Physical Layer Security using Time-Reversal Pre-Coding based OFDM-DCSK Communication System with Artificial Noise Injection

In this paper, Time-Reversal (TR) pre-coding with Artificial Noise (AN) injection is proposed to enhance the physical layer security (PLS) performance in orthogonal Frequency Division Multiplexing-Differential Chaos Shift Keying (OFDM-DCSK) system, which is named the TRAN-OFDM-DCSK system. This approach is provided to achieve high data rates, high PL data security, and high reliability performance. The AN signal does not spoil the transmitted data to the genuine receiver, but it reduces the ungenuine detection performance. This system ensures the secrecy of communication to the genuine receiver when the sender knows the Channel State Information (CSI) of the genuine communication link. Still, the information about the instantaneous CSI of a possible eavesdropper does not know the transmitter. The performance of the proposed TRAN-OFDM-DCSK system is investigated and tested under a Flat Rayleigh Fading Channel (FRFC). An approach is provided for calculating the performance of Bit Error Rate (BER), and the expression of BER analytical is derived and compared with the simulation version. Furthermore, the ergodic Secrecy Rate (SR) is derived and analyzed at the genuine and ungenuine receivers over the FRFC. Our result shows the best performance for the genuine receiver compared with ungenuine receiver regarding secrecy performance for BER and SR

Advanced index modulation techniques for future wireless networks

In the research study proposed in this Ph.D Thesis, we consider Index Modulation as a novel tool to enhance energy and spectral efficiencies for upcoming 5G networks, including wireless sensor networks and internet of things. In this vein, spatial modulation was proposed to enhance the capacity of wireless systems to partially achieve the capacity of MIMO systems but at lower cost, making it a technique that has attracted significant attention over the past few years. As such, SM schemes have been regarded as possible candidates for spectrum- and energy-efficient next generation MIMO systems. However, the implementation of the SM is also challenging because of its heavy dependence on channel characteristics, channel correlation, corrupted CSI and the need to have adequate spacing between antennas. Moreover, the SM requires multiple antennas at the transmitter which adds cost to the hardware implementation. In addition, the number of mapped bits in SM is limited by the physical size of the wireless device where only small number of antennas can be used. The switching time wasted by RF antenna switches adds to the complexity of the issue. In this Thesis, we study the drawbacks of SM in the articles indicated, namely Performance Comparison of Spatial Modulation Detectors Under Channel Impairments that is placed in the Appendix at the end of Thesis as it is a conference paper, and The Impact of Antenna Switching Time on Spatial Modulation that is put in Chapter 1. In the first article, we have shown that channel impairments have serious impacts on the BER performance and on the capacity of the SM system and that the SM is too sensitive to both imperfect and correlated channels. In the second article, we have demonstrated that the switching time defined as the time needed by the system to turn off an antenna and turn on another one, which is an inherent property of RF industrial switches used in SM systems, is in the order of nanoseconds and naturally influences the transmission rate of SM systems because of introducing systematic transmission gaps or pauses. Given the speed limitation of practical RF switches in performing transitions, antenna transition-based technologies like SM schemes are capped in terms of data rate performance. In fact, the effective data rate of SM will remain hostage to developments in industrial RF switches. This brings restrictions to the implementation and operation issues when extremely high data rates become a necessity. It is shown by the assemblage of our results that the switching time Tsw which is a requirement for transitions between antennas to happen, dictates restrictions on data rate, capacity and spectral efficiency of SM systems. Furthermore, we propose baseband non-hardware-based indexing modulation schemes based on frequency-index modulation, coherent chaotic modulation and non-coherent differential chaotic modulation schemes as potential alternatives to SM, that would also fit wireless sensor networks and internet of things applications. In this regard, we have proposed three articles. The first article which represents frequency index modulation is called Frequency Index Modulation for Low Complexity Low Energy Communication Networks and is placed in Chapter 2 of this Thesis. In this article, we explore a low complexity multi-user communication system based on frequency index modulation that suits Internet of Things (IoT) applications and we show that such a system would constitute an excellent candidate for wireless sensor applications, where it represents a simpler substitution for frequency-hopping (FH) based architectures, in which the hops carry extra bits. The third article which concerns coherent chaotic modulation is called Design of an Initial-Condition Index Chaos Shift Keying Modulation and is located in Chapter 3. In this article, an initial condition index chaos shift keying modulation is proposed. This design aims to increase the spectral and energy efficiencies to unprecedented levels. The proposed scheme exploits the initial conditions to generate different chaotic sequences to convey extra bits per transmission. In comparison to rival modulation schemes, the results obtained in the proposed work show a promising data rate boost and a competitive performance. The last article employs a non-coherent differential chaotic shift-key system named Permutation Index DCSK Modulation Technique for Secure Multi-User High-Data-Rate Communication Systems that is found in the Appendix. In this original design, where each data frame is divided into two time slots in which the reference chaotic signal is sent in the first time slot and a permuted replica of the reference signal multiplied by the modulating bit is sent in the second time slot, we target enhancing data security, energy and spectral efficiencies. Overall, in light of the high demands for bandwidth and energy efficiencies of futuristic systems, the suggested soft indexing mechanisms are successful candidates with promising results

Journal of Telecommunications and Information Technology

kwartalni

Joint signal detection and channel estimation in rank-deficient MIMO systems

L'évolution de la prospère famille des standards 802.11 a encouragé le développement des technologies appliquées aux réseaux locaux sans fil (WLANs). Pour faire face à la toujours croissante nécessité de rendre possible les communications à très haut débit, les systèmes à antennes multiples (MIMO) sont une solution viable. Ils ont l'avantage d'accroître le débit de transmission sans avoir recours à plus de puissance ou de largeur de bande. Cependant, l'industrie hésite encore à augmenter le nombre d'antennes des portables et des accésoires sans fil. De plus, à l'intérieur des bâtiments, la déficience de rang de la matrice de canal peut se produire dû à la nature de la dispersion des parcours de propagation, ce phénomène est aussi occasionné à l'extérieur par de longues distances de transmission. Ce projet est motivé par les raisons décrites antérieurement, il se veut un étude sur la viabilité des transcepteurs sans fil à large bande capables de régulariser la déficience de rang du canal sans fil. On vise le développement des techniques capables de séparer M signaux co-canal, même avec une seule antenne et à faire une estimation précise du canal. Les solutions décrites dans ce document cherchent à surmonter les difficultés posées par le medium aux transcepteurs sans fil à large bande. Le résultat de cette étude est un algorithme transcepteur approprié aux systèmes MIMO à rang déficient

Robust wireless sensor network for smart grid communication : modeling and performance evaluation

Our planet is gradually heading towards an energy famine due to growing population and industrialization. Hence, increasing electricity consumption and prices, diminishing fossil fuels and lack significantly in environment-friendliness due to their emission of greenhouse gasses, and inefficient usage of existing energy supplies have caused serious network congestion problems in many countries in recent years. In addition to this overstressed situation, nowadays, the electric power system is facing many challenges, such as high maintenance cost, aging equipment, lack of effective fault diagnostics, power supply reliability, etc., which further increase the possibility of system breakdown. Furthermore, the adaptation of the new renewable energy sources with the existing power plants to provide an alternative way for electricity production transformed it in a very large and complex scale, which increases new issues. To address these challenges, a new concept of next generation electric power system, called the "smart grid", has emerged in which Information and Communication Technologies (ICTs) are playing the key role. For a reliable smart grid, monitoring and control of power system parameters in the transmission and distribution segments are crucial. This necessitates the deployment of a robust communication network within the power grid. Traditionally, power grid communications are realized through wired communications, including power line communication (PLC). However, the cost of its installation might be expensive especially for remote control and monitoring applications. More recently, plenty of research interests have been drawn to the wireless communications for smart grid applications. In this regard, the most promising methods of smart grid monitoring explored in the literature is based on wireless sensor network (WSN). Indeed, the collaborative nature of WSN brings significant advantages over the traditional wireless networks, including low-cost, wider coverage, self-organization, and rapid deployment. Unfortunately, harsh and hostile electric power system environments pose great challenges in the reliability of sensor node communications because of strong RF interference and noise called impulsive noise. On account of the fundamental of WSN-based smart grid communications and the possible impacts of impulsive noise on the reliability of sensor node communications, this dissertation is supposed to further fill the lacking of the existing research outcomes. To be specific, the contributions of this dissertation can be summarized as three fold: (i) investigation and performance analysis of impulsive noise mitigation techniques for point-to-point single-carrier communication systems impaired by bursty impulsive noise; (ii) design and performance analysis of collaborative WSN for smart grid communication by considering the RF noise model in the designing process, a particular intension is given to how the time-correlation among the noise samples can be taken into account; (iii) optimal minimum mean square error (MMSE)estimation of physical phenomenon like temperature, current, voltage, etc., typically modeled by a Gaussian source in the presence of impulsive noise. In the first part, we compare and analyze the widely used non-linear methods such as clipping, blanking, and combined clipping-blanking to mitigate the noxious effects of bursty impulsive noise for point-to-point communication systems with low-density parity-check (LDPC) coded single-carrier transmission. While, the performance of these mitigation techniques are widely investigated for multi-carrier communication systems using orthogonal frequency division multiplexing (OFDM) transmission under the effect of memoryless impulsive noise, we note that OFDM is outperformed by its single-carrier counterpart when the impulses are very strong and/or they occur frequently, which likely exists in contemporary communication systems including smart grid communications. Likewise, the assumption of memoryless noise model is not valid for many communication scenarios. Moreover, we propose log-likelihood ratio (LLR)-based impulsive noise mitigation for the considered scenario. We show that the memory property of the noise can be exploited in the LLR calculation through maximum a posteriori (MAP) detection. In this context, provided simulation results highlight the superiority of the LLR-based mitigation scheme over the simple clipping/blanking schemes. The second contribution can be divided into two aspects: (i) we consider the performance analysis of a single-relay decode-and-forward (DF) cooperative relaying scheme over channels impaired by bursty impulsive noise. For this channel, the bit error rate (BER) performances of direct transmission and a DF relaying scheme using M-PSK modulation in the presence of Rayleigh fading with a MAP receiver are derived; (ii) as a continuation of single-relay collaborative WSN scheme, we propose a novel relay selection protocol for a multi-relay DF collaborative WSN taking into account the bursty impulsive noise. The proposed protocol chooses the N’th best relay considering both the channel gains and the states of the impulsive noise of the source-relay and relay-destination links. To analyze the performance of the proposed protocol, we first derive closed-form expressions for the probability density function (PDF) of the received SNR. Then, these PDFs are used to derive closed-form expressions for the BER and the outage probability. Finally, we also derive the asymptotic BER and outage expressions to quantify the diversity benefits. From the obtained results, it is seen that the proposed receivers based on the MAP detection criterion is the most suitable one for bursty impulsive noise environments as it has been designed according to the statistical behavior of the noise. Different from the aforementioned contributions, talked about the reliable detection of finite alphabets in the presence of bursty impulsive noise, in the thrid part, we investigate the optimal MMSE estimation for a scalar Gaussian source impaired by impulsive noise. In Chapter 5, the MMSE optimal Bayesian estimation for a scalar Gaussian source, in the presence of bursty impulsive noise is considered. On the other hand, in Chapter 6, we investigate the distributed estimation of a scalar Gaussian source in WSNs in the presence of Middleton class-A noise. From the obtained results we conclude that the proposed optimal MMSE estimator outperforms the linear MMSE estimator developed for Gaussian channel

Optimization and Applications of Modern Wireless Networks and Symmetry

Due to the future demands of wireless communications, this book focuses on channel coding, multi-access, network protocol, and the related techniques for IoT/5G. Channel coding is widely used to enhance reliability and spectral efficiency. In particular, low-density parity check (LDPC) codes and polar codes are optimized for next wireless standard. Moreover, advanced network protocol is developed to improve wireless throughput. This invokes a great deal of attention on modern communications

A Comprehensive Survey of the Tactile Internet: State of the art and Research Directions

The Internet has made several giant leaps over the years, from a fixed to a mobile Internet, then to the Internet of Things, and now to a Tactile Internet. The Tactile Internet goes far beyond data, audio and video delivery over fixed and mobile networks, and even beyond allowing communication and collaboration among things. It is expected to enable haptic communication and allow skill set delivery over networks. Some examples of potential applications are tele-surgery, vehicle fleets, augmented reality and industrial process automation. Several papers already cover many of the Tactile Internet-related concepts and technologies, such as haptic codecs, applications, and supporting technologies. However, none of them offers a comprehensive survey of the Tactile Internet, including its architectures and algorithms. Furthermore, none of them provides a systematic and critical review of the existing solutions. To address these lacunae, we provide a comprehensive survey of the architectures and algorithms proposed to date for the Tactile Internet. In addition, we critically review them using a well-defined set of requirements and discuss some of the lessons learned as well as the most promising research directions

A secure and robust frequency and time diversity aided OFDM-DCSK modulation system not requiring channel state information

In this paper, we propose a novel two-dimensional frequency and time diversity aided orthogonal frequency division multiplexing based differential chaos shift keying (OFDM-DCSK) system. Our aim is to provide secure and robust transmissions for practical wireless systems, where perfect channel state information (CSI) may not be available at the receiver, by exploiting the natural high security of chaotic sequences and frequency diversity gains brought by the frequency hopping (FH). In our design, the information bits are firstly modulated by chaotic chips, then non-repetitive FH operations are performed on both reference chips and chaotic modulated symbols. After the inverse fast Fourier transform (IFFT), the non-repetitive reference chips and chaotic modulated symbols are respectively transmitted over different subcarriers. Subsequently, the receiver recovers the information using the received reference chaotic chips which naturally embed the channel frequency response (CFR) of all subcarriers. We then analyze the energy and spectral efficiencies, derive the bit error rate (BER) and information leakage expressions, and provide a detailed complexity analysis of the proposed scheme. Simulation results verify the effectiveness of our derivations and demonstrate that the proposed system achieves better BER and security performances compared with the benchmark system, especially when the CSI is imperfect or unknown

Wireless networks physical layer security : modeling and performance characterization

Intrigued by the rapid growth and expand of wireless devices, data security is increasingly playing a significant role in our daily transactions and interactions with different entities. Possible examples, including e-healthcare information and online shopping, are becoming vulnerable due to the intrinsic nature of wireless transmission medium and the widespread open access of wireless links. Traditionally, the communication security is mainly regarded as the tasks at the upper layers of layered protocol stack, security techniques, including personal access control, password protection, and end-to-end encryption, have been widely studied in the open literature. More recently, plenty of research interests have been drawn to the physical layer forms of secrecy. As a new but appealing paradigm at physical layer, physical layer security is based on two pioneering works: (i) Shannon’s information-theoretic formulation and (ii) Wyner’s wiretap formulation. On account of the fundamental of physical layer security and the different nature of various wireless network, this dissertation is supposed to further fill the lacking of the existing research outcomes. To be specific, the contributions of this dissertation can be summarized as three-fold:(i) exploration of secrecy metrics to more general fading channels; (ii) characterization a new fading channel model and its reliability and security analysis in digital communication systems; and (iii) investigation of physical layer security over the random multiple-input multiple-output (MIMO) α −μ fading channels. Taking into account the classic Alice-Bob-Eve wiretap model, the first contribution can be divided into four aspects: (i) we have investigated the secrecy performance over single-input single-output (SISO) α −μ fading channels. The probability of non-zero (PNZ) secrecy capacity and the lower bound of secrecy outage probability (SOP) are derived for the special case when the main channel and wiretap channel undergo the same non-linearity fading parameter, i.e., α. Later on, for the purpose of filling the gap of lacking closed-form expression of SOP in the open literature and extending the obtained results in chapter 2 to the single-input multiple-output (SIMO) α − μ wiretap fading channels, utilizing the fact that the received signal-tonoise ratios (SNRs) at the legitimate receiver and eavesdropper can be approximated as new α −μ distributed random variables (RVs), the SOP metric is therefore derived, and given in terms of the bivariate Fox’s H-function; (ii) the secrecy performance over the Fisher-Snedecor F wiretap fading channels is initially considered. The SOP, PNZ, and ASC are finalized in terms of Meijer’s G-function; (iii) in order to generalize the obtained results over α −μ and Fisher-Snedecor F wiretap fading channels, a more flexible and general fading channel, i.e., Fox’s H-function fading model, are taken into consideration. Both the exact and asymptotic analysis of SOP, PNZ, and average secrecy capacity (ASC), are developed with closed-form expressions; and (iv) finally, motivated by the fact that the mixture gamma (MG) distribution is an appealing tool, which can be used to model the received instantaneous SNRs over wireless fading channels, the secrecy metrics over wiretap fading channels are derived based on the MG approach. Due to the limited transmission power and communication range, cooperative relays or multi-hop wireless networks are usually regarded as two promising means to address these concerns. Inspired by the obtained results in Chapters 2 and 3, the second main contribution is to propose a novel but simple fading channel model, namely, the cascaded α −μ. This new distribution is advantageous since it encompasses the existing cascaded Rayleigh, cascaded Nakagami-m, and cascaded Weibull with ease. Based on this, both the reliability and secrecy performance of a digital system over cascaded α −μ fading channels are further evaluated. Closed-form expressions of reliability metrics (including amount of fading (AF), outage probability, average channel capacity, and average symbol error probability (ABEP).) and secrecy metrics (including SOP, PNZ, and ASC) are respectively provided. Besides, their asymptotic behaviors are also performed and compared with the exact results. Considering the impacts of users’ densities, spatial distribution, and the path-loss exponent on secrecy issue, the third aspect of this thesis is detailed in Chapter 8 as the secrecy investigation of stochastic MIMO system over α −μ wiretap fading channels. Both the stochastic geometry and conventional space-time transmission (STT) scheme are used in the system configuration. The secrecy issue is mathematically evaluated by three metrics, i.e., connection outage, the probability of non-zero secrecy capacity and the ergodic secrecy capacity. Those three metrics are later on derived regarding two ordering scheme, and further compared with Monte-Carlo simulations