상보적인 스위치 동작을 이용한 주입 고정 위상 동기화 루프의 설계에 관한 연구

학위논문 (박사)-- 서울대학교 대학원 : 공과대학 전기·컴퓨터공학부, 2019. 2. 정덕균.높은 속도의 어플리케이션의 수요 증가로 인하여 좋은 성능의 높은 주파수 생성기의 요구가 증가하고 있다. 이에 따라 주입 고정 발진기를 이용한 연구가 활발히 진행되고 있다. 본 논문에서는 상보적인 스위치 동작을 이용한 주입 고정 위상 동기화 루프 (subharmonically injection-locked phase-locked loop) 의 설계에 관한 연구에 대해 논의한다. 설계의 간소화를 위하여 상보적인 스위치 동작을 이용한 주입방법 (complementary switched injection) 을 제안하고 서브샘플링 위상 검출기 (sub-sampling phase detector) 를 사용하였다. 스위치 동작을 이용한 주입방법은 펄스발생기를 대체함으로써 지연시간이 발생하지 않도록 하였고 주입 클락의 듀얼 엣지에서 주입이 가능하여 싱글 엣지 주입보다 성능이 좋아진다는 장점이 있다. 서브샘플링 위상 검출기 또한 위상 동기화 루프의 피드백 경로에서 지연시간이 발생하지 않기 때문에 추가적인 주입 타이밍 루프가 없어도 주입 경로와 위상 동기화 루프에서 위상이 조정될 때 서로간의 불일치가 발생하지 않는다. 또한, 제안된 구조의 주입 고정 위상 동기화 루프는 전압이나 온도에 덜 민감하게 설계되었다. 제안한 스위치 동작을 이용한 주입방법을 전하 이동을 기반으로 분석하였고 잘못된 타이밍에 주입이 되었을 때 레퍼런스 스퍼에 대한 성능을 비교하였다. 65-nm CMOS 공정을 이용하여 만들어진 칩은 5 GHz 에서 15.4 mW의 파워 소모와 0.06 mm2 의 면적을 가진다. 또한, 동작영역은 2.5 GHz 에서 5.6 GHz 를 가지며5 GHz 에서168 fs rms지터를 갖는다.As increasing demands for high speeds link systems and requiring design challenges in clock generation, the injection locking technique is widely used in clock multiplication. However, it is still difficult to design high performance of injection-locked clock multiplier (ILCM) because of its narrow lock-in range. In this thesis, a low-phase-noise subharmonically injection-locked sub-sampling all-digital phase-locked loop (ILPLL) is proposed using a dual-edge complementary switched injection (CSI) technique and sub-sampling bang-bang phase detector (SSBBPD) without an injection pulse generation and injection timing calibration circuitry. With the proposed IL-DCO and SSBBPD, the phase alignment mismatch between the PLL loop and injection path does not occurs and makes it possible to exhibit a simplified architecture. Because the CSI technique exploits dual-edge injection, the performance impact of dual-edge injection when inaccurate injection time occurs is analyzed. Also, the CSI technique is analyzed with base on the charge transfer and derives the realignment factor of the injection. With the CSI technique and the direct connection of the digitally controlled oscillator (DCO) clock to the SSBBPD, the timing mismatch between the PLL loop and injection path becomes less sensitive to voltage and temperature drift. The proposed ILPLL prototype is fabricated in a 65-nm CMOS process and achieves a 168-fs integrated RMS jitter over 1 kHz to 40 MHz at a 5-GHz output frequency with 156.25-MHz reference clock while consuming 15.4 mW with an active area of 0.06 mm2.ABSTRACT I CONTENTS III LIST OF FIGURES V LIST OF TABLES X CHAPTER 1 INTRODUCTION 11 1.1 MOTIVATION 11 1.2 THESIS ORGANIZATION 13 CHAPTER 2 BASIC INJECTION-LOCKED CLOCK MULTIPLIER 14 2.1 INJECTION-LOCKED OSCILLATOR (ILO) 14 2.1.1 INTRODUCTION 14 2.1.2 PHASE DOMAIN RESPONSE (PDR) ANALYSIS 21 2.1.3 NOISE FILTERING BANDWIDTH 30 2.2 INJECTION-LOCKED CLOCK MULTIPLIER 33 2.2.1 OVERVIEW 33 2.2.2 PRIOR ARTS 37 2.2.2.1 PLL-BASED ILCM 37 2.2.2.2 REPLICA-BASED ILCM 39 2.2.2.3 REAL-TIME FTL-BASED ILCM 41 2.3 CONCEPT OF THE PROPOSED ILCM 43 CHAPTER 3 DESIGN OF SUBHARMONICALLY ILPLL 44 3.1 OVERVIEW 44 3.2 PROPOSED ARCHITECTURE 45 3.2.1 OVERALL ARCHITECTURE 45 3.2.2 DUAL-EDGE COMPLEMENTARY SWITCHED INJECTION 47 3.3 ANALYSIS OF THE INJECTION-LOCKED PLL 55 3.3.1 NOISE ANALYSIS 55 3.3.2 PHASE MARGIN ANALYSIS 60 3.3.3 SPUR ANALYSIS 64 3.4 CIRCUIT IMPLEMENTATION 75 3.4.1 DIGITALLY CONTROLLED ILO 75 3.4.2 SSBBPD AND FRONT-END 76 3.4.3 FREQUENCY DETECTOR 82 CHAPTER 4 MEASUREMENT 86 CHAPTER 5 CONCLUSION 97 APPENDIX A 98 BIBLIOGRAPHY 105 초 록 113Docto

Spur Reduction Techniques for Phase-Locked Loops Exploiting A Sub-Sampling Phase Detector

This paper presents phase-locked loop (PLL) reference-spur reduction design techniques exploiting a sub-sampling phase detector (SSPD) (which is also referred to as a sampling phase detector). The VCO is sampled by the reference clock without using a frequency divider and an amplitude controlled charge pump is used which is inherently insensitive to mismatch. The main remaining source of the VCO reference spur is the periodic disturbance of the VCO by the sampling at the reference frequency. The underlying VCO sampling spur mechanisms are analyzed and their effect is minimized by using dummy samplers and isolation buffers. A duty-cycle-controlled reference buffer and delay-locked loop (DLL) tuning are proposed to further reduce the worst case spur level. To demonstrate the effectiveness of the\ud proposed spur reduction techniques, a 2.21 GHz PLL is designed and fabricated in 0.18 m CMOS technology. While using a high loop-bandwidth-to-reference-frequency ratio of 1/20, the reference spur measured from 20 chips is 80 dBc. The PLL consumes 3.8 mW while the in-band phase noise is 121 dBc/Hz at 200 kHz and the output jitter integrated from 10 kHz to 100 MHz is 0.3 ps rms

PVT-Robust Ultra-Low-Jitter Clock Multipliers Using an Injection-Locking Technique

Department of Electrical EngineeringThis thesis presents process-voltage-temperature (PVT)-robust ultra-low-jitter clock multipliers using an injection-locking technique. First, an injection-locked clock multiplier (ILCM) using a two-phase PVT-calibrator is proposed. The proposed PVT-calibration technique is based on the dual-loop architecture which consists of a main-voltage-controlled oscillator (VCO) and a replica-VCO. While the main-VCO is injection-locked and generates the precise target frequency, the real-time frequency variation of the replica-VCO can be monitored by the PVT-calibrator which adjusts the control voltage shared by the two identical VCOs. Using the two-phase calibration technique, the tradeoff between the calibration resolution and the lock time was removed. The proposed ILCM, fabricated in the 65-nm CMOS process, generated five different reference frequencies, i.e., 19.2, 28.8, 48.0, 57.6, and 96.0 MHz with a 19.2 MHz external clock. When injection-locked, the integrated jitter from 1 kHz to 10 MHz of the 96-MHz signal was 1.69 ps. The proposed PVT-calibrator restricted the phase noise degradation over the temperature range of 30 to 80 ??C to less than 0.5 dB. Second, a fractional-resolution ILCM using a delay-locked-loop (DLL)-based PVT-calibrator is proposed. In this architecture, the ring-type VCO and the voltage-controlled delay line (VCDL) of the DLL consist of identical delay cells, and they share the same control voltage. Thus, by changing the ratio between the numbers of stages of the VCDL and the VCO, the frequency of the VCO can be calibrated at a target frequency, a non-integer times the reference frequency. The proposed ILCM, designed in the 65-nm CMOS process, generated output frequencies that range from 1.2 to 2.0 GHz with a frequency resolution of 40 MHz with a 400-MHz reference clock. When injection-locked, the integrated jitter from 1 kHz to 40 MHz of the 1.6-GHz signal was 440 fs. The proposed DLL-based PVT-calibrator restricted the degradations of phase noise and jitter over the temperature and the supply variations to less than 0.7 dB and 20%, respectively. Both architectures presented in this thesis can overcome real-time frequency drifts as well as static process variationsthus, excellent jitter performance can be sustained during any environmental variations.ope

Injection Locked Oscillator for Radiometer

The main goal of this project was to design an injection locked oscillator (ILO) with free-running frequency of 70 GHz, and with locking capability to the third and the fifth harmonics of the reference signal upon injection. The circuit was realized using the silicon-germanium (SiGe) bipolar-complementary metal-oxide-semiconductor (BiCMOS) technology and the locking condition were verified after simulating the resistor-capacitor (RC) extracted netlist of the layout. The cadence virtuoso toolkit was used for the design process and the simulation purpose. The locking phenomenon, quasi-lock and fast-beat mode, lock range upon different injection power and phase noise characteristics of the ILO upon subharmonic injection were studied. The ILO was implemented using the direct (parallel) injection topology. The designed ILO circuit consists of two main components; conventional cross-coupled oscillator with oscillation frequency of 71 GHz and harmonic generator that injects the harmonics of the reference signal into the oscillator. The nonlinearity of the transistor was studied under different biasing conditions and the optimal bias point of 0.83 V was chosen that provided the maximum frequency conversion gain. The power consumed by the core oscillator is 2.64 mW and 3.4 mW by the harmonic generator under the supply voltage of 1.2 V, making the total power consumption of 6.04 mW as a whole by the ILO. The ILO achieved the locking range (LR) of 7.9% for the fifth harmonics injection and 1.22% for the third harmonics injection of the reference signal with input injection power of 0 dBm. The oscillator even achieved 0.32% LR for the seventh harmonics injection with the injection power of 0 dBm. The corresponding frequency ranges are 18.9-24.5 GHz, 13.29-14.16 GHz, 9.8-10.03 GHz for the third, fifth and the seventh harmonics respectively

고속 시리얼 링크를 위한 고리 발진기를 기반으로 하는 주파수 합성기

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022. 8. 정덕균.In this dissertation, major concerns in the clocking of modern serial links are discussed. As sub-rate, multi-standard architectures are becoming predominant, the conventional clocking methodology seems to necessitate innovation in terms of low-cost implementation. Frequency synthesis with active, inductor-less oscillators replacing LC counterparts are reviewed, and solutions for two major drawbacks are proposed. Each solution is verified by prototype chip design, giving a possibility that the inductor-less oscillator may become a proper candidate for future high-speed serial links. To mitigate the high flicker noise of a high-frequency ring oscillator (RO), a reference multiplication technique that effectively extends the bandwidth of the following all-digital phase-locked loop (ADPLL) is proposed. The technique avoids any jitter accumulation, generating a clean mid-frequency clock, overall achieving high jitter performance in conjunction with the ADPLL. Timing constraint for the proper reference multiplication is first analyzed to determine the calibration points that may correct the existent phase errors. The weight for each calibration point is updated by the proposed a priori probability-based least-mean-square (LMS) algorithm. To minimize the time required for the calibration, each gain for the weight update is adaptively varied by deducing a posteriori which error source dominates the others. The prototype chip is fabricated in a 40-nm CMOS technology, and its measurement results verify the low-jitter, high-frequency clock generation with fast calibration settling. The presented work achieves an rms jitter of 177/223 fs at 8/16-GHz output, consuming 12.1/17-mW power. As the second embodiment, an RO-based ADPLL with an analog technique that addresses the high supply sensitivity of the RO is presented. Unlike prior arts, the circuit for the proposed technique does not extort the RO voltage headroom, allowing high-frequency oscillation. Further, the performance given from the technique is robust over process, voltage, and temperature (PVT) variations, avoiding the use of additional calibration hardware. Lastly, a comprehensive analysis of phase noise contribution is conducted for the overall ADPLL, followed by circuit optimizations, to retain the low-jitter output. Implemented in a 40-nm CMOS technology, the frequency synthesizer achieves an rms jitter of 289 fs at 8 GHz output without any injected supply noise. Under a 20-mVrms white supply noise, the ADPLL suppresses supply-noise-induced jitter by -23.8 dB.본 논문은 현대 시리얼 링크의 클락킹에 관여되는 주요한 문제들에 대하여 기술한다. 준속도, 다중 표준 구조들이 채택되고 있는 추세에 따라, 기존의 클라킹 방법은 낮은 비용의 구현의 관점에서 새로운 혁신을 필요로 한다. LC 공진기를 대신하여 능동 소자 발진기를 사용한 주파수 합성에 대하여 알아보고, 이에 발생하는 두가지 주요 문제점과 각각에 대한 해결 방안을 탐색한다. 각 제안 방법을 프로토타입 칩을 통해 그 효용성을 검증하고, 이어서 능동 소자 발진기가 미래의 고속 시리얼 링크의 클락킹에 사용될 가능성에 대해 검토한다. 첫번째 시연으로써, 고주파 고리 발진기의 높은 플리커 잡음을 완화시키기 위해 기준 신호를 배수화하여 뒷단의 위상 고정 루프의 대역폭을 효과적으로 극대화 시키는 회로 기술을 제안한다. 본 기술은 지터를 누적 시키지 않으며 따라서 깨끗한 중간 주파수 클락을 생성시켜 위상 고정 루프와 함께 높은 성능의 고주파 클락을 합성한다. 기준 신호를 성공적으로 배수화하기 위한 타이밍 조건들을 먼저 분석하여 타이밍 오류를 제거하기 위한 방법론을 파악한다. 각 교정 중량은 연역적 확률을 기반으로한 LMS 알고리즘을 통해 갱신되도록 설계된다. 교정에 필요한 시간을 최소화 하기 위하여, 각 교정 이득은 타이밍 오류 근원들의 크기를 귀납적으로 추론한 값을 바탕으로 지속적으로 제어된다. 40-nm CMOS 공정으로 구현된 프로토타입 칩의 측정을 통해 저소음, 고주파 클락을 빠른 교정 시간안에 합성해 냄을 확인하였다. 이는 177/223 fs의 rms 지터를 가지는 8/16 GHz의 클락을 출력한다. 두번째 시연으로써, 고리 발진기의 높은 전원 노이즈 의존성을 완화시키는 기술이 포함된 주파수 합성기가 설계되었다. 이는 고리 발진기의 전압 헤드룸을 보존함으로서 고주파 발진을 가능하게 한다. 나아가, 전원 노이즈 감소 성능은 공정, 전압, 온도 변동에 대하여 민감하지 않으며, 따라서 추가적인 교정 회로를 필요로 하지 않는다. 마지막으로, 위상 노이즈에 대한 포괄적 분석과 회로 최적화를 통하여 주파수 합성기의 저잡음 출력을 방해하지 않는 방법을 고안하였다. 해당 프로토타입 칩은 40-nm CMOS 공정으로 구현되었으며, 전원 노이즈가 인가되지 않은 상태에서 289 fs의 rms 지터를 가지는 8 GHz의 클락을 출력한다. 또한, 20 mVrms의 전원 노이즈가 인가되었을 때에 유도되는 지터의 양을 -23.8 dB 만큼 줄이는 것을 확인하였다.1 Introduction 1 1.1 Motivation 3 1.1.1 Clocking in High-Speed Serial Links 4 1.1.2 Multi-Phase, High-Frequency Clock Conversion 8 1.2 Dissertation Objectives 10 2 RO-Based High-Frequency Synthesis 12 2.1 Phase-Locked Loop Fundamentals 12 2.2 Toward All-Digital Regime 15 2.3 RO Design Challenges 21 2.3.1 Oscillator Phase Noise 21 2.3.2 Challenge 1: High Flicker Noise 23 2.3.3 Challenge 2: High Supply Noise Sensitivity 26 3 Filtering RO Noise 28 3.1 Introduction 28 3.2 Proposed Reference Octupler 34 3.2.1 Delay Constraint 34 3.2.2 Phase Error Calibration 38 3.2.3 Circuit Implementation 51 3.3 IL-ADPLL Implementation 55 3.4 Measurement Results 59 3.5 Summary 63 4 RO Supply Noise Compensation 69 4.1 Introduction 69 4.2 Proposed Analog Closed Loop for Supply Noise Compensation 72 4.2.1 Circuit Implementation 73 4.2.2 Frequency-Domain Analysis 76 4.2.3 Circuit Optimization 81 4.3 ADPLL Implementation 87 4.4 Measurement Results 90 4.5 Summary 98 5 Conclusions 99 A Notes on the 8REF 102 B Notes on the ACSC 105박

Architectures and Circuits Leveraging Injection-Locked Oscillators for Ultra-Low Voltage Clock Synthesis and Reference-less Receivers for Dense Chip-to-Chip Communications

High performance computing is critical for the needs of scientific discovery and economic competitiveness. An extreme-scale computing system at 1000x the performance of today’s petaflop machines will exhibit massive parallelism on multiple vertical fronts, from thousands of computational units on a single processor to thousands of processors in a single data center. To facilitate such a massively-parallel extreme-scale computing, a key challenge is power. The challenge is not power associated with base computation but rather the problem of transporting data from one chip to another at high enough rates. This thesis presents architectures and techniques to achieve low power and area footprint while achieving high data rates in a dense very-short reach (VSR) chip-to-chip (C2C) communication network. High-speed serial communication operating at ultra-low supplies improves the energy-efficiency and lowers the power envelop of a system doing an exaflop of loops. One focus area of this thesis is clock synthesis for such energy-efficient interconnect applications operating at high speeds and ultra-low supplies. A sub-integer clockfrequency synthesizer is presented that incorporates a multi-phase injection-locked ring-oscillator-based prescaler for operation at an ultra-low supply voltage of 0.5V, phase-switching based programmable division for sub-integer clock-frequency synthesis, and automatic calibration to ensure injection lock. A record speed of 9GHz has been demonstrated at 0.5V in 45nm SOI CMOS. It consumes 3.5mW of power at 9.12GHz and 0.052 of area, while showing an output phase noise of -100dBc/Hz at 1MHz offset and RMS jitter of 325fs; it achieves a net of -186.5 in a 45-nm SOI CMOS process. This thesis also describes a receiver with a reference-less clocking architecture for high-density VSR-C2C links. This architecture simplifies clock-tree planning in dense extreme-scaling computing environments and has high-bandwidth CDR to enable SSC for suppressing EMI and to mitigate TX jitter requirements. It features clock-less DFE and a high-bandwidth CDR based on master-slave ILOs for phase generation/rotation. The RX is implemented in 14nm CMOS and characterized at 19Gb/s. It is 1.5x faster that previous reference-less embedded-oscillator based designs with greater than 100MHz jitter tolerance bandwidth and recovers error-free data over VSR-C2C channels. It achieves a power-efficiency of 2.9pJ/b while recovering error-free data (BER 200MHz and the INL of the ILO-based phase-rotator (32- Steps/UI) is <1-LSB. Lastly, this thesis develops a time-domain delay-based modeling of injection locking to describe injection-locking phenomena in nonharmonic oscillators. The model is used to predict the locking bandwidth, and the locking dynamics of the locked oscillator. The model predictions are verified against simulations and measurements of a four-stage differential ring oscillator. The model is further used to predict the injection-locking behavior of a single-ended CMOS inverter based ring oscillator, the lock range of a multi-phase injection-locked ring-oscillator-based prescaler, as well as the dynamics of tracking injection phase perturbations in injection-locked masterslave oscillators; demonstrating its versatility in application to any nonharmonic oscillator

Self-Calibrated, Low-Jitter and Low-Reference-Spur Injection-Locked Clock Multipliers

Department of Electrical EngineeringThis dissertation focuses primarily on the design of calibrators for the injection-locked clock multiplier (ILCM). ILCMs have advantage to achieve an excellent jitter performance at low cost, in terms of area and power consumption. The wide loop bandwidth (BW) of the injection technique could reject the noise of voltage-controlled oscillator (VCO), making it thus suitable for the rejection of poor noise of a ring-VCO and a high frequency LC-VCO. However, it is difficult to use without calibrators because of its sensitiveness in process-voltage-temperature (PVT) variations. In Chapter 2, conventional frequency calibrators are introduced and discussed. This dissertation introduces two types of calibrators for low-power high-frequency LC-VCO-based ILFMs in Chapter 3 and Chapter 4 and high-performance ring-VCO-based ILCM in Chapter 5. First, Chapter 3 presents a low power and compact area LC-tank-based frequency multiplier. In the proposed architecture, the input signals have a pulsed waveform that involves many high-order harmonics. Using an LC-tank that amplifies only the target harmonic component, while suppressing others, the output signal at the target frequency can be obtained. Since the core current flows for a very short duration, due to the pulsed input signals, the average power consumption can be dramatically reduced. Effective removal of spurious tones due to the damping of the signal is achieved using a limiting amplifier. In this work, a prototype frequency tripler using the proposed architecture was designed in a 65 nm CMOS process. The power consumption was 950 ??W, and the active area was 0.08 mm2. At a 3.12 GHz frequency, the phase noise degradation with respect to the theoretical bound was less than 0.5 dB. Second, Chapter 4 presents an ultra-low-phase-noise ILFM for millimeter wave (mm-wave) fifth-generation (5G) transceivers. Using an ultra-low-power frequency-tracking loop (FTL), the proposed ILFM is able to correct the frequency drifts of the quadrature voltage-controlled oscillator of the ILFM in a real-time fashion. Since the FTL is monitoring the averages of phase deviations rather than detecting or sampling the instantaneous values, it requires only 600??W to continue to calibrate the ILFM that generates an mm-wave signal with an output frequency from 27 to 30 GHz. The proposed ILFM was fabricated in a 65-nm CMOS process. The 10-MHz phase noise of the 29.25-GHz output signal was ???129.7 dBc/Hz, and its variations across temperatures and supply voltages were less than 2 dB. The integrated phase noise from 1 kHz to 100 MHz and the rms jitter were???39.1 dBc and 86 fs, respectively. Third, Chapter 5 presents a low-jitter, low-reference-spur ring voltage-controlled oscillator (ring VCO)-based ILCM. Since the proposed triple-point frequency/phase/slope calibrator (TP-FPSC) can accurately remove the three root causes of the frequency errors of ILCMs (i.e., frequency drift, phase offset, and slope modulation), the ILCM of this work is able to achieve a low-level reference spur. In addition, the calibrating loop for the frequency drift of the TP-FPSC offers an additional suppression to the in-band phase noise of the output signal. This capability of the TP-FPSC and the naturally wide bandwidth of the injection-locking mechanism allows the ILCM to achieve a very low RMS jitter. The ILCM was fabricated in a 65-nm CMOS technology. The measured reference spur and RMS jitter were ???72 dBc and 140 fs, respectively, both of which are the best among the state-of-the-art ILCMs. The active silicon area was 0.055 mm2, and the power consumption was 11.0 mW.clos

A Low-Power BFSK/OOK Transmitter for Wireless Sensors

In recent years, significant improvements in semiconductor technology have allowed consistent development of wireless chipsets in terms of functionality and form factor. This has opened up a broad range of applications for implantable wireless sensors and telemetry devices in multiple categories, such as military, industrial, and medical uses. The nature of these applications often requires the wireless sensors to be low-weight and energy-efficient to achieve long battery life. Among the various functions of these sensors, the communication block, used to transmit the gathered data, is typically the most power-hungry block. In typical wireless sensor networks, transmission range is below 10 meters and required radiated power is below 1 milliwatt. In such cases, power consumption of the frequency-synthesis circuits prior to the power amplifier of the transmitter becomes significant. Reducing this power consumption is currently the focus of various research endeavors. A popular method of achieving this goal is using a direct-modulation transmitter where the generated carrier is directly modulated with baseband data using simple modulation schemes. Among the different variations of direct-modulation transmitters, transmitters using unlocked digitally-controlled oscillators and transmitters with injection or resonator-locked oscillators are widely investigated because of their simple structure. These transmitters can achieve low-power and stable operation either with the help of recalibration or by sacrificing tuning capability. In contrast, phase-locked-loop-based (PLL) transmitters are less researched. The PLL uses a feedback loop to lock the carrier to a reference frequency with a programmable ratio and thus achieves good frequency stability and convenient tunability. This work focuses on PLL-based transmitters. The initial goal of this work is to reduce the power consumption of the oscillator and frequency divider, the two most power-consuming blocks in a PLL. Novel topologies for these two blocks are proposed which achieve ultra-low-power operation. Along with measured performance, mathematical analysis to derive rule-of-thumb design approaches are presented. Finally, the full transmitter is implemented using these blocks in a 130 nanometer CMOS process and is successfully tested for low-power operation

A 3.2 GHz Injection-Locked Ring Oscillator-Based Phase-Locked-Loop for Clock Recovery

An injection-locked ring oscillator-based phase-locked-loop targeting clock recovery for space application at 3.2 GHz is presented here. Most clock recovery circuits need a very low phase noise and jitter performance and are thus based on LC-type oscillators. These excellent performances come at the expense of a very poor integration density. To alleviate this issue, this work introduces an injection-locked ring oscillator-based PLL circuit. The combination of the injection-locking process with the use of ring oscillators allows for the benefit of excellent jitter performance while presenting an extremely low surface area due to an architecture without any inductor. The injection locking principle is addressed, and evidence of its phase noise and jitter improvements are confirmed through measurement results. Indeed, phase noise and jitter enhancements up to 43 dB and 23.3 mUI, respectively, were measured. As intended, this work shows the best integration density compared to recent similar state-of-the-art studies. The whole architecture measures 0.1 mm2 while consuming 34.6 mW in a low-cost 180 nm CMOS technology

Digital enhancement techniques for fractional-N frequency synthesizers

Meeting the demand for unprecedented connectivity in the era of internet-of-things (IoT) requires extremely energy efficient operation of IoT nodes to extend battery life. Managing the data traffic generated by trillions of such nodes also puts severe energy constraints on the data centers. Clock generators that are essential elements in these systems consume significant power and therefore must be optimized for low power and high performance. The focus of this thesis is on improving the energy efficiency of frequency synthesizers and clocking modules by exploring design techniques at both the architectural and circuit levels. In the first part of this work, a digital fractional-N phase locked loop (FNPLL) that employs a high resolution time-to-digital converter (TDC) and a truly ΔΣ fractional divider to achieve low in-band noise with a wide bandwidth is presented. The fractional divider employs a digital-to-time converter (DTC) to cancel out ΔΣ quantization noise in time domain, thus alleviating TDC dynamic range requirements. The proposed digital architecture adopts a narrow range low-power time-amplifier based TDC (TA-TDC) to achieve sub 1ps resolution. Fabricated in 65nm CMOS process, the prototype PLL achieves better than -106dBc/Hz in-band noise and 3MHz PLL bandwidth at 4.5GHz output frequency using 50MHz reference. The PLL achieves excellent jitter performance of 490fsrms, while consumes only 3.7mW. This translates to the best reported jitter-power figure-of-merit (FoM) of -240.5dB among previously reported FNPLLs. Phase noise performance of ring oscillator based digital FNPLLs is severely compromised by conflicting bandwidth requirements to simultaneously suppress oscillator phase and quantization noise introduced by the TDC, ΔΣ fractional divider, and digital-to-analog converter (DAC). As a consequence, their FoM that quantifies the power-jitter tradeoff is at least 25dB worse than their LC-oscillator based FNPLL counterparts. In the second part of this thesis, we seek to close this performance gap by extending PLL bandwidth using quantization noise cancellation techniques and by employing a dual-path digital loop filter to suppress the detrimental impact of DAC quantization noise. A prototype was implemented in a 65nm CMOS process operating over a wide frequency range of 2.0GHz-5.5GHz using a modified extended range multi-modulus divider with seamless switching. The proposed digital FNPLL achieves 1.9psrms integrated jitter while consuming only 4mW at 5GHz output. The measured in-band phase noise is better than -96 dBc/Hz at 1MHz offset. The proposed FNPLL achieves wide bandwidth up to 6MHz using a 50 MHz reference and its FoM is -228.5dB, which is at about 20dB better than previously reported ring-based digital FNPLLs. In the third part, we propose a new multi-output clock generator architecture using open loop fractional dividers for system-on-chip (SoC) platforms. Modern multi-core processors use per core clocking, where each core runs at its own speed. The core frequency can be changed dynamically to optimize for performance or power dissipation using a dynamic frequency scaling (DFS) technique. Fast frequency switching is highly desirable as long as it does not interrupt code execution; therefore it requires smooth frequency transitions with no undershoots. The second main requirement in processor clocking is the capability of spread spectrum frequency modulation. By spreading the clock energy across a wide bandwidth, the electromagnetic interference (EMI) is dramatically reduced. A conventional PLL clock generation approach suffers from a slow frequency settling and limited spread spectrum modulation capabilities. The proposed open loop fractional divider architecture overcomes the bandwidth limitation in fractional-N PLLs. The fractional divider switches the output frequency instantaneously and provides an excellent spread spectrum performance, where precise and programmable modulation depth and frequency can be applied to satisfy different EMI requirements. The fractional divider has unlimited modulation bandwidth resulting in spread spectrum modulation with no filtering, unlike fractional-N PLL; consequently it achieves higher EMI reduction. A prototype fractional divider was implemented in a 65nm CMOS process, where the measured peak-to-peak jitter is less than 27ps over a wide frequency range from 20MHz to 1GHz. The total power consumption is about 3.2mW for 1GHz output frequency. The all-digital implementation of the divider occupies the smallest area of 0.017mm2 compared to state-of-the-art designs. As the data rate of serial links goes higher, the jitter requirements of the clock generator become more stringent. Improving the jitter performance of conventional PLLs to less than (200fsrms) always comes with a large power penalty (tens of mWs). This is due to the PLL coupled noise bandwidth trade-off, which imposes stringent noise requirements on the oscillator and/or loop components. Alternatively, an injection-locked clock multiplier (ILCM) provides many advantages in terms of phase noise, power, and area compared to classical PLLs, but they suffer from a narrow lock-in range and a high sensitivity to PVT variations especially at a large multiplication factor (N). In the fourth part of this thesis, a low-jitter, low-power LC-based ILCM with a digital frequency-tracking loop (FTL) is presented. The proposed FTL relies on a new pulse gating technique to continuously tune the oscillator's free-running frequency. The FTL ensures robust operation across PVT variations and resolves the race condition existing in injection locked PLLs by decoupling frequency tuning from the injection path. As a result, the phase locking condition is only determined by the injection path. This work also introduces an accurate theoretical large-signal analysis for phase domain response (PDR) of injection locked oscillators (ILOs). The proposed PDR analysis captures the asymmetric nature of ILO's lock-in range, and the impact of frequency error on injection strength and phase noise performance. The proposed architecture and analysis are demonstrated by a prototype fabricated in 65 nm CMOS process with active area of 0.25mm2. The prototype ILCM multiplies the reference frequency by 64 to generate an output clock in the range of 6.75GHz-8.25GHz. A superior jitter performance of 190fsrms is achieved, while consuming only 2.25mW power. This translates to a best FoM of -251dB. Unlike conventional PLLs, ILCMs have been fundamentally limited to only integer-N operation and cannot synthesize fractional-N frequencies. In the last part of this thesis, we extend the merits of ILCMs to fractional-N and overcome this fundamental limitation. We employ DTC-based QNC techniques in order to align injected pulses to the oscillator's zero crossings, which enables it to pull the oscillator toward phase lock, thus realizing a fractional-N ILCM. Fabricated in 65nm CMOS process, a prototype 20-bit fractional-N ILCM with an output range of 6.75GHz-8.25GHz consumes only 3.25mW. It achieves excellent jitter performance of 110fsrms and 175fsrms in integer- and fractional-N modes respectively, which translates to the best-reported FoM in both integer- (-255dB) and fractional-N (-252dB) modes. The proposed fractional-N ILCM also features the first-reported rapid on/off capability, where the transient absolute jitter performance at wake-up is bounded below 4ps after less than 4ns. This demonstrates almost instantaneous phase settling. This unique capability enables tremendous energy saving by turning on the clock multiplier only when needed. This energy proportional operation leverages idle times to save power at the system-level of wireline and wireless transceivers