Time interleaved counter analog to digital converters

The work explores extending time interleaving in A/D converters, by applying a high-level of parallelism to one of the slowest and simplest types of data-converters, the counter ADC. The motivation for the work is to realise high-performance re-configurable A/D converters for use in multi-standard and multi-PHY communication receivers with signal bandwidths in the 10s to 100s of MHz. The counter ADC requires only a comparator, a ramp signal, and a digital counter, where the comparator compares the sampled input against all possible quantisation levels sequentially. This work explores arranging counter ADCs in large time-interleaved arrays, building a Time Interleaved Counter (TIC) ADC. The key to realising a TIC ADC is distributed sampling and a global multi-phase ramp generator realised with a novel figure-of-8 rotating resistor ring. Furthermore Counter ADCs allow for re-configurability between effective sampling rate and resolution due to their sequential comparison of reference levels in conversion. A prototype TIC ADC of 128-channels was fabricated and measured in 0.13μm CMOS technology, where the same block can be configured to operate as a 7-bit 1GS/s, 8-bit 500MS/s, or 9-bit 250MS/s dataconverter. The ADC achieves a sub 400fJ/step FOM in all modes of configuration

Design techniques for low-power multi-GS/s analog-to-digital converters

Ultra-high-speed (>10GS/s), medium-resolution (5~6bit), low-power (<50mW) analog-to-digital converter can find it application in the areas of digital oscilloscopes and next-generation serial link receivers. There are several challenges to enable a successful design, however. First, the time-interleaved architecture is required in order to achieve over 10GS/s sampling rate, with the trade-off of the number of the channels and the sampling rate in each channel. Phase misalignment and channel mismatch must be considered too. Second, timing accuracy, especially dynamic jitter of sampling clock becomes a major concern at ultra-high frequency, and certain techniques must be taken to address it. Finally, to achieve low power consumption, Flash architecture is not suitable to serve as the sub-ADC, and a low-power sub-ADC that can work at relatively high speed need to be designed. A single channel, asynchronous successive approximation (SA) ADC with improved feedback delay has been fabricated in 40nm CMOS. Compared with a conventional SA structure that employs a single quantizer controlled by a digital feedback logic loop, the proposed SA-ADC employs multiple quantizers for each conversion bit, clocked by an asynchronous ripple clock that is generated after each quantization. Hence, the sampling rate of the 6-bit ADC is limited only by the six delays of the Capacitive-DAC settling and each comparator’s quantization delay, as the digital logic delay is eliminated. Measurement results of the 40nm-CMOS SA-ADC achieves peak SNDR of 32.9dB at 1GS/s and 30.5dB at 1.25GS/s, consuming 5.28mW and 6.08mW respectively, leading to FoM of 148fJ/conversion-step and 178fJ/conversion-step, in a core area less than 170µm by 85µm. Based on the previous work of sub-ADC, a 12-GS/s 5-b 50-mW ADC is designed in 40nm CMOS with 8 time-interleaved channels of Flash-SA hybrid structure each running at 1.5GS/s. A modified bootstrapped switch is used in the track-and-hold circuit, introducing a global clock signal to synchronize the sampling instants of each individual channel, therefore improve the phase alignment and reduce distortion. The global clock is provided by a CML buffer which is injected by off-chip low-noise sine-wave signal, so that the RMS dynamic jitter is low for better ENOB performance. Measurement results show that the 12GS/s ADC can achieve a SNDR of 25.8dB with the input signal frequency around DC and 22.8dB around 2GHz, consuming 32.1mW, leading to FoM of 237.3fJ/conversion-step, in a core area less than 800µm by 500µm

Low-power adaptive control scheme using switching activity measurement method for reconfigurable analog-to-digital converters

Power consumption is a critical issue for portable devices. The ever-increasing demand for multimode wireless applications and the growing concerns towards power-aware green technology make dynamically reconfigurable hardware an attractive solution for overcoming the power issue. This is due to its advantages of flexibility, reusability, and adaptability. During the last decade, reconfigurable analog-to-digital converters (ReADCs) have been used to support multimode wireless applications. With the ability to adaptively scale the power consumption according to different operation modes, reconfigurable devices utilise the power supply efficiently. This can prolong battery life and reduce unnecessary heat emission to the environment. However, current adaptive mechanisms for ReADCs rely upon external control signals generated using digital signal processors (DSPs) in the baseband. This thesis aims to provide a single-chip solution for real-time and low-power ReADC implementations that can adaptively change the converter resolution according to signal variations without the need of the baseband processing. Specifically, the thesis focuses on the analysis, design and implementation of a low-power digital controller unit for ReADCs. In this study, the following two important reconfigurability issues are investigated: i) the detection mechanism for an adaptive implementation, and ii) the measure of power and area overheads that are introduced by the adaptive control modules. This thesis outlines four main achievements to address these issues. The first achievement is the development of the switching activity measurement (SWAM) method to detect different signal components based upon the observation of the output of an ADC. The second achievement is a proposed adaptive algorithm for ReADCs to dynamically adjust the resolution depending upon the variations in the input signal. The third achievement is an ASIC implementation of the adaptive control module for ReADCs. The module achieves low reconfiguration overheads in terms of area and power compared with the main analog part of a ReADC. The fourth achievement is the development of a low-power noise detection module using a conventional ADC for signal improvement. Taken together, the findings from this study demonstrate the potential use of switching activity information of an ADC to adaptively control the circuits, and simultaneously expanding the functionality of the ADC in electronic systems

Radiation Tolerant Electronics, Volume II

Research on radiation tolerant electronics has increased rapidly over the last few years, resulting in many interesting approaches to model radiation effects and design radiation hardened integrated circuits and embedded systems. This research is strongly driven by the growing need for radiation hardened electronics for space applications, high-energy physics experiments such as those on the large hadron collider at CERN, and many terrestrial nuclear applications, including nuclear energy and safety management. With the progressive scaling of integrated circuit technologies and the growing complexity of electronic systems, their ionizing radiation susceptibility has raised many exciting challenges, which are expected to drive research in the coming decade.After the success of the first Special Issue on Radiation Tolerant Electronics, the current Special Issue features thirteen articles highlighting recent breakthroughs in radiation tolerant integrated circuit design, fault tolerance in FPGAs, radiation effects in semiconductor materials and advanced IC technologies and modelling of radiation effects

Design of clock and data recovery circuits for energy-efficient short-reach optical transceivers

Nowadays, the increasing demand for cloud based computing and social media services mandates higher throughput (at least 56 Gb/s per data lane with 400 Gb/s total capacity 1) for short reach optical links (with the reach typically less than 2 km) inside data centres. The immediate consequences are the huge and power hungry data centers. To address these issues the intra-data-center connectivity by means of optical links needs continuous upgrading. In recent years, the trend in the industry has shifted toward the use of more complex modulation formats like PAM4 due to its spectral efficiency over the traditional NRZ. Another advantage is the reduced number of channels count which is more cost-effective considering the required area and the I/O density. However employing PAM4 results in more complex transceivers circuitry due to the presence of multilevel transitions and reduced noise budget. In addition, providing higher speed while accommodating the stringent requirements of higher density and energy efficiency (< 5 pJ/bit), makes the design of the optical links more challenging and requires innovative design techniques both at the system and circuit level. This work presents the design of a Clock and Data Recovery Circuit (CDR) as one of the key building blocks for the transceiver modules used in such fibreoptic links. Capable of working with PAM4 signalling format, the new proposed CDR architecture targets data rates of 50−56 Gb/s while achieving the required energy efficiency (< 5 pJ/bit). At the system level, the design proposes a new PAM4 PD which provides a better trade-off in terms of bandwidth and systematic jitter generation in the CDR. By using a digital loop controller (DLC), the CDR gains considerable area reduction with flexibility to adjust the loop dynamics. At the circuit level it focuses on applying different circuit techniques to mitigate the circuit imperfections. It presents a wideband analog front end (AFE), suitable for a 56 Gb/s, 28-Gbaud PAM-4 signal, by using an 8x interleaved, master/ slave based sample and hold circuit. In addition, the AFE is equipped with a calibration scheme which corrects the errors associated with the sampling channels’ offset voltage and gain mismatches. The presented digital to phase converter (DPC) features a modified phase interpolator (PI), a new quadrature phase corrector (QPC) and multi-phase output with de-skewing capabilities.The DPC (as a standalone block) and the CDR (as the main focus of this work) were fabricated in 65-nm CMOS technology. Based on the measurements, the DPC achieves DNL/INL of 0.7/6 LSB respectively while consuming 40.5 mW power from 1.05 V supply. Although the CDR was not fully operational with the PAM4 input, the results from 25-Gbaud PAM2 (NRZ) test setup were used to estimate the performance. Under this scenario, the 1-UI JTOL bandwidth was measured to be 2 MHz with BER threshold of 10−4. The chip consumes 236 mW of power while operating on 1 − 1.2 V supply range achieving an energyefficiency of 4.27 pJ/bit

MIMO Systems

In recent years, it was realized that the MIMO communication systems seems to be inevitable in accelerated evolution of high data rates applications due to their potential to dramatically increase the spectral efficiency and simultaneously sending individual information to the corresponding users in wireless systems. This book, intends to provide highlights of the current research topics in the field of MIMO system, to offer a snapshot of the recent advances and major issues faced today by the researchers in the MIMO related areas. The book is written by specialists working in universities and research centers all over the world to cover the fundamental principles and main advanced topics on high data rates wireless communications systems over MIMO channels. Moreover, the book has the advantage of providing a collection of applications that are completely independent and self-contained; thus, the interested reader can choose any chapter and skip to another without losing continuity

MediaSync: Handbook on Multimedia Synchronization

This book provides an approachable overview of the most recent advances in the fascinating field of media synchronization (mediasync), gathering contributions from the most representative and influential experts. Understanding the challenges of this field in the current multi-sensory, multi-device, and multi-protocol world is not an easy task. The book revisits the foundations of mediasync, including theoretical frameworks and models, highlights ongoing research efforts, like hybrid broadband broadcast (HBB) delivery and users' perception modeling (i.e., Quality of Experience or QoE), and paves the way for the future (e.g., towards the deployment of multi-sensory and ultra-realistic experiences). Although many advances around mediasync have been devised and deployed, this area of research is getting renewed attention to overcome remaining challenges in the next-generation (heterogeneous and ubiquitous) media ecosystem. Given the significant advances in this research area, its current relevance and the multiple disciplines it involves, the availability of a reference book on mediasync becomes necessary. This book fills the gap in this context. In particular, it addresses key aspects and reviews the most relevant contributions within the mediasync research space, from different perspectives. Mediasync: Handbook on Multimedia Synchronization is the perfect companion for scholars and practitioners that want to acquire strong knowledge about this research area, and also approach the challenges behind ensuring the best mediated experiences, by providing the adequate synchronization between the media elements that constitute these experiences

Radio Communications

In the last decades the restless evolution of information and communication technologies (ICT) brought to a deep transformation of our habits. The growth of the Internet and the advances in hardware and software implementations modified our way to communicate and to share information. In this book, an overview of the major issues faced today by researchers in the field of radio communications is given through 35 high quality chapters written by specialists working in universities and research centers all over the world. Various aspects will be deeply discussed: channel modeling, beamforming, multiple antennas, cooperative networks, opportunistic scheduling, advanced admission control, handover management, systems performance assessment, routing issues in mobility conditions, localization, web security. Advanced techniques for the radio resource management will be discussed both in single and multiple radio technologies; either in infrastructure, mesh or ad hoc networks

3rd International Workshop on Instrumentation for Planetary Missions : October 24–27, 2016, Pasadena, California

The purpose of this workshop is to provide a forum for collaboration, exchange of ideas and information, and discussions in the area of the instruments, subsystems, and other payload-related technologies needed to address planetary science questions. The agenda will compose a broad survey of the current state-of-the-art and emerging capabilities in instrumentation available for future planetary missions.Universities Space Research Association (USRA); Lunar and Planetary Institute (LPI); Jet Propulsion Laboratory (JPL)Conveners: Sabrina Feldman, Jet Propulsion Laboratory, David Beaty, Jet Propulsion Laboratory ; Science Organizing Committee: Carlton Allen, Johnson Space Center (retired) [and 12 others