A Fully integrated D-band Direct-Conversion I/Q Transmitter and Receiver Chipset in SiGe BiCMOS Technology

This paper presents design and characterization of single-chip 110-170 GHz (D-band) direct conversion in-phase/quadrature-phase (I/Q) transmitter and receiver monolithic microwave integrated circuits (MMICs), realized in a 130 nm SiGe BiCMOS process with ft/fmax of 250 GHz/370 GHz. The chipset is suitable for low power wideband communication and can be used in both homodyne and heterodyne architectures. The Transmitter chip consists of a six-stage power amplifier, an I/Q modulator, and a LO multiplier chain. The LO multiplier chain consists of frequency sixtupler followed by a two-stage amplifier. It exhibits a single sideband conversion gain of 23 dB and saturated output power of 0 dBm. The 3 dB RF bandwidth is 31 GHz from 114 to 145 GHz. The receiver includes a low noise amplifier, I/Q demodulator and x6 multiplier chain at the LO port. The receiver provides a conversion gain of 27 dB and has a noise figure of 10 dB. It has 3 dB RF bandwidth of 28 GHz from 112-140 GHz. The transmitter and receiver have dc power consumption of 240 mW and 280 mW, respectively. The chip area of each transmitter and receiver circuit is 1.4 mm x 1.1 mm

Millimeter-Wave and Terahertz Transceivers in SiGe BiCMOS Technologies

This invited paper reviews the progress of silicon–germanium (SiGe) bipolar-complementary metal–oxide–semiconductor (BiCMOS) technology-based integrated circuits (ICs) during the last two decades. Focus is set on various transceiver (TRX) realizations in the millimeter-wave range from 60 GHz and at terahertz (THz) frequencies above 300 GHz. This article discusses the development of SiGe technologies and ICs with the latter focusing on the commercially most important applications of radar and beyond 5G wireless communications. A variety of examples ranging from 77-GHz automotive radar to THz sensing as well as the beginnings of 60-GHz wireless communication up to THz chipsets for 100-Gb/s data transmission are recapitulated. This article closes with an outlook on emerging fields of research for future advancement of SiGe TRX performance

Low-power CMOS front-ends for wireless personal area networks

The potential of implementing subthreshold radio frequency circuits in deep sub-micron CMOS technology was investigated for developing low-power front-ends for wireless personal area network (WPAN) applications. It was found that the higher transconductance to bias current ratio in weak inversion could be exploited in developing low-power wireless front-ends, if circuit techniques are employed to mitigate the higher device noise in subthreshold region. The first fully integrated subthreshold low noise amplifier was demonstrated in the GHz frequency range requiring only 260 μW of power consumption. Novel subthreshold variable gain stages and down-conversion mixers were developed. A 2.4 GHz receiver, consuming 540 μW of power, was implemented using a new subthreshold mixer by replacing the conventional active low noise amplifier by a series-resonant passive network that provides both input matching and voltage amplification. The first fully monolithic subthreshold CMOS receiver was also implemented with integrated subthreshold quadrature LO (Local Oscillator) chain for 2.4 GHz WPAN applications. Subthreshold operation, passive voltage amplification, and various low-power circuit techniques such as current reuse, stacking, and differential cross coupling were combined to lower the total power consumption to 2.6 mW. Extremely compact resistive feedback CMOS low noise amplifiers were presented as a cost-effective alternative to narrow band LNAs using high-Q inductors. Techniques to improve linearity and reduce power consumption were presented. The combination of high linearity, low noise figure, high broadband gain, extremely small die area and low power consumption made the proposed LNA architecture a compelling choice for many wireless applications.Ph.D.Committee Chair: Laskar, Joy; Committee Member: Chakraborty, Sudipto; Committee Member: Chang, Jae Joon; Committee Member: Divan, Deepakraj; Committee Member: Kornegay, Kevin; Committee Member: Tentzeris, Emmanoui

A Direct Carrier I/Q Modulator for High-Speed Communication at D-Band Using 130 nm SiGe BiCMOS Technology

This paper presents a 110-170 GHz direct conversion I/Q modulator realized in 130 nm SiGe BiCMOS technology with ft/fmax values of 250 GHz/ 370 GHz. The design is based on double-balanced Gilbert mixer cells with on-chip quadrature LO phase shifter and RF balun. In single-sideband operation, the modulator exhibits up to 9.5 dB conversion gain and has measured 3 dB IF bandwidth of 12 GHz. The measured image rejection ratio and LO to RF isolation are as high as 20 dB and 31 dB respectively. Meas-ured input P1dB is -17 dBm at 127 GHz output. The DC power con-sumption is 53 mW. The active chip area is 620 μm× 480 μm in-cluding the RF and LO baluns. The circuit is capable of transmit-ting more than 12 Gbit/s QPSK signal

Développement d'une architecture innovante de récepteur radar à 77 GHz et démonstration en CMOS 28 nm FDSOI

Grâce à sa capacité à détecter des cibles éloignées malgré une mauvaise visibilité, le radar automobile à 77 GHz joue un rôle important dans l'aide à la conduite. L'utilisation des fréquences millimétriques offre une bonne résolution et une importante capacité d'intégration des circuits. C'est aussi un défi car il faut satisfaire un cahier des charges exigeant sur le bruit et la linéarité du récepteur. Les technologies SiGe BiCMOS ont été les premières utilisées pour la conception de récepteurs radar à 77 GHz. De bons résultats ont été obtenus en se basant sur des architectures utilisant des mélangeurs actifs. Cependant l'utilisation des technologie BiCMOS se traduisait par une consommation élevée, une faible capacité d'intégration et des coûts de production importants. Récemment, l'intégration des procédés CMOS menant à l'augmentation des fréquences de transition rend ces technologies plus attractives pour les applications nécessitant un faible coût et la cointégration de plusieurs fonctions au sein d'une même puce. La littérature sur les récepteurs radars en technologie CMOS à 77 GHz montre que les architectures inspirées par les technologies BiCMOS ne sont pas pertinentes pour cette application. Le but de cette thèse et de montrer que l'utilisation de techniques propres aux technologie CMOS comme l'échantillonnage et l'utilisation de portes logiques permet d'obtenir de très bonnes performances. Dans ce travail, deux nouvelles architectures de récepteurs radars basées sur le principe d'échantillonnage sont proposées. La première architecture est basée sur un mélangeur passif échantillonné qui permet d'obtenir un très bon compromis bruit/linéarité. La seconde exploite les propriétés des mélangeurs sous-échantillonnés afin utiliser une fréquence d'OL trois fois inférieure à la fréquence RF offrant ainsi de très intéressantes simplifications au niveau de la chaîne de distribution du signal d'OL du récepteur. Le contexte de cette étude est expliqué dans le 1er chapitre qui présente les exigences de conception liées à l'application radar et fourni une analyse de l'état de l'art des récepteurs à 77 GHZ. Le chapitre suivant décrit le principe de fonctionnement et l'implémentation d'un mélangeur échantillonné à 77 GHz en technologie CMOS 28- nm FDSOI. Une topologie de mélangeur sous-échantillonné utilisant une fréquence d'OL de 26 GHz pour convertir des signaux RF autour de 77 GHz est ensuite détaillée dans le chapitre 3. Le chapitre 4 conclut cette étude en détaillant l'intégration des mélangeurs étudiés dans les chapitres précédents avec un amplificateur faible bruit dans différents récepteurs radars. Ces architectures de récepteurs basées sur l'échantillonnage sont ensuite comparées entre elles et avec l'état de l'art montrant ainsi leurs avantages et inconvénients. Les résultats de cette comparaison confirment l'intérêt des techniques d'échantillonnage pour la conversion de fréquence dans le cadre de l'application radar.With its ability to detect distant targets under harsh visibility conditions, the 77 GHz automotive radar plays a key role in driving safety. Using mm-wave frequencies allow a good range resolution, a better circuit integration and a wide modulation bandwidth. This is also a challenge for circuit designers who must fulfill stringent requirements especially on the receiver front-end. First 77 GHz radar receivers were manufactured with SiGe BiCMOS processes benefiting from the high transition frequency and high breakdown voltage of Hetero-junction Bipolar Transistors (HBT). Good results have been achieved with active-mixer-based architectures, but these technologies suffer from high power consumptions, limited integration capacity and large production cost. More recently, the scaling down of CMOS processes (coming together with the increase of the transition frequency of the transistors) makes CMOS a good candidate for 77 GHz circuit design, especially when cost target requires single chip solutions. The literature related to CMOS radar receivers highlights that receivers based on BiCMOS architectures generally show poor performances. The aim of this work is to demonstrate that using CMOS specific technics such as sampling and the use of high-speed digital gates should enhance the performance of the receivers. In this work, two innovative radar receiver architectures based on the sampling principle are proposed. The first one shows that this principle can be extended to millimeter wave frequencies to benefit from a very good noise/linearity trade-off. While the second one uses this principle to converts a 77 GHz RF signal by using a 26 GHz LO frequency thus simplifying the LO distribution chain of the receiver. The background of this study is introduced in the chapter 1 presenting the design trade-off related to the 77 GHz radar receiver and provides a review of the existing solutions. The following chapter describes the sampling mixer principle and the implementation of a 77 GHz sampling mixer in 28-nm FDSOI CMOS technology. Then, a sub- sampling mixer topology allowing to convert an RF signal around 77 GHz using a 26 GHz LO frequency is detailed in the chapter 3. The chapter 4 draws the conclusion of this study by showing the implementation of the two proposed sampling-based mixers with a low noise amplifier in 77 GHz front ends. These receiver architectures are compared with the state of the art highlighting the strengths and weaknesses of the proposed solutions. The results of this study demonstrates that using sampling for down conversion can be convenient to address millimeter-wave frequency applications

Millimeter-wave Communication and Radar Sensing — Opportunities, Challenges, and Solutions

With the development of communication and radar sensing technology, people are able to seek for a more convenient life and better experiences. The fifth generation (5G) mobile network provides high speed communication and internet services with a data rate up to several gigabit per second (Gbps). In addition, 5G offers great opportunities of emerging applications, for example, manufacture automation with the help of precise wireless sensing. For future communication and sensing systems, increasing capacity and accuracy is desired, which can be realized at millimeter-wave spectrum from 30 GHz to 300 GHz with several tens of GHz available bandwidth. Wavelength reduces at higher frequency, this implies more compact transceivers and antennas, and high sensing accuracy and imaging resolution. Challenges arise with these application opportunities when it comes to realizing prototype or demonstrators in practice. This thesis proposes some of the solutions addressing such challenges in a laboratory environment.High data rate millimeter-wave transmission experiments have been demonstrated with the help of advanced instrumentations. These demonstrations show the potential of transceiver chipsets. On the other hand, the real-time communication demonstrations are limited to either low modulation order signals or low symbol rate transmissions. The reason for that is the lack of commercially available high-speed analog-to-digital converters (ADCs); therefore, conventional digital synchronization methods are difficult to implement in real-time systems at very high data rates. In this thesis, two synchronous baseband receivers are proposed with carrier recovery subsystems which only require low-speed ADCs [A][B].Besides synchronization, high-frequency signal generation is also a challenge in millimeter-wave communications. The frequency divider is a critical component of a millimeter-wave frequency synthesizer. Having both wide locking range and high working frequencies is a challenge. In this thesis, a tunable delay gated ring oscillator topology is proposed for dual-mode operation and bandwidth extension [C]. Millimeter-wave radar offers advantages for high accuracy sensing. Traditional millimeter-wave radar with frequency-modulated continuous-wave (FMCW), or continuous-wave (CW), all have their disadvantages. Typically, the FMCW radar cannot share the spectrum with other FMCW radars.\ua0 With limited bandwidth, the number of FMCW radars that could coexist in the same area is limited. CW radars have a limited ambiguous distance of a wavelength. In this thesis, a phase-modulated radar with micrometer accuracy is presented [D]. It is applicable in a multi-radar scenario without occupying more bandwidth, and its ambiguous distance is also much larger than the CW radar. Orthogonal frequency-division multiplexing (OFDM) radar has similar properties. However, its traditional fast calculation method, fast Fourier transform (FFT), limits its measurement accuracy. In this thesis, an accuracy enhancement technique is introduced to increase the measurement accuracy up to the micrometer level [E]

Concepts for Short Range Millimeter-wave Miniaturized Radar Systems with Built-in Self-Test

This work explores short-range millimeter wave radar systems, with emphasis on miniaturization and overall system cost reduction. The designing and implementation processes, starting from the system level design considerations and characterization of the individual components to final implementation of the proposed architecture are described briefly. Several D-band radar systems are developed and their functionality and performances are demonstrated

Millimeter-Wave Super-Regenerative Receivers for Wireless Communication and Radar

Today’s world is becoming increasingly automated and interconnected with billions of smart devices coming online, leading to a steep rise in energy consumption from small microelectronics. This coincides with an urgent push to transform global energy production to green energies, causing disruptions and energy shortages, and making the case for efficient energy use ever more pressing. Two major areas where high growth is expected are the fields of wireless communication and radar sensors. Millimeter-wave frequency bands are planned for fifth-generation (5G) and sixth-generation (6G) cellular communication standards, as well as automotive frequency-modulated continuous wave (FMCW) radar systems for driving assistance and automation. Fast silicon-based technologies enable these advances by operating at high maximum frequencies, such as the silicon-germanium (SiGe) heterojunction bipolar transistor (HBT) technologies. However, even the fastest transistors suffer from low and energy expensive gains at millimeter-wave frequencies. Rather than incremental improvements in circuit efficiency using conventional approaches, a disruptive revolution for green microelectronics could be enabled by exploring the low-power benefits of the super-regenerative receiver for some applications. The super-regenerative receiver uses a regenerative oscillator circuit to increase the gain by positive feedback, through coupling energy from the output back into the input. Careful bias and control of the circuit enables a very large gain from a small number of transistors and a very low energy dissipation. Thus, the super-regenerative oscillator could be used to replace amplifier circuits in high data rate wireless communication systems, or as active reflectors to increase the range of FMCW radar systems, greatly reducing the power consumption. The work in this thesis presents fundamental scientific research into the topic of energy-efficient millimeter-wave super-regenerative receivers for use in civilian wireless communication and radar applications. This research work covers the theory, analysis, and simulations, all the way up to the proof of concept, hardware realization, and experimental characterization. Analysis and modeling of regenerative oscillator circuits is presented and used to improve the understanding of the circuit operation, as well as design goals according to the specific application needs. Integrated circuits are investigated and characterized as a proof of concept for a high data rate wireless communication system operating between 140–220 GHz, and an automotive radar system operating at 60 GHz. Amplitude and phase regeneration capabilities for complex modulation are investigated, and principles for spectrum characterization are derived. The circuits are designed and fabricated in a 130 nm SiGe HBT technology, combining bipolar and complementary metal-oxide semiconductor (BiCMOS) transistors. To prove the feasibility of the research concepts, the work achieves a wireless communication link at 16 Gbit/s over 20 cm distance with quadrature amplitude modulation (QAM), which is a world record for the highest data rate ever reported in super-regenerative circuits. This was powered by a super-regenerative oscillator circuit operating at 180 GHz and providing 58 dB of gain. Energy efficiency is also considerably high, drawing 8.8 mW of dc power consumption, which corresponds to a highly efficient 0.6 pJ/bit. Packaging and module integration innovations were implemented for the system experiments, and additional broadband circuits were investigated to generate custom quench waveforms to further enhance the data rate. For radar active reflectors, a regenerative gain of 80 dB is achieved at 60 GHz from a single circuit, which is the best in its frequency range, despite a low dc power consumption of 25 mW

Passive Millimeter-Wave Imaging Based on Subharmonic Self-Oscillating Mixing

RÉSUMÉ Le sujet général de la thèse de doctorat présentée réside dans la recherche sur des nouvelles méthodes dans le domaine de l’imagerie aux micro-ondes, en particulier l’imagerie passive aux ondes millimétriques, qui est aussi connue sous le nom d’imagerie radiométrique. Cette dernière technique est utilisée pour former une image d’une scène particulière en capturant la radiation électromagnétique émise naturellement par chaque objet à la bande de fréquence des micro-ondes / ondes millimétriques, similaire à la façon dont une photographie est prise en capturant la radiation aux fréquences optiques. De cette façon, une image d’ondes millimétriques peut être formée et utilisée pour tracer différentes caractéristiques de la scène ou de l’objet, qui sont implicites à la bande de fréquences des micro-ondes / ondes millimétriques. L’imagerie à ondes millimétriques représente un des sujets d’actualité des plus prometteurs dans le domaine de la conception des capteurs à haute fréquence. L’utilité de cette technique réside surtout dans les particularités des phénomènes de l’atténuation atmosphérique permettant aux ondes millimétriques de pénétrer à travers une grande variété de conditions de mauvaise visibilité, comme par exemple la brume, le brouillard, les nuages, la fumée et les tempêtes de sable, ainsi que la capacité de se propager à travers des vêtements et certains autres matériaux. Outre ces avantages par rapport aux systèmes infrarouges ou optiques, les systèmes à ondes millimétriques surpassent les systèmes micro-ondes à plus basse fréquence par leurs longueurs d’ondes plus petites permettant d’atteindre une plus haute résolution. Pour leur mise en application, des fenêtres de propagation à 35, 77, 94, 140 et 220 GHz ont été assignées. Les domaines d’application présents et futurs sont principalement associés aux infrastructures militaires et commerciales. Ceux-ci englobent la surveillance, la navigation et la technologie automobile, ainsi que l’atterrissage des avions et le suivi de la circulation dans le brouillard sur les autoroutes. De plus, la demande de plus en plus grande en systèmes de détection de sécurité aux aéroports et d’autres lieux publics crée une demande toujours plus grande en scanners automatisés en temps réel dotés des caractéristiques suivantes : ne présenter aucun risque pour la santé, générer un nombre réduit de fausses alertes et permettre la détection des armes cachées ou des objets dangereux à travers les vêtements.----------ABSTRACT The broad topic of the presented Ph.D. thesis consists in the research on novel methods in the field of microwave imaging, in particular the so-called passive millimetre-wave imaging, which is also referred to as radiometric imaging. This latter technique is used to form an image of a particular scene by means of sensing the natural electromagnetic radiation emitted by any object at microwave / millimetre-wave wavelengths, similar to the way in which a photograph is captured by sensing the radiation occurring at optical wavelengths. In this way, different characteristics of the observed scene or object, which are inherent to the microwave / millimetre-wave frequency range, can be mapped in the form of an image. Millimetre-wave imaging represents one of today’s most promising research topics in the field of high frequency sensor design. The usefulness of this technique lies in particular in the peculiarities of atmospheric attenuation phenomenologies allowing millimetre-waves to penetrate through a variety of low-visibility conditions such as haze, fog, clouds, smoke, and sandstorms and furthermore in the ability to propagate through clothing and a number of other materials. Together with these advantages over infrared and optical systems, moreover, millimetre-wave systems outperform imagers at the lower microwave frequency range due to their smaller wavelengths and the thus achievable higher resolution. For their implementation, propagation windows at 35, 77, 94, 140, and 220 GHz are generally allocated. Present and future applications consist in both military and commercial infrastructure fields such as in surveillance, navigation, and automotive technology, as well as aircraft landing or highway traffic monitoring in fog. Moreover, the ever increasing demand for security screening systems at airports and other public environments creates a growing need for health-hazardless automated real-time scanners with minimized false alarms, and millimetre-wave imaging offering the ability to detect concealed weapons or hazardous objects through clothing material represents an excellent choice for this purpose. Furthermore, millimetre-wave imaging is applied to biomedical imaging such as the location of hot spots, tumours, or other anomalies in the body. Additional applications consist in non-destructive material testing and geological examinations such as the sensing of the Earth’s atmosphere, oil spill detection, research on volcano activity, or meteorology