POWER-AWARE TECHNOLOGY MAPPING AND ROUTING FOR DUAL-VT FPGAS

Master'sMASTER OF ENGINEERIN

An FPGA Architecture and CAD Flow Supporting Dynamically Controlled Power Gating

© 2015 IEEE.Leakage power is an important component of the total power consumption in field-programmable gate arrays (FPGAs) built using 90-nm and smaller technology nodes. Power gating was shown to be effective at reducing the leakage power. Previous techniques focus on turning OFF unused FPGA resources at configuration time; the benefit of this approach depends on resource utilization. In this paper, we present an FPGA architecture that enables dynamically controlled power gating, in which FPGA resources can be selectively powered down at run-time. This could lead to significant overall energy savings for applications having modules with long idle times. We also present a CAD flow that can be used to map applications to the proposed architecture. We study the area and power tradeoffs by varying the different FPGA architecture parameters and power gating granularity. The proposed CAD flow is used to map a set of benchmark circuits that have multiple power-gated modules to the proposed architecture. Power savings of up to 83% are achievable for these circuits. Finally, we study a control system of a robot that is used in endoscopy. Using the proposed architecture combined with clock gating results in up to 19% energy savings in this application

Leakage Power Modeling and Reduction Techniques for Field Programmable Gate Arrays

FPGAs have become quite popular for implementing digital circuits and systems because of reduced costs and fast design cycles. This has led to increased complexity of FPGAs, and with technology scaling, many new challenges have come up for the FPGA industry, leakage power being one of the key challenges. The current generation FPGAs are being implemented in 90nm technology, therefore, managing leakage power in deep-submicron FPGAs has become critical for the FPGA industry to remain competitive in the semiconductor market and to enter the mobile applications domain. In this work an analytical state dependent leakage power model for FPGAs is developed, followed by dual-Vt based designs of the FPGA architecture for reducing leakage power. The leakage power model computes subthreshold and gate leakage in FPGAs, since these are the two dominant components of total leakage power in the scaled nanometer technologies. The leakage power model takes into account the dependency of gate and subthreshold leakage on the state of the circuit inputs. The leakage power model has two main components, one which computes the probability of a state for a particular FPGA circuit element, and the other which computes the leakage of the FPGA circuit element for a given input using analytical equations. This FPGA power model is particularly important for rapidly analyzing various FPGA architectures across different technology nodes. Dual-Vt based designs of the FPGA architecture are proposed, developed, and evaluated, for reducing the leakage power using a CAD framework. The logic and the routing resources of the FPGA are considered for dual-Vt assignment. The number of the logic elements that can be assigned high-Vt in the ideal case by using a dual-Vt assignment algorithm in the CAD framework is estimated. Based upon this estimate two kinds of architectures are developed and evaluated, homogeneous and heterogeneous architectures. Results indicate that leakage power savings of up to 50% can be obtained from these architectures. The analytical state dependent leakage power model developed has been used for estimating the leakage power savings from the dual-Vt FPGA architectures. The CAD framework that has been developed can also be used for developing and evaluating different dual-Vt FPGA architectures, other than the ones proposed in this work

Hybrid FPGA: Architecture and Interface

Hybrid FPGAs (Field Programmable Gate Arrays) are composed of general-purpose logic resources with different granularities, together with domain-specific coarse-grained units. This thesis proposes a novel hybrid FPGA architecture with embedded coarse-grained Floating Point Units (FPUs) to improve the floating point capability of FPGAs. Based on the proposed hybrid FPGA architecture, we examine three aspects to optimise the speed and area for domain-specific applications. First, we examine the interface between large coarse-grained embedded blocks (EBs) and fine-grained elements in hybrid FPGAs. The interface includes parameters for varying: (1) aspect ratio of EBs, (2) position of the EBs in the FPGA, (3) I/O pins arrangement of EBs, (4) interconnect flexibility of EBs, and (5) location of additional embedded elements such as memory. Second, we examine the interconnect structure for hybrid FPGAs. We investigate how large and highdensity EBs affect the routing demand for hybrid FPGAs over a set of domain-specific applications. We then propose three routing optimisation methods to meet the additional routing demand introduced by large EBs: (1) identifying the best separation distance between EBs, (2) adding routing switches on EBs to increase routing flexibility, and (3) introducing wider channel width near the edge of EBs. We study and compare the trade-offs in delay, area and routability of these three optimisation methods. Finally, we employ common subgraph extraction to determine the number of floating point adders/subtractors, multipliers and wordblocks in the FPUs. The wordblocks include registers and can implement fixed point operations. We study the area, speed and utilisation trade-offs of the selected FPU subgraphs in a set of floating point benchmark circuits. We develop an optimised coarse-grained FPU, taking into account both architectural and system-level issues. Furthermore, we investigate the trade-offs between granularities and performance by composing small FPUs into a large FPU. The results of this thesis would help design a domain-specific hybrid FPGA to meet user requirements, by optimising for speed, area or a combination of speed and area

CAD Techniques for Robust FPGA Design Under Variability

The imperfections in the semiconductor fabrication process and uncertainty in operating environment of VLSI circuits have emerged as critical challenges for the semiconductor industry. These are generally termed as process and environment variations, which lead to uncertainty in performance and unreliable operation of the circuits. These problems have been further aggravated in scaled nanometer technologies due to increased process variations and reduced operating voltage. Several techniques have been proposed recently for designing digital VLSI circuits under variability. However, most of them have targeted ASICs and custom designs. The flexibility of reconfiguration and unknown end application in FPGAs make design under variability different for FPGAs compared to ASICs and custom designs, and the techniques proposed for ASICs and custom designs cannot be directly applied to FPGAs. An important design consideration is to minimize the modifications in architecture and circuit to reduce the cost of changing the existing FPGA architecture and circuit. The focus of this work can be divided into three principal categories, which are, improving timing yield under process variations, improving power yield under process variations and improving the voltage profile in the FPGA power grid. The work on timing yield improvement proposes routing architecture enhancements along with CAD techniques to improve the timing yield of FPGA designs. The work on power yield improvement for FPGAs selects a low power dual-Vdd FPGA design as the baseline FPGA architecture for developing power yield enhancement techniques. It proposes CAD techniques to improve the power yield of FPGAs. A mathematical programming technique is proposed to determine the parameters of the buffers in the interconnect such as the sizes of the transistors and threshold voltage of the transistors, all within constraints, such that the leakage variability is minimized under delay constraints. Two CAD techniques are investigated and proposed to improve the supply voltage profile of the power grids in FPGAs. The first technique is a place and route technique and the second technique is a logic clustering technique to reduce IR-drops and spatial variation of supply voltage in the power grid

Fault and Defect Tolerant Computer Architectures: Reliable Computing With Unreliable Devices

This research addresses design of a reliable computer from unreliable device technologies. A system architecture is developed for a fault and defect tolerant (FDT) computer. Trade-offs between different techniques are studied and yield and hardware cost models are developed. Fault and defect tolerant designs are created for the processor and the cache memory. Simulation results for the content-addressable memory (CAM)-based cache show 90% yield with device failure probabilities of 3 x 10(-6), three orders of magnitude better than non fault tolerant caches of the same size. The entire processor achieves 70% yield with device failure probabilities exceeding 10(-6). The required hardware redundancy is approximately 15 times that of a non-fault tolerant design. While larger than current FT designs, this architecture allows the use of devices much more likely to fail than silicon CMOS. As part of model development, an improved model is derived for NAND Multiplexing. The model is the first accurate model for small and medium amounts of redundancy. Previous models are extended to account for dependence between the inputs and produce more accurate results

Design Methodologies and CAD Tools for Leakage Power Optimization in FPGAs

The scaling of the CMOS technology has precipitated an exponential increase in both subthreshold and gate leakage currents in modern VLSI designs. Consequently, the contribution of leakage power to the total chip power dissipation for CMOS designs is increasing rapidly, which is estimated to be 40% for the current technology generations and is expected to exceed 50% by the 65nm CMOS technology. In FPGAs, the power dissipation problem is further aggravated when compared to ASIC designs because FPGA use more transistors per logic function when compared to ASIC designs. Consequently, solving the leakage power problem is pivotal to devising power-aware FPGAs in the nanometer regime. This thesis focuses on devising both architectural and CAD techniques for leakage mitigation in FPGAs. Several CAD and architectural modifications are proposed to reduce the impact of leakage power dissipation on modern FPGAs. Firstly, multi-threshold CMOS (MTCMOS) techniques are introduced to FPGAs to permanently turn OFF the unused resources of the FPGA, FPGAs are characterized with low utilization percentages that can reach 60%. Moreover, such architecture enables the dynamic shutting down of the FPGA idle parts, thus reducing the standby leakage significantly. Employing the MTCMOS technique in FPGAs requires several changes to the FPGA architecture, including the placement and routing of the sleep signals and the MTCMOS granularity. On the CAD level, the packing and placement stages are modified to allow the possibility of dynamically turning OFF the idle parts of the FPGA. A new activity generation algorithm is proposed and implemented that aims to identify the logic blocks in a design that exhibit similar idleness periods. Several criteria for the activity generation algorithm are used, including connectivity and logic function. Several versions of the activity generation algorithm are implemented to trade power savings with runtime. A newly developed packing algorithm uses the resulting activities to minimize leakage power dissipation by packing the logic blocks with similar or close activities together. By proposing an FPGA architecture that supports MTCMOS and developing a CAD tool that supports the new architecture, an average power savings of 30% is achieved for a 90nm CMOS process while incurring a speed penalty of less than 5%. This technique is further extended to provide a timing-sensitive version of the CAD flow to vary the speed penalty according to the criticality of each logic block. Secondly, a new technique for leakage power reduction in FPGAs based on the use of input dependency is developed. Both subthreshold and gate leakage power are heavily dependent on the input state. In FPGAs, the effect of input dependency is exacerbated due to the use of pass-transistor multiplexer logic, which can exhibit up to 50% variation in leakage power due to the input states. In this thesis, a new algorithm is proposed that uses bit permutation to reduce subthreshold and gate leakage power dissipation in FPGAs. The bit permutation algorithm provides an average leakage power reduction of 40% while having less than 2% impact on the performance and no penalty on the design area. Thirdly, an accurate probabilistic power model for FPGAs is developed to quantify the savings from the proposed leakage power reduction techniques. The proposed power model accounts for dynamic, short circuit, and leakage power (including both subthreshold and gate leakage power) dissipation in FPGAs. Moreover, the power model accounts for power due to glitches, which accounts for almost 20% of the dynamic power dissipation in FPGAs. The use of probabilities in the power model makes it more computationally efficient than the other FPGA power models in the literature that rely on long input sequence simulations. One of the main advantages of the proposed power model is the incorporation of spatial correlation while estimating the signal probability. Other probabilistic FPGA power models assume spatial independence among the design signals, thus overestimating the power calculations. In the proposed model, a probabilistic model is proposed for spatial correlations among the design signals. Moreover, a different variation is proposed that manages to capture most of the spatial correlations with minimum impact on runtime. Furthermore, the proposed power model accounts for the input dependency of subthreshold and gate leakage power dissipation. By comparing the proposed power model to HSpice simulation, the estimated power is within 8% and is closer to HSpice simulations than other probabilistic FPGA power models by an average of 20%

A framework to explore low-power architecture and variability-aware timing estimation of FPGAs

Master'sMASTER OF ENGINEERIN

A Finite Domain Constraint Approach for Placement and Routing of Coarse-Grained Reconfigurable Architectures

Scheduling, placement, and routing are important steps in Very Large Scale Integration (VLSI) design. Researchers have developed numerous techniques to solve placement and routing problems. As the complexity of Application Specific Integrated Circuits (ASICs) increased over the past decades, so did the demand for improved place and route techniques. The primary objective of these place and route approaches has typically been wirelength minimization due to its impact on signal delay and design performance. With the advent of Field Programmable Gate Arrays (FPGAs), the same place and route techniques were applied to FPGA-based design. However, traditional place and route techniques may not work for Coarse-Grained Reconfigurable Architectures (CGRAs), which are reconfigurable devices offering wider path widths than FPGAs and more flexibility than ASICs, due to the differences in architecture and routing network. Further, the routing network of several types of CGRAs, including the Field Programmable Object Array (FPOA), has deterministic timing as compared to the routing fabric of most ASICs and FPGAs reported in the literature. This necessitates a fresh look at alternative approaches to place and route designs. This dissertation presents a finite domain constraint-based, delay-aware placement and routing methodology targeting an FPOA. The proposed methodology takes advantage of the deterministic routing network of CGRAs to perform a delay aware placement