IDDQ testing of a CMOS first order sigma-delta modulator of an 8-bit oversampling ADC

This work presents IDDQ testing of a CMOS first order sigma-delta modulator of an 8-bit oversampling analog-to-digital converter using a built-in current sensor [BICS]. Gate-drain, source-drain, gate-source and gate-substrate bridging faults are injected using fault injection transistors. All the four faults cause varying fault currents and are successfully detected by the BICS at a good operation speed. The BICS have a negligible impact on the performance of the modulator and an external pin is provided to completely cut-off the BICS from the modulator. The modulator was designed and fabricated in 1.5 μm n-well CMOS process. The decimator was designed on Altera\u27s FLEXE20K board using Verilog. The modulator and decimator were assembled together to form a sigma-delta ADC

Programmable CMOS Analog-to-Digital Converter Design and Testability

In this work, a programmable second order oversampling CMOS delta-sigma analog-to-digital converter (ADC) design in 0.5µm n-well CMOS processes is presented for integration in sensor nodes for wireless sensor networks. The digital cascaded integrator comb (CIC) decimation filter is designed to operate at three different oversampling ratios of 16, 32 and 64 to give three different resolutions of 9, 12 and 14 bits, respectively which impact the power consumption of the sensor nodes. Since the major part of power consumed in the CIC decimator is by the integrators, an alternate design is introduced by inserting coder circuits and reusing the same integrators for different resolutions and oversampling ratios to reduce power consumption. The measured peak signal-to-noise ratio (SNR) for the designed second order delta-sigma modulator is 75.6dB at an oversampling ratio of 64, 62.3dB at an oversampling ratio of 32 and 45.3dB at an oversampling ratio of 16. The implementation of a built-in current sensor (BICS) which takes into account the increased background current of defect-free circuits and the effects of process variation on ΔIDDQ testing of CMOS data converters is also presented. The BICS uses frequency as the output for fault detection in CUT. A fault is detected when the output frequency deviates more than ±10% from the reference frequency. The output frequencies of the BICS for various model parameters are simulated to check for the effect of process variation on the frequency deviation. A design for on-chip testability of CMOS ADC by linear ramp histogram technique using synchronous counter as register in code detection unit (CDU) is also presented. A brief overview of the histogram technique, the formulae used to calculate the ADC parameters, the design implemented in 0.5µm n-well CMOS process, the results and effectiveness of the design are described. Registers in this design are replaced by 6T-SRAM cells and a hardware optimized on-chip testability of CMOS ADC by linear ramp histogram technique using 6T-SRAM as register in CDU is presented. The on-chip linear ramp histogram technique can be seamlessly combined with ΔIDDQ technique for improved testability, increased fault coverage and reliable operation

Quiescent current testing of CMOS data converters

Power supply quiescent current (IDDQ) testing has been very effective in VLSI circuits designed in CMOS processes detecting physical defects such as open and shorts and bridging defects. However, in sub-micron VLSI circuits, IDDQ is masked by the increased subthreshold (leakage) current of MOSFETs affecting the efficiency of I¬DDQ testing. In this work, an attempt has been made to perform robust IDDQ testing in presence of increased leakage current by suitably modifying some of the test methods normally used in industry. Digital CMOS integrated circuits have been tested successfully using IDDQ and IDDQ methods for physical defects. However, testing of analog circuits is still a problem due to variation in design from one specific application to other. The increased leakage current further complicates not only the design but also testing. Mixed-signal integrated circuits such as the data converters are even more difficult to test because both analog and digital functions are built on the same substrate. We have re-examined both IDDQ and IDDQ methods of testing digital CMOS VLSI circuits and added features to minimize the influence of leakage current. We have designed built-in current sensors (BICS) for on-chip testing of analog and mixed-signal integrated circuits. We have also combined quiescent current testing with oscillation and transient current test techniques to map large number of manufacturing defects on a chip. In testing, we have used a simple method of injecting faults simulating manufacturing defects invented in our VLSI research group. We present design and testing of analog and mixed-signal integrated circuits with on-chip BICS such as an operational amplifier, 12-bit charge scaling architecture based digital-to-analog converter (DAC), 12-bit recycling architecture based analog-to-digital converter (ADC) and operational amplifier with floating gate inputs. The designed circuits are fabricated in 0.5 μm and 1.5 μm n-well CMOS processes and tested. Experimentally observed results of the fabricated devices are compared with simulations from SPICE using MOS level 3 and BSIM3.1 model parameters for 1.5 μm and 0.5 μm n-well CMOS technologies, respectively. We have also explored the possibility of using noise in VLSI circuits for testing defects and present the method we have developed

Iddq testing of a CMOS 10-bit charge scaling digital-to-analog converter

This work presents an effective built-in current sensor (BICS), which has a very small impact on the performance of the circuit under test (CUT). The proposed BICS works in two-modes the normal mode and the test mode. In the normal mode the BICS is isolated from the CUT due to which there is no performance degradation of the CUT. In the testing mode, our BICS detects the abnormal current caused by permanent manufacturing defects. Further more our BICS can also distinguish the type of defect induced (Gate-source short, source-drain short and drain-gate short). Our BICS requires neither an external voltage source nor current source. Hence the BICS requires less area and is more efficient than the conventional current sensors. The circuit under test is a 10-bit digital to analog converter using charge-scaling architecture

Testing a CMOS operational amplifier circuit using a combination of oscillation and IDDQ test methods

This work presents a case study, which attempts to improve the fault diagnosis and testability of the oscillation testing methodology applied to a typical two-stage CMOS operational amplifier. The proposed test method takes the advantage of good fault coverage through the use of a simple oscillation based test technique, which needs no test signal generation and combines it with quiescent supply current (IDDQ) testing to provide a fault confirmation. A built in current sensor (BICS), which introduces insignificant performance degradation of the circuit-under-test (CUT), has been utilized to monitor the power supply quiescent current changes in the CUT. The testability has also been enhanced in the testing procedure using a simple fault-injection technique. The approach is attractive for its simplicity, robustness and capability of built-in-self test (BIST) implementation. It can also be generalized to the oscillation based test structures of other CMOS analog and mixed-signal integrated circuits. The practical results and simulations confirm the functionality of the proposed test method

Integrated circuit outlier identification by multiple parameter correlation

Semiconductor manufacturers must ensure that chips conform to their specifications before they are shipped to customers. This is achieved by testing various parameters of a chip to determine whether it is defective or not. Separating defective chips from fault-free ones is relatively straightforward for functional or other Boolean tests that produce a go/no-go type of result. However, making this distinction is extremely challenging for parametric tests. Owing to continuous distributions of parameters, any pass/fail threshold results in yield loss and/or test escapes. The continuous advances in process technology, increased process variations and inaccurate fault models all make this even worse. The pass/fail thresholds for such tests are usually set using prior experience or by a combination of visual inspection and engineering judgment. Many chips have parameters that exceed certain thresholds but pass Boolean tests. Owing to the imperfect nature of tests, to determine whether these chips (called "outliers") are indeed defective is nontrivial. To avoid wasted investment in packaging or further testing it is important to screen defective chips early in a test flow. Moreover, if seemingly strange behavior of outlier chips can be explained with the help of certain process parameters or by correlating additional test data, such chips can be retained in the test flow before they are proved to be fatally flawed. In this research, we investigate several methods to identify true outliers (defective chips, or chips that lead to functional failure) from apparent outliers (seemingly defective, but fault-free chips). The outlier identification methods in this research primarily rely on wafer-level spatial correlation, but also use additional test parameters. These methods are evaluated and validated using industrial test data. The potential of these methods to reduce burn-in is discussed

Variance reduction and outlier identification for IDDQ testing of integrated chips using principal component analysis

Integrated circuits manufactured in current technology consist of millions of transistors with dimensions shrinking into the nanometer range. These small transistors have quiescent (leakage) currents that are increasingly sensitive to process variations, which have increased the variation in good-chip quiescent current and consequently reduced the effectiveness of IDDQ testing. This research proposes the use of a multivariate statistical technique known as principal component analysis for the purpose of variance reduction. Outlier analysis is applied to the reduced leakage current values as well as the good chip leakage current estimate, to identify defective chips. The proposed idea is evaluated using IDDQ values from multiple wafers of an industrial chip fabricated in 130 nm technology. It is shown that the proposed method achieves significant variance reduction and identifies many outliers that escape identification by other established techniques. For example, it identifies many of the absolute outliers in bad neighborhoods, which are not detected by Nearest Neighbor Residual and Nearest Current Ratio. It also identifies many of the spatial outliers that pass when using Current Ratio. The proposed method also identifies both active and passive defects

Constraint-driven RF test stimulus generation and built-in test

With the explosive growth in wireless applications, the last decade witnessed an ever-increasing test challenge for radio frequency (RF) circuits. While the design community has pushed the envelope far into the future, by expanding CMOS process to be used with high-frequency wireless devices, test methodology has not advanced at the same pace. Consequently, testing such devices has become a major bottleneck in high-volume production, further driven by the growing need for tighter quality control. RF devices undergo testing during the prototype phase and during high-volume manufacturing (HVM). The benchtop test equipment used throughout prototyping is very precise yet specialized for a subset of functionalities. HVM calls for a different kind of test paradigm that emphasizes throughput and sufficiency, during which the projected performance parameters are measured one by one for each device by automated test equipment (ATE) and compared against defined limits called specifications. The set of tests required for each product differs greatly in terms of the equipment required and the time taken to test individual devices. Together with signal integrity, precision, and repeatability concerns, the initial cost of RF ATE is prohibitively high. As more functionality and protocols are integrated into a single RF device, the required number of specifications to be tested also increases, adding to the overall cost of testing, both in terms of the initial and recurring operating costs. In addition to the cost problem, RF testing proposes another challenge when these components are integrated into package-level system solutions. In systems-on-packages (SOP), the test problems resulting from signal integrity, input/output bandwidth (IO), and limited controllability and observability have initiated a paradigm shift in high-speed analog testing, favoring alternative approaches such as built-in tests (BIT) where the test functionality is brought into the package. This scheme can make use of a low-cost external tester connected through a low-bandwidth link in order to perform demanding response evaluations, as well as make use of the analog-to-digital converters and the digital signal processors available in the package to facilitate testing. Although research on analog built-in test has demonstrated hardware solutions for single specifications, the paradigm shift calls for a rather general approach in which a single methodology can be applied across different devices, and multiple specifications can be verified through a single test hardware unit, minimizing the area overhead. Specification-based alternate test methodology provides a suitable and flexible platform for handling the challenges addressed above. In this thesis, a framework that integrates ATE and system constraints into test stimulus generation and test response extraction is presented for the efficient production testing of high-performance RF devices using specification-based alternate tests. The main components of the presented framework are as follows: Constraint-driven RF alternate test stimulus generation: An automated test stimulus generation algorithm for RF devices that are evaluated by a specification-based alternate test solution is developed. The high-level models of the test signal path define constraints in the search space of the optimized test stimulus. These models are generated in enough detail such that they inherently define limitations of the low-cost ATE and the I/O restrictions of the device under test (DUT), yet they are simple enough that the non-linear optimization problem can be solved empirically in a reasonable amount of time. Feature extractors for BIT: A methodology for the built-in testing of RF devices integrated into SOPs is developed using additional hardware components. These hardware components correlate the high-bandwidth test response to low bandwidth signatures while extracting the test-critical features of the DUT. Supervised learning is used to map these extracted features, which otherwise are too complicated to decipher by plain mathematical analysis, into the specifications under test. Defect-based alternate testing of RF circuits: A methodology for the efficient testing of RF devices with low-cost defect-based alternate tests is developed. The signature of the DUT is probabilistically compared with a class of defect-free device signatures to explore possible corners under acceptable levels of process parameter variations. Such a defect filter applies discrimination rules generated by a supervised classifier and eliminates the need for a library of possible catastrophic defects.Ph.D.Committee Chair: Chatterjee, Abhijit; Committee Member: Durgin, Greg; Committee Member: Keezer, David; Committee Member: Milor, Linda; Committee Member: Sitaraman, Sures

Voltage sensing based built-in current sensor for IDDQ test

Quiescent current leakage test of the VDD supply (IDDQ Test) has been proven an effective way to screen out defective chips in manufacturing of Integrated Circuits (IC). As technology advances, the traditional IDDQ test is facing more and more challenges. In this research, a practical built-in current sensor (BICS) is proposed and the design is verified by three generations of test chips. The BICS detects the signal by sensing the voltage drop on supply lines of the circuit under test (CUT). Then the sensor performs analog-to-digital conversion of the input signal using a stochastic process with scan chain readout. Self-calibration and digital chopping are used to minimize offset and low frequency noise and drift. This non-invasive procedure avoids any performance degradation of the CUT. The measurement results of test chips are presented. The sensor achieves a high IDDQ resolution with small chip area overhead. This will enable IDDQ of future technology generations