A low-speed BIST framework for high-performance circuit testing

Testing of high performance integrated circuits is becoming increasingly a challenging task owing to high clock frequencies. Often testers are not able to test such devices due to their limited high frequency capabilities. In this article we outline a design-for-test methodology such that high performance devices can be tested on relatively low performance testers. In addition, a BIST framework is discussed based on this methodology. Various implementation aspects of this technique are also addresse

IDDQ testing of a CMOS first order sigma-delta modulator of an 8-bit oversampling ADC

This work presents IDDQ testing of a CMOS first order sigma-delta modulator of an 8-bit oversampling analog-to-digital converter using a built-in current sensor [BICS]. Gate-drain, source-drain, gate-source and gate-substrate bridging faults are injected using fault injection transistors. All the four faults cause varying fault currents and are successfully detected by the BICS at a good operation speed. The BICS have a negligible impact on the performance of the modulator and an external pin is provided to completely cut-off the BICS from the modulator. The modulator was designed and fabricated in 1.5 μm n-well CMOS process. The decimator was designed on Altera\u27s FLEXE20K board using Verilog. The modulator and decimator were assembled together to form a sigma-delta ADC

Quiescent current testing of CMOS data converters

Power supply quiescent current (IDDQ) testing has been very effective in VLSI circuits designed in CMOS processes detecting physical defects such as open and shorts and bridging defects. However, in sub-micron VLSI circuits, IDDQ is masked by the increased subthreshold (leakage) current of MOSFETs affecting the efficiency of I¬DDQ testing. In this work, an attempt has been made to perform robust IDDQ testing in presence of increased leakage current by suitably modifying some of the test methods normally used in industry. Digital CMOS integrated circuits have been tested successfully using IDDQ and IDDQ methods for physical defects. However, testing of analog circuits is still a problem due to variation in design from one specific application to other. The increased leakage current further complicates not only the design but also testing. Mixed-signal integrated circuits such as the data converters are even more difficult to test because both analog and digital functions are built on the same substrate. We have re-examined both IDDQ and IDDQ methods of testing digital CMOS VLSI circuits and added features to minimize the influence of leakage current. We have designed built-in current sensors (BICS) for on-chip testing of analog and mixed-signal integrated circuits. We have also combined quiescent current testing with oscillation and transient current test techniques to map large number of manufacturing defects on a chip. In testing, we have used a simple method of injecting faults simulating manufacturing defects invented in our VLSI research group. We present design and testing of analog and mixed-signal integrated circuits with on-chip BICS such as an operational amplifier, 12-bit charge scaling architecture based digital-to-analog converter (DAC), 12-bit recycling architecture based analog-to-digital converter (ADC) and operational amplifier with floating gate inputs. The designed circuits are fabricated in 0.5 μm and 1.5 μm n-well CMOS processes and tested. Experimentally observed results of the fabricated devices are compared with simulations from SPICE using MOS level 3 and BSIM3.1 model parameters for 1.5 μm and 0.5 μm n-well CMOS technologies, respectively. We have also explored the possibility of using noise in VLSI circuits for testing defects and present the method we have developed

Iddq testing of a CMOS 10-bit charge scaling digital-to-analog converter

This work presents an effective built-in current sensor (BICS), which has a very small impact on the performance of the circuit under test (CUT). The proposed BICS works in two-modes the normal mode and the test mode. In the normal mode the BICS is isolated from the CUT due to which there is no performance degradation of the CUT. In the testing mode, our BICS detects the abnormal current caused by permanent manufacturing defects. Further more our BICS can also distinguish the type of defect induced (Gate-source short, source-drain short and drain-gate short). Our BICS requires neither an external voltage source nor current source. Hence the BICS requires less area and is more efficient than the conventional current sensors. The circuit under test is a 10-bit digital to analog converter using charge-scaling architecture

A design for testability study on a high performance automatic gain control circuit.

A comprehensive testability study on a commercial automatic gain control circuit is presented which aims to identify design for testability (DfT) modifications to both reduce production test cost and improve test quality. A fault simulation strategy based on layout extracted faults has been used to support the study. The paper proposes a number of DfT modifications at the layout, schematic and system levels together with testability. Guidelines that may well have generic applicability. Proposals for using the modifications to achieve partial self test are made and estimates of achieved fault coverage and quality levels presente

Testing a CMOS operational amplifier circuit using a combination of oscillation and IDDQ test methods

This work presents a case study, which attempts to improve the fault diagnosis and testability of the oscillation testing methodology applied to a typical two-stage CMOS operational amplifier. The proposed test method takes the advantage of good fault coverage through the use of a simple oscillation based test technique, which needs no test signal generation and combines it with quiescent supply current (IDDQ) testing to provide a fault confirmation. A built in current sensor (BICS), which introduces insignificant performance degradation of the circuit-under-test (CUT), has been utilized to monitor the power supply quiescent current changes in the CUT. The testability has also been enhanced in the testing procedure using a simple fault-injection technique. The approach is attractive for its simplicity, robustness and capability of built-in-self test (BIST) implementation. It can also be generalized to the oscillation based test structures of other CMOS analog and mixed-signal integrated circuits. The practical results and simulations confirm the functionality of the proposed test method

[Delta] IDDQ testing of a CMOS 12-bit charge scaling digital-to-analog converter

This work presents design, implementation and test of a built-in current sensor (BICS) for ∆IDDQ testing of a CMOS 12-bit charge scaling digital-to-analog converter (DAC). The sensor uses power discharge method for the fault detection. The sensor operates in two modes, the test mode and the normal mode. In the test mode, the BICS is connected to the circuit under test (CUT) which is DAC and detects abnormal currents caused by manufacturing defects. In the normal mode, BICS is isolated from the CUT. The BICS is integrated with the DAC and is implemented in a 0.5 μm n-well CMOS technology. The DAC uses charge scaling method for the design and a low voltage (0 to 2.5 V) folded cascode op-amp. The built-in current sensor (BICS) has a resolution of 0.5 μA. Faults have been introduced into DAC using fault injection transistors (FITs). The method of ∆IDDQ testing has been verified both from simulation and experimental measurements

IDDQ Testing of Low Voltage CMOS Operational Transconductance Amplifier

The paper describes the design for testability (DFT) of low voltage two stage operational transconductance amplifiers based on quiescent power supply current (IDDQ) testing. IDDQ testing refers to the integral circuit testing method based upon measurement of steady state power supply current for testing both digital as well as analog VLSI circuit. A built in current sensor, which introduces insignificant performance degradation of the circuit-under-test, has been proposed to monitor the power supply quiescent current changes in the circuit under test. Moreover, the BICS requires neither an external voltage reference nor a current source and able to detect, identify and localize the circuit faults. Hence the BICS requires less area and is more efficient than the conventional current sensors. The testability has also been enhanced in the testing procedure using a simple fault-injection technique. Both bridging and open faults have been analyzed in proposed work by using n-well 0.18µm CMOS technology

A Behavioral Model of a Built-in Current Sensor for IDDQ Testing

IDDQ testing is one of the most effective methods for detecting defects in integrated circuits. Higher leakage currents in more advanced semiconductor technologies have reduced the resolution of IDDQ test. One solution is to use built-in current sensors. Several sensor techniques for measuring the current based on the magnetic field or voltage drop across the supply line have been proposed. In this work, we develop a behavioral model for a built-in current sensor measuring voltage drop and use this model to better understand sensor operation, identify the effect of different parameters on sensor resolution, and suggest design modifications to improve future sensor performance