A 100-MIPS GaAs asynchronous microprocessor

The authors describe how they ported an asynchronous microprocessor previously implemented in CMOS to gallium arsenide, using a technology-independent asynchronous design technique. They introduce new circuits including a sense-amplifier, a completion detection circuit, and a general circuit structure for operators specified by production rules. The authors used and tested these circuits in a variety of designs

Exploration and Design of High Performance Variation Tolerant On-Chip Interconnects

Siirretty Doriast

Asynchronous design of a multi-dimensional logarithmic number system processor for digital hearing instruments.

This thesis presents an asynchronous Multi-Dimensional Logarithmic Number System (MDLNS) processor that exhibits very low power dissipation. The target application is for a hearing instrument DSP. The MDLNS is a newly developed number system that has the advantage of reducing hardware complexity compared to the classical Logarithmic Number System (LNS). A synchronous implementation of a 2-digit 2DLNS filterbank, using the MDLNS to construct a FIR filterbank, has successfully proved that this novel number representation can benefit this digital hearing instrument application in the requirement of small size and low power. In this thesis we demonstrate that the combination of using the MDLNS, along with an asynchronous design methodology, produces impressive power savings compared to the previous synchronous design. A 4-phase bundled-data full-handshaking protocol is applied to the asynchronous control design. We adopt the Differential Cascade Voltage Switch Logic (DCVSL) circuit family for the design of the computation cells in this asynchronous MDLNS processor. Besides the asynchronous design methodology, we also use finite ring calculations to reduce adder bit-width to provide improvements compared to the previous MDLNS filterbank architecture. Spectre power simulation results from simulations of this asynchronous MDLNS processor demonstrate that over 70 percent power savings have been achieved compared to the synchronous design. This full-custom asynchronous MDLNS processor has been submitted for fabrication in the TSMC 0.18mum CMOS technology. A further contribution in this thesis is the development of a novel synchronizing method of design for testability (DfT), which is offered as a possible solution for asynchronous DfT methods.Dept. of Electrical and Computer Engineering. Paper copy at Leddy Library: Theses & Major Papers - Basement, West Bldg. / Call Number: Thesis2004 .W85. Source: Masters Abstracts International, Volume: 43-01, page: 0288. Advisers: G. A. Jullien; W. C. Miller. Thesis (M.A.Sc.)--University of Windsor (Canada), 2004

Doctor of Philosophy

dissertationCommunication surpasses computation as the power and performance bottleneck in forthcoming exascale processors. Scaling has made transistors cheap, but on-chip wires have grown more expensive, both in terms of latency as well as energy. Therefore, the need for low energy, high performance interconnects is highly pronounced, especially for long distance communication. In this work, we examine two aspects of the global signaling problem. The first part of the thesis focuses on a high bandwidth asynchronous signaling protocol for long distance communication. Asynchrony among intellectual property (IP) cores on a chip has become necessary in a System on Chip (SoC) environment. Traditional asynchronous handshaking protocol suffers from loss of throughput due to the added latency of sending the acknowledge signal back to the sender. We demonstrate a method that supports end-to-end communication across links with arbitrarily large latency, without limiting the bandwidth, so long as line variation can be reliably controlled. We also evaluate the energy and latency improvements as a result of the design choices made available by this protocol. The use of transmission lines as a physical interconnect medium shows promise for deep submicron technologies. In our evaluations, we notice a lower energy footprint, as well as vastly reduced wire latency for transmission line interconnects. We approach this problem from two sides. Using field solvers, we investigate the physical design choices to determine the optimal way to implement these lines for a given back-end-of-line (BEOL) stack. We also approach the problem from a system designer's viewpoint, looking at ways to optimize the lines for different performance targets. This work analyzes the advantages and pitfalls of implementing asynchronous channel protocols for communication over long distances. Finally, the innovations resulting from this work are applied to a network-on-chip design example and the resulting power-performance benefits are reported

Study and implementation of a PVT insensitive CMOS oscillator

Fallières Armand. Circulaire adressée aux Préfets, au sujet du classement des instituteurs. In: Bulletin administratif de l'instruction publique. Tome 47 n°891, 1890. pp. 137-138

Analysis of Parameter Tuning on Energy Efficiency in Asynchronous Circuits

Power and energy consumption are the primary concern of the digital integrated circuit (IC) industry. Asynchronous logic, in the past several years, has increased in popularity due to its low power nature. This thesis analyzes a collection of array multipliers with different parameters to compare two asynchronous design paradigms, NULL Convention Logic (NCL) and Multi-Threshold NULL Convention Logic (MTNCL). Several commercially available pieces of software and custom scripts are used to analyze the asynchronous circuits and their components to provide the energy consumption estimation on various parts of each circuit. The analysis of the software results revealed that MTNCL circuits are more energy efficient for any size provided the number of pipeline stages does not become too great. Otherwise NCL would consume less energy. A combinational logic gate count to register gate count ratio of 3 was given to help determine when an MTNCL circuit would have too many pipeline stages for circuits designed with IBM\u27s 130nm 8RF-DM design kit

A self-referenced single-electron current source

[no abstract