Applications of Wireless Power Transfer in Medicine : State-of-the-Art Reviews

Magnetic resonance within the field of wireless power transfer has seen an increase in popularity over the past decades. This rise can be attributed to the technological advances of electronics and the increased efficiency of popular battery technologies. The same principles of electromagnetic theory can be applied to the medical field. Several medical devices intended for use inside the body use batteries and electrical circuits that could be powered wirelessly. Other medical devices limit the mobility or make patients uncomfortable while in use. The fundamental theory of electromagnetics can improve the field by solving some of these problems. This survey paper summarizes the recent uses and discoveries of wireless power in the medical field. A comprehensive search for papers was conducted using engineering search engines and included papers from related conferences. During the initial search, 247 papers were found then non-relevant papers were eliminated to leave only suitable material. Seventeen relevant journal papers and/or conference papers were found, then separated into defined categories: Implants, Pumps, Ultrasound Imaging, and Gastrointestinal (GI) Endoscopy. The approach and methods for each paper were analyzed and compared yielding a comprehensive review of these state of the art technologies

Tracking and dynamic tuning of a wireless powered endoscopic capsule

This work presents an inductive wireless power transfer system for powering an endoscopy capsule supplying energy to power electronic devices allocated inside a capsule of ≈26.1 mm × 9 mm. A receiver with three coils in quadrature with dimensions of ≈9 mm × 9 mm × 10 mm is located inside the capsule, moving freely inside a transmitter coil with 380 mm diameter through translations and revolutions. The proposed system tracks the variations of the equivalent magnetic coupling coefficient compensating misalignments between the transmitter and receiver coils. The power on the load is estimated and optimized from the transmitter, and the tracking control is performed by actuating on a capacitance in the matching network and on the voltage source frequency. The proposed system can prevent load overheating by limiting the power via adjusting of the magnitude of voltage source VS. Experimental results with uncertainties analysis reveal that, even at low magnetic coupling coefficients k ranging from (1.7 × 10−3 , 3.5 × 10−3 ), the power on the load can be held within the range of 100–130 mW. These results are achieved with any position of the capsule in the space, limited by the diameter of the transmitter coil and height of 200 mm when adjusting the series capacitance of the transmitter in the range (17.4, 19.4) pF and the frequency of the power source in the range (802.1, 809.5) kHz

Wireless Power Transfer Techniques for Implantable Medical Devices:A Review

Wireless power transfer (WPT) systems have become increasingly suitable solutions for the electrical powering of advanced multifunctional micro-electronic devices such as those found in current biomedical implants. The design and implementation of high power transfer efficiency WPT systems are, however, challenging. The size of the WPT system, the separation distance between the outside environment and location of the implanted medical device inside the body, the operating frequency and tissue safety due to power dissipation are key parameters to consider in the design of WPT systems. This article provides a systematic review of the wide range of WPT systems that have been investigated over the last two decades to improve overall system performance. The various strategies implemented to transfer wireless power in implantable medical devices (IMDs) were reviewed, which includes capacitive coupling, inductive coupling, magnetic resonance coupling and, more recently, acoustic and optical powering methods. The strengths and limitations of all these techniques are benchmarked against each other and particular emphasis is placed on comparing the implanted receiver size, the WPT distance, power transfer efficiency and tissue safety presented by the resulting systems. Necessary improvements and trends of each WPT techniques are also indicated per specific IMD

A Network Approach for Wireless Resonant Energy Links Using Relay Resonators

In this paper, a network approach for the analysis of a wireless resonant energy link consisting of N inductively coupled LC resonators is proposed. By using an artificial transmission line approach, the wireless link is modeled as a transmission line described by effective parameters. It is shown that the analyzed system exhibits a passband filter behavior. More specifically, the reported results demonstrate that in the wireless link passband the effective parameters assume negative values resulting in a negative phase delay. Useful design formulas are derived and validated by comparisons with the experimental data

Coil geometry models for power loss analysis and hybrid inductive link for wireless power transfer applications

This paper presents a hybrid inductive link for Wireless Power Transfer (WPT) applications. Achieving better power transfer efficiency over a relatively wider distance across coils is the prime objective in most of the WPT systems, but often suffers from power loss in the near field area of inductively coupled coils. One of the reasons for this power loss is the pattern of the magnetic field produced by the source coil used in the WPT system. Mostly the nature of magnetic field produced by the source coil is distributed radially over the coil, in which the produced magnetic field is not fully utilized. Achieving better efficiency and load current by reducing power loss is the main driving force of this work. One of the viable methods to reduce the power loss is by increasing the field intensity thereby redirecting the flux lines flow to be directional. With this aim, three coils such as solenoid, spiral and conical are designed and simulated to determine the magnetic field strength using Finite Element Method. The conical coil produces the highest self-inductance of 8.63 lH and a field strength of 1.542 Wb with the coil thickness of 3.20 mm. Then, WPT system is demonstrated with the inclusion of Maximum Power Point Tracking algorithm for improving efficiency. The schematic of flux generation of both in the transmitter and receiver sections are demonstrated and analyzed graphically. The efficiency of both simulation and experimental measurements are matched well with similar progression. The effect of parameters (angle, distance, and load resistance) on the efficiency is explored. The outcomes conclude that the inductive coupling has achieved 73% (average case) power transfer wirelessly over a distance of 5 cm with an input voltage of 5 V and 5 MHz frequency

Estudo de um sistema de transmissão de energia sem fios para cápsula endoscópica

A transferência de energia sem fios (WPT, wireless power transfer) tem sido utilizada para alimentação de dispositivos e sistemas, em que o uso de cabos é inadequado, custoso ou até mesmo proibitivo. As suas aplicações abrangem desde dispositivos biomédicos implantáveis, passando pelo setor de eletrônicos de consumo, até recarga de baterias em veículos elétricos. A potência transferida à carga por meio do WPT depende dos parâmetros do circuito equivalente do link indutivo. Mesmo com esses parâmetros fixos, a potência entregue à carga é influenciada por desalinhamentos entre as bobinas transmissora e receptora, bem como condições de carga variável. Esse trabalho apresenta a análise matemática, modelagem e proposta de um método de projeto de um sistema de transmissão de energia sem-fios aplicado ao problema de uma cápsula endoscópica. Esse problema é bastante particular por apresentar um receptor com três bobinas em quadratura. Além disso a bobina transmissora apresenta um diâmetro de aproximadamente 30 vezes o diâmetro das bobinas receptoras. O sistema é projetado para otimizar a potência transmitida para uma cápsula engolível com posição e orientação arbitrárias ao longo de uma distância equivalente ao trato digestivo. Os resultados mostraram que é possível garantir uma potência mínima na carga de 100 mW em todo o trajeto da cápsula, suficiente para coletar e transmitir imagens do interior do trato digestivo até um receptor externo.Wireless power transfer (WPT) has been used to power devices and systems, in which the use of cables is distorted, costly or even prohibitive. Its applications range from implantable biomedical devices, through the consumer electronics sector, to battery recharging in electric vehicles. The power transferred to the load through the WPT depends on the parameters of the equivalent circuit of the inductive link. Even with these fixed parameters, the power delivered to the load is influenced by misalignments between the transmitting and receiving coils, as well as the variable load conditions. This work presents a mathematical analysis, modeling and proposal of a design method for a wireless energy transmission system converted to the problem of an endoscopic capsule. This problem is very particular because it has a receiver with three quadrature coils. In addition, a transmitting coil presents diameter of approximate 30 times the diameter of the receiving coils. The system is designed to optimize the power transmitted to a swallowable capsule with arbitrary position and orientation over a distance equivalent to the digestive tract. The possible results are that it is possible to guarantee a minimum load power of 100 mW throughout the capsule path, sufficient to collect and transmit images from the inside of the digestive tract to an external receptor

Q-learning Channel Access Methods for Wireless Powered Internet of Things Networks

The Internet of Things (IoT) is becoming critical in our daily life. A key technology of interest in this thesis is Radio Frequency (RF) charging. The ability to charge devices wirelessly creates so called RF-energy harvesting IoT networks. In particular, there is a hybrid access point (HAP) that provides energy in an on-demand manner to RF-energy harvesting devices. These devices then collect data and transmit it to the HAP. In this respect, a key issue is ensuring devices have a high number of successful transmissions. There are a number of issues to consider when scheduling the transmissions of devices in the said network. First, the channel gain to/from devices varies over time. This means the efficiency to deliver energy to devices and to transmit the same amount of data is different over time. Second, during channel access, devices are not aware of the energy level of other devices nor whether they will transmit data. Third, devices have non-causal knowledge of their energy arrivals and channel gain information. Consequently, they do not know whether they should delay their transmissions in hope of better channel conditions or less contention in future time slots or doing so would result in energy overflow

Wireless Power Transfer For Biomedical Applications

In this research wireless power transfer using near-field inductive coupling is studied and investigated. The focus is on delivering power to implantable biomedical devices. The objective of this research is to optimize the size and performance of the implanted wireless biomedical sensors by: (1) proposing a hybrid multiband communication system for implantable devices that combines wireless communication link and power transfer, and (2) optimizing the wireless power delivery system. Wireless data and power links are necessary for many implanted biomedical devices such as biosensors, neural recording and stimulation devices, and drug delivery and monitoring systems. The contributions from this research work are summarized as follows: 1. Development of a combination of inductive power transfer and antenna system. 2. Design and optimization of novel microstrip antenna that may resonate at different ultra-high frequency bands including 415 MHz, 905 MHz, and 1300MHz. These antennas may be used to transfer power through radiation or send/receive data. 3. Design of high-frequency coil (13.56 MHz) to transfer power and optimization of the parameters for best efficiency. 4. Study of the performance of the hybrid antenna/coil system at various depths inside a body tissue model. 5. Minimizing the coupling effect between the coil and the antenna through addressed by optimizing their dimensions. 6. Study of the effects of lateral and angular misalignment on a hybrid compact system consisting of coil and antenna, as well as design and optimize the coilâs geometry which can provide maximum power efficiency under misalignment conditions. 7. Address the effects of receiver bending of a hybrid power transfer and communication system on the communication link budget and the transmitted power. 8. Study the wireless power transfer safety and security systems

Inductively Coupled CMOS Power Receiver For Embedded Microsensors

Inductively coupled power transfer can extend the lifetime of embedded microsensors that save costs, energy, and lives. To expand the microsensors' functionality, the transferred power needs to be maximized. Plus, the power receiver needs to handle wide coupling variations in real applications. Therefore, the objective of this research is to design a power receiver that outputs the highest power for the widest coupling range. This research proposes a switched resonant half-bridge power stage that adjusts both energy transfer frequency and duration so the output power is maximally high. A maximum power point (MPP) theory is also developed to predict the optimal settings of the power stage with 98.6% accuracy. Finally, this research addresses the system integration challenges such as synchronization and over-voltage protection. The fabricated self-synchronized prototype outputs up to 89% of the available power across 0.067%~7.9% coupling range. The output power (in percentage of available power) and coupling range are 1.3× and 13× higher than the comparable state of the arts.Ph.D