 mV and 400 mV dependingon the circuit and technology used. To obtain these low supply voltages, on-chipdc-dc converters with high efficiency are needed.This thesis focuses on the study of subthreshold digital systems in advancednanometer technologies. These systems usually can be divided into a Power Man-agement Unit (PMU) and a digital circuit operating at the subthreshold regime.In particular, while considering the PMU, one of the key circuits is the dc-dcconverter. This block converts the voltage from the power source (battery, supercapacitor or wireless power transfer link) to a voltage between 200 mV and 400mV in order to power the digital circuit. In this thesis, we developed two chargerecycling techniques in order to improve the efficiency of switched capacitors dc-dcconverters. The first one is based on a technique used in adiabatic circuits calledstepwise charging. This technique was used in circuits and applications wherethe switching consumption of a big capacitance is very important. We analyzedthe possibility of using this technique in switched capacitor dc-dc converters withintegrated capacitors. We showed through measurements that a 29% reductionin the gate drive losses can be obtained with this technique. The second one isa simplification of stepwise charging which can be applied in some architecturesof switched capacitors dc-dc converters. We also fabricated and tested a dc-dcconverter with this technique and obtained a 25% energy reduction in the drivingof the switches that implement the converter.Furthermore, we studied the digital circuit working in the subthreshold regime,in particular, operating at the minimum energy point. We studied different modelsfor circuits working in these conditions and improved them by considering thedifferences between the NMOS and PMOS transistors. We obtained an optimumNMOS/PMOS leakage current imbalance that minimizes the total leakage energy per operation. This optimum depends on the architecture of the digital circuitand the input data. However, we also showed that important energy reductionscan be obtained by operating at a mean optimum imbalance. We proposed two techniques to achieve the optimum imbalance. We used aFully Depleted Silicon on Insulator (FD-SOI) 28 nm technology for most of the simulations, but we also show that these techniques can be applied in traditionalbulk CMOS technologies. The first one consists in using the back plane voltage of the transistors (or bulk voltage in traditional CMOS) to adjust independently theleakage current of the NMOS and PMOS transistor to work under the optimum NMOS/PMOS leakage current imbalance. We called this approach the OptimumBack Plane Biasing (OBB). A second technique consists of using the length of the transistors to adjust this leakage current imbalance. In the subthreshold regimeand in advanced nanometer technologies a moderate increase in the length has little impact in the output capacitance of the gates and thus in the dynamic energy.We called this approach an Asymmetric Length Biasing (ALB). Finally, we use these techniques in some basic circuits such as adders. We show that around 50% energy reduction can be obtained, in a wide range of frequency while working near the minimum energy point and using these techniques. The main contributions of this thesis are: • Analysis of the stepwise charging technique in small capacitances. •Implementation of stepwise charging technique as a charge recycling tech-nique for efficiency improvement in switched capacitor dc-dc converters. • Development of a charge sharing technique for efficiency improvement inswitched capacitor dc-dc converters. • Analysis of minimum operating voltage of digital circuits due to intrinsicnoise and the impact of technology scaling in this minimum. • Improvement in the modeling of the minimum energy point while considering NMOS and PMOS transistors difference. • Demonstration of the existence of an optimum leakage current imbalance be-tween the NMOS and PMOS transistors that minimizes energy consumptionin the subthreshold regiion. • Development of a back plane (bulk) voltage strategy for working in this optimum.• Development of a sizing strategy for working in the aforementioned optimum. • Analysis of the impact of architecture and input data on the optimum im-balance. The thesis is based on the publications [1–8]. During the Ph.D. program, other publications were generated [9–16] that are partially related with the thesis butwere not included in it.La constante demanda de dispositivos portables y los avances hacia la Internet de las Cosas han hecho del consumo de energía uno de los mayores desafíos y preocupación en la industria y la academia. La forma más eficiente de reducir el consumo de energía de los circuitos digitales es reduciendo su voltaje de alimentación ya que la energía dinámica depende de manera cuadrática con dicho voltaje. Varios trabajos demostraron que existe un voltaje de alimentación óptimo, que minimiza la energía consumida para realizar cierta operación en un circuito digital, llamado punto de mínima energía. Este óptimo voltaje se encuentra usualmente entre 200 mV y 400 mV dependiendo del circuito y de la tecnología utilizada. Para obtener estos voltajes de alimentación de la fuente de energía, se necesitan conversores dc-dc integrados con alta eficiencia. Esta tesis se concentra en el estudio de sistemas digitales trabajando en la región sub umbral diseñados en tecnologías nanométricas avanzadas (28 nm). Estos sistemas se pueden dividir usualmente en dos bloques, uno llamado bloque de manejo de potencia, y el segundo, el circuito digital operando en la region sub umbral. En particular, en lo que corresponde al bloque de manejo de potencia, el circuito más crítico es en general el conversor dc-dc. Este circuito convierte el voltaje de una batería (o super capacitor o enlace de transferencia inalámbrica de energía o unidad de cosechado de energía) en un voltaje entre 200 mV y 400 mV para alimentar el circuito digital en su voltaje óptimo. En esta tesis desarrollamos dos técnicas que, mediante el reciclado de carga, mejoran la eficiencia de los conversores dc-dc a capacitores conmutados. La primera es basada en una técnica utilizada en circuitos adiabáticos que se llama carga gradual o a pasos. Esta técnica se ha utilizado en circuitos y aplicaciones en donde el consumo por la carga y descarga de una capacidad grande es dominante. Nosotros analizamos la posibilidad de utilizar esta técnica en conversores dc-dc a capacitores conmutados con capacitores integrados. Se demostró a través de medidas que se puede reducir en un 29% el consumo debido al encendido y apagado de las llaves que implementan el conversor dc-dc. La segunda técnica, es una simplificación de la primera, la cual puede ser aplicada en ciertas arquitecturas de conversores dc-dc a capacitores conmutados. También se fabricó y midió un conversor con esta técnica y se obtuvo una reducción del 25% en la energía consumida por el manejo de las llaves del conversor. Por otro lado, estudiamos los circuitos digitales operando en la región sub umbral y en particular cerca del punto de mínima energía. Estudiamos diferentes modelos para circuitos operando en estas condiciones y los mejoramos considerando las diferencias entre los transistores NMOS y PMOS. Mediante este modelo demostramos que existe un óptimo en la relación entre las corrientes de fuga de ambos transistores que minimiza la energía de fuga consumida por operación. Este óptimo depende de la arquitectura del circuito digital y ademas de los datos de entrada del circuito. Sin embargo, demostramos que se puede reducir el consumo de manera considerable al operar en un óptimo promedio. Propusimos dos técnicas para alcanzar la relación óptima. Utilizamos una tecnología FD-SOI de 28nm para la mayoría de las simulaciones, pero también mostramos que estas técnicas pueden ser utilizadas en tecnologías bulk convencionales. La primer técnica, consiste en utilizar el voltaje de la puerta trasera (o sustrato en CMOS convencional) para ajustar de manera independiente las corrientes del NMOS y PMOS para que el circuito trabaje en el óptimo de la relación de corrientes. Esta técnica la llamamos polarización de voltaje de puerta trasera óptimo. La segunda técnica, consiste en utilizar los largos de los transistores para ajustar las corrientes de fugas de cada transistor y obtener la relación óptima. Trabajando en la región sub umbral y en tecnologías avanzadas, incrementar moderadamente el largo del transistor tiene poco impacto en la energía dinámica y es por eso que se puede utilizar. Finalmente, utilizamos estas técnicas en circuitos básicos como sumadores y mostramos que se puede obtener una reducción de la energía consumida de aproximadamente 50%, en un amplio rango de frecuencias, mientras estos circuitos trabajan cerca del punto de energía mínima. Las principales contribuciones de la tesis son: • Análisis de la técnica de carga gradual o a pasos en capacidades pequeñas. • Implementación de la técnica de carga gradual para la mejora de eficiencia de conversores dc-dc a capacitores conmutados. • Simplificación de la técnica de carga gradual para mejora de la eficiencia en algunas arquitecturas de conversores dc-dc de capacitores conmutados. • Análisis del mínimo voltaje de operación en circuitos digitales debido al ruido intrínseco del dispositivo y el impacto del escalado de las tecnologías en el mismo. • Mejoras en el modelado del punto de energía mínima de operación de un circuito digital en el cual se consideran las diferencias entre el transistor PMOS y NMOS. • Demostración de la existencia de un óptimo en la relación entre las corrientes de fuga entre el NMOS y PMOS que minimiza la energía de fugas consumida en la región sub umbral. • Desarrollo de una estrategia de polarización del voltaje de puerta trasera para que el circuito digital trabaje en el óptimo antes mencionado. • Desarrollo de una estrategia para el dimensionado de los transistores que componen las compuertas digitales que permite al circuito digital operar en el óptimo antes mencionado. • Análisis del impacto de la arquitectura del circuito y de los datos de entrada del mismo en el óptimo antes mencionado

FDSOI Design using Automated Standard-Cell-Grained Body Biasing

With the introduction of FDSOI processes at competitive technology nodes, body biasing on an unprecedented scale was made possible. Body biasing influences one of the central transistor characteristics, the threshold voltage. By being able to heighten or lower threshold voltage by more than 100mV, the very physics of transistor switching can be manipulated at run time. Furthermore, as body biasing does not lead to different signal levels, it can be applied much more fine-grained than, e.g., DVFS. With the state of the art mainly focused on combinations of body biasing with DVFS, it has thus ignored granularities unfeasible for DVFS. This thesis fills this gap by proposing body bias domain partitioning techniques and for body bias domain partitionings thereby generated, algorithms that search for body bias assignments. Several different granularities ranging from entire cores to small groups of standard cells were examined using two principal approaches: Designer aided pre-partitioning based determination of body bias domains and a first-time, fully automatized, netlist based approach called domain candidate exploration. Both approaches operate along the lines of activation and timing of standard cell groups. These approaches were evaluated using the example of a Dynamically Reconfigurable Processor (DRP), a highly efficient category of reconfigurable architectures which consists of an array of processing elements and thus offers many opportunities for generalization towards many-core architectures. Finally, the proposed methods were validated by manufacturing a test-chip. Extensive simulation runs as well as the test-chip evaluation showed the validity of the proposed methods and indicated substantial improvements in energy efficiency compared to the state of the art. These improvements were accomplished by the fine-grained partitioning of the DRP design. This method allowed reducing dynamic power through supply voltage levels yielding higher clock frequencies using forward body biasing, while simultaneously reducing static power consumption in unused parts.Die Einführung von FDSOI Prozessen in gegenwärtigen Prozessgrößen ermöglichte die Nutzung von Substratvorspannung in nie zuvor dagewesenem Umfang. Substratvorspannung beeinflusst unter anderem eine zentrale Eigenschaft von Transistoren, die Schwellspannung. Mittels Substratvorspannung kann diese um mehr als 100mV erhöht oder gesenkt werden, was es ermöglicht, die schiere Physik des Schaltvorgangs zu manipulieren. Da weiterhin hiervon der Signalpegel der digitalen Signale unberührt bleibt, kann diese Technik auch in feineren Granularitäten angewendet werden, als z.B. Dynamische Spannungs- und Frequenz Anpassung (Engl. Dynamic Voltage and Frequency Scaling, Abk. DVFS). Da jedoch der Stand der Technik Substratvorspannung hauptsächlich in Kombinationen mit DVFS anwendet, werden feinere Granularitäten, welche für DVFS nicht mehr wirtschaftlich realisierbar sind, nicht berücksichtigt. Die vorliegende Arbeit schließt diese Lücke, indem sie Partitionierungsalgorithmen zur Unterteilung eines Entwurfs in Substratvorspannungsdomänen vorschlägt und für diese hierdurch unterteilten Domänen entsprechende Substratvorspannungen berechnet. Hierzu wurden verschiedene Granularitäten berücksichtigt, von ganzen Prozessorkernen bis hin zu kleinen Gruppen von Standardzellen. Diese Entwürfe wurden dann mit zwei verschiedenen Herangehensweisen unterteilt: Chipdesigner unterstützte, vorpartitionierungsbasierte Bestimmung von Substratvorspannungsdomänen, sowie ein erstmals vollautomatisierter, Netzlisten basierter Ansatz, in dieser Arbeit Domänen Kandidaten Exploration genannt. Beide Ansätze funktionieren nach dem Prinzip der Aktivierung, d.h. zu welchem Zeitpunkt welcher Teil des Entwurfs aktiv ist, sowie der Signallaufzeit durch die entsprechenden Entwurfsteile. Diese Ansätze wurden anhand des Beispiels Dynamisch Rekonfigurierbarer Prozessoren (DRP) evaluiert. DRPs stellen eine Klasse hocheffizienter rekonfigurierbarer Architekturen dar, welche hauptsächlich aus einem Feld von Rechenelementen besteht und dadurch auch zahlreiche Möglichkeiten zur Verallgemeinerung hinsichtlich Many-Core Architekturen zulässt. Schließlich wurden die vorgeschlagenen Methoden in einem Testchip validiert. Alle ermittelten Ergebnisse zeigen im Vergleich zum Stand der Technik drastische Verbesserungen der Energieeffizienz, welche durch die feingranulare Unterteilung in Substratvorspannungsdomänen erzielt wurde. Hierdurch konnten durch die Anwendung von Substratvorspannung höhere Taktfrequenzen bei gleicher Versorgungsspannung erzielt werden, während zeitgleich in zeitlich unkritischen oder ungenutzten Entwurfsteilen die statische Leistungsaufnahme minimiert wurde

Embedding Logic and Non-volatile Devices in CMOS Digital Circuits for Improving Energy Efficiency

abstract: Static CMOS logic has remained the dominant design style of digital systems for more than four decades due to its robustness and near zero standby current. Static CMOS logic circuits consist of a network of combinational logic cells and clocked sequential elements, such as latches and flip-flops that are used for sequencing computations over time. The majority of the digital design techniques to reduce power, area, and leakage over the past four decades have focused almost entirely on optimizing the combinational logic. This work explores alternate architectures for the flip-flops for improving the overall circuit performance, power and area. It consists of three main sections. First, is the design of a multi-input configurable flip-flop structure with embedded logic. A conventional D-type flip-flop may be viewed as realizing an identity function, in which the output is simply the value of the input sampled at the clock edge. In contrast, the proposed multi-input flip-flop, named PNAND, can be configured to realize one of a family of Boolean functions called threshold functions. In essence, the PNAND is a circuit implementation of the well-known binary perceptron. Unlike other reconfigurable circuits, a PNAND can be configured by simply changing the assignment of signals to its inputs. Using a standard cell library of such gates, a technology mapping algorithm can be applied to transform a given netlist into one with an optimal mixture of conventional logic gates and threshold gates. This approach was used to fabricate a 32-bit Wallace Tree multiplier and a 32-bit booth multiplier in 65nm LP technology. Simulation and chip measurements show more than 30% improvement in dynamic power and more than 20% reduction in core area. The functional yield of the PNAND reduces with geometry and voltage scaling. The second part of this research investigates the use of two mechanisms to improve the robustness of the PNAND circuit architecture. One is the use of forward and reverse body biases to change the device threshold and the other is the use of RRAM devices for low voltage operation. The third part of this research focused on the design of flip-flops with non-volatile storage. Spin-transfer torque magnetic tunnel junctions (STT-MTJ) are integrated with both conventional D-flipflop and the PNAND circuits to implement non-volatile logic (NVL). These non-volatile storage enhanced flip-flops are able to save the state of system locally when a power interruption occurs. However, manufacturing variations in the STT-MTJs and in the CMOS transistors significantly reduce the yield, leading to an overly pessimistic design and consequently, higher energy consumption. A detailed analysis of the design trade-offs in the driver circuitry for performing backup and restore, and a novel method to design the energy optimal driver for a given yield is presented. Efficient designs of two nonvolatile flip-flop (NVFF) circuits are presented, in which the backup time is determined on a per-chip basis, resulting in minimizing the energy wastage and satisfying the yield constraint. To achieve a yield of 98%, the conventional approach would have to expend nearly 5X more energy than the minimum required, whereas the proposed tunable approach expends only 26% more energy than the minimum. A non-volatile threshold gate architecture NV-TLFF are designed with the same backup and restore circuitry in 65nm technology. The embedded logic in NV-TLFF compensates performance overhead of NVL. This leads to the possibility of zero-overhead non-volatile datapath circuits. An 8-bit multiply-and- accumulate (MAC) unit is designed to demonstrate the performance benefits of the proposed architecture. Based on the results of HSPICE simulations, the MAC circuit with the proposed NV-TLFF cells is shown to consume at least 20% less power and area as compared to the circuit designed with conventional DFFs, without sacrificing any performance.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

Approche industrielle aux boîtes quantiques dans des dispositifs de silicium sur isolant complètement déplété pour applications en information quantique

La mise en oeuvre des qubits de spin électronique à base de boîtes quantiques réalisés en utilisant une technologie avancée de métal-oxyde-semiconducteur complémentaire (en anglais: CMOS ou Complementary Metal-Oxide-Semiconductor) fonctionnant à des températures cryogéniques permet d’envisager la fabrication industrielle reproductible et à haut rendement de systèmes de qubits de spin à grande échelle. Le développement d’une architecture de boîtes quantiques à base de silicium fabriquées en utilisant exclusivement des techniques de fabrication industrielle CMOS constitue une étape majeure dans cette direction. Dans cette thèse, le potentiel de la technologie UTBB (en anglais: Ultra-Thin Body and Buried oxide) silicium sur isolant complétement déplété (en anglais: FD-SOI ou Fully Depleted Silicon-On-Insulator) 28 nm de STMicroelectronics (Crolles, France) a été étudié pour la mise en oeuvre de boîtes quantiques bien définies, capables de réaliser des systèmes de qubit de spin. Dans ce contexte, des mesures d’effet Hall ont été réalisées sur des microstructures FD-SOI à 4.2 K afin de déterminer la qualité du noeud technologique pour les applications de boîtes quantiques. De plus, un flot du processus d’intégration, optimisé pour la mise en oeuvre de dispositifs quantiques utilisant exclusivement des méthodes de fonderie de silicium pour la production de masse est présenté, en se concentrant sur la réduction des risques de fabrication et des délais d’exécution globaux. Enfin, deux géométries différentes de dispositifs à boîtes quantiques FD-SOI de 28nm ont été conçues et leurs performances ont été étudiées à 1.4 K. Dans le cadre d’une collaboration entre Nanoacademic Technologies, Institut quantique et STMicroelectronics, un modèle QTCAD (en anglais: Quantum Technology Computer-Aided Design) en 3D a été développé pour la modélisation de dispositifs à boîtes quantiques FD-SOI. Ainsi, en complément de la caractérisation expérimentale des structures de test via des mesures de transport et de spectroscopie de blocage de Coulomb, leur performance est modélisée et analysée à l’aide du logiciel QTCAD. Les résultats présentés ici démontrent les avantages de la technologie FD-SOI par rapport à d’autres approches pour les applications de calcul quantique, ainsi que les limites identifiées du noeud 28 nm dans ce contexte. Ce travail ouvre la voie à la mise en oeuvre des nouvelles générations de dispositifs à boîtes quantiques FD-SOI basées sur des noeuds technologiques inférieurs.Abstract: Electron spin qubits based on quantum dots implemented using advanced Complementary Metal-Oxide-Semiconductor (CMOS) technology functional at cryogenic temperatures promise to enable reproducible high-yield industrial manufacturing of large-scale spin qubit systems. A milestone in this direction is to develop a silicon-based quantum dot structure fabricated using exclusively CMOS industrial manufacturing techniques. In this thesis, the potential of the industry-standard process 28 nm Ultra-Thin Body and Buried oxide (UTBB) Fully Depleted Silicon-On-Insulator (FD-SOI) technology of STMicroelectronics (Crolles, France) was investigated for the implementation of well-defined quantum dots capable to realize spin qubit systems. In this context, Hall effect measurements were performed on FD-SOI microstructures at 4.2 K to determine the quality of the technology node for quantum dot applications. Moreover, an optimized integration process flow for the implementation of quantum devices, using exclusively mass-production silicon-foundry methods is presented, focusing on reducing manufacturing risks and overall turnaround times. Finally, two different geometries of 28 nm FD-SOI quantum dot devices were conceived, and their performance was studied at 1.4 K. In the framework of a collaboration between Nanoacademic Technologies, Institut quantique, and STMicroelectronics, a 3D Quantum Technology Computer-Aided Design (QTCAD) model was developed for FD-SOI quantum dot device modeling. Therefore, along with the experimental characterization of the test structures via transport and Coulomb blockade spectroscopy measurements, their performance is modeled and analyzed using the QTCAD software. The results reported here demonstrate the advantages of the FD-SOI technology over other approaches for quantum computing applications, as well as the identified limitations of the 28 nm node in this context. This work paves the way for the implementation of the next generations of FD-SOI quantum dot devices based on lower technology nodes

Design of a RF communication receiver front-end for ultra-low power and voltage applications in a FDSOI 28nm technology

The advances in the semiconductor and wireless industry have enabled the expansion of new paradigms, which have given rise to concepts like Internet of Things (IoT). Apart from qualities like size, speed or cost, the ever-increasing demand for autonomy focuses all design efforts in the minimization of power consumption. Scaling technologies and the request to reduce power consumption have pushed designers towards lower supply voltages. Despite the fact that technology scalability allows for faster transistors, radio-frequency (RF) integrated circuit (IC) design accuses the reduction of the voltage supply through frequency response degradation, which significantly deteriorates the overall performance. Analog and RF circuits in highend applications require substantial gate voltage overdrive to maintain device speed, which further complicates the design due to the reduction of voltage headroom. As a consequence, the necessity to develop circuit topologies capable to deal with low-power and low-voltage stringent constraints well suited to applications requiring long battery life and low cost emerges. This work aims to implement a low-noise amplifier and mixer stages of a radio-frequency receiver front-end working under an ultra-low power (< 100 ?W) and ultra-low voltage (< 0.8V) scenario while targeting decent overall performance. To cope with the stringent power requirements, 28nm FD-SOI technology will be used to take maximum profit of aggressive forward body bias and enhance transistor performance

Low-Temperature Technologies and Applications

This book on low-temperature technology is a notable collection of different aspects of the technology and its application in varieties of research and practical engineering fields. It contains, sterilization and preservation techniques and their engineering and scientific characteristics. Ultra-low temperature refrigeration, the refrigerants, applications, and economic aspects are highlighted in this issue. The readers will find the low temperature, and vacuum systems for industrial applications. This book has given attention to global energy resources, conservation of energy, and alternative sources of energy for the application of low-temperature technologies