Low-Complexity Equalisers for Offset Constellations in Massive MIMO Schemes

This work was supported in part by the European Regional Development Fund (FEDER), through the Competitiveness and Internationalization Operational Program of the Portugal 2020 Framework, in part by the Regional OP Centro under Grant POCI-01-0145-FEDER-030588, in part by the Regional OP Lisboa under Grant Lisboa-01-0145-FEDER-03058, in part by the FCT/MEC through national funds of MASSIVE5G Project under Grant SAICT-45-2017-02 and PES3N Project under Grant 2018-SAICT-45-2017-POCI-01-0145-FEDER-030629, in part by the UID/EEE/50008/2019 Project, and in part by the FCT Ph.D. under Grant SFRH/BD/108522/2015.Massive multi-input-multi-output (m-MIMO) schemes require low-complexity implementations at both the transmitter and the receiver side, especially for systems operation at millimeter wave (mmWave) bands. In this paper, we consider the use of offset constellations in m-MIMO systems operating at mmWave frequencies. These signals are designed to have either an almost constant envelope or be decomposed as the sum of constant-envelope signals, making them compatible with strongly nonlinear power amplifiers, which can have low-implementation complexity and high amplification efficient, making them particularly interesting for mmWave communications. We design and evaluate low-complexity frequency-domain receivers for offset signals. It is shown that the proposed receivers can have excellent performance/complexity trade-offs in m-MIMO scenarios, making them particularly interesting for future wireless systems operating at mmWave bands.publishersversionpublishe

Spectral Efficiency Optimization in Flexi-Grid Long-Haul Optical Systems

Flexible grid optical networks allow a better exploitation of fiber capacity, by enabling a denser frequency allocation. A tighter channel spacing, however, requires narrower filters, which increase linear intersymbol interference (ISI), and may dramatically reduce system reach. Commercial coherent receivers are based on symbol by symbol detectors, which are quite sensitive to ISI. In this context, Nyquist spacing is considered as the ultimate limit to wavelength-division multiplexing (WDM) packing. In this paper, we show that by introducing a limited-complexity trellis processing at the receiver, either the reach of Nyquist WDM flexi-grid networks can be significantly extended, or a denser-than-Nyquist channel packing (i.e., a higher spectral efficiency (SE)) is possible at equal reach. By adopting well-known information-theoretic techniques, we design a limited-complexity trellis processing and quantify its SE gain in flexi-grid architectures where wavelength selective switches over a frequency grid of 12.5GHz are employed.Comment: 7 pages, 9 figure

Synchronisation, détection et égalisation de modulation à phase continue dans des canaux sélectifs en temps et en fréquence

Si les drones militaires connaissent un développement important depuis une quinzaine d’année, suivi depuis quelques années par les drones civiles dont les usages ne font que se multiplier, en réalité les drones ont un siècle avec le premier vol d’un avion équipé d’un système de pilotage automatique sur une centaine de kilomètre en 1918. La question des règles d’usage des drones civiles sont en cours de développement malgré leur multiplication pour des usages allant de l’agriculture, à l’observation en passant par la livraison de colis. Ainsi, leur intégration dans l’espace aérien reste un enjeu important, ainsi que les standards de communication avec ces drones dans laquelle s’inscrit cette thèse. Cette thèse vise en effet à étudier et proposer des solutions pour les liens de communications des drones par satellite.L’intégration de ce lien de communication permet d’assurer la fiabilité des communications et particulièrement du lien de Commande et Contrôle partout dans le monde, en s’affranchissant des contraintes d’un réseau terrestre (comme les zones blanches). En raison de la rareté des ressources fréquentielles déjà allouées pour les futurs systèmes intégrant des drones, l’efficacité spectrale devient un paramètre important pour leur déploiement à grande échelle et le contexte spatiale demande l’utilisation d’un système de communication robuste aux non-linéarités. Les Modulations à Phase Continue permettent de répondre à ces problématiques. Cependant, ces dernières sont des modulations non-linéaire à mémoire entraînant une augmentation de la complexité des récepteurs. Du fait de la présence d’un canal multi-trajet (canal aéronautique par satellite), le principal objectif de cette thèse est de proposer des algorithmes d’égalisation (dans le domaine fréquentiel pour réduire leur complexité) et de synchronisation pour CPM adaptés à ce concept tout en essayant de proposer une complexité calculatoire raisonnable. Dans un premier temps, nous avons considéré uniquement des canaux sélectifs en fréquence et avons étudier les différents égaliseurs de la littérature. En étudiant leur similitudes et différences, nous avons pu développer un égaliseur dans le domaine fréquentiel qui proposant les mêmes performances a une complexité moindre. Nous proposons également des méthodes d’estimation canal et une méthode d’estimation conjointe du canal et de la fréquence porteuse. Dans un second temps nous avons montré comment étendre ces méthodes à des canaux sélectifs en temps et fréquence permettant ainsi de conserver une complexité calculatoire raisonnable

Linear amplification with multiple nonlinear devices

Dissertação para obtenção do Grau de Mestre em Engenharia Electrotécnica e ComputadoresIn mobile wireless systems, where there are strict power and bandwidth constrains it is desirable to adopt energy efficient constellations combined with powerful equalizer. However, this increased spectral efficiency of multilevel modulations comes at the expense of reduced power efficiency, which is undesirable in systems where power consumption is a constraint. Hence, minimization of the transmitted energy would enable a significant reduction in the total energy consumption of the wireless mobile devices. A simple and practical constellation optimization design would optimize the transmitted energy with a minimum increase in system complexity. The constellation decomposition in terms of a sum of BPSK (Bi-Phase Shift Keying) sub-constellations, relies on an analytical characterization of the mapping rule were the constellation symbols are written as a linear function of the transmitted bits. Moreover, large constellations in general and non-uniform constellations in particular are very sensitive to interference, namely the residual ISI (Inter-Symbol Interference) at the output of a practical equalizer that does not invert completely the channel effects. IB-DFE(Iterative Block DFE) is a promising iterative frequency domain equalization technique for SC-FDE schemes (Single-Carrier with Frequency Domain Equalization) that allows excellent performance. Therefore it is possible to use the decomposition of constellations on BPSK components to define a pragmatic method for designing IB-DFE receivers that can be employed with any constellation. In this thesis we consider SC-DFE schemes based on high orderM-ary energy optimized constellations with IB-DFE receivers. It is proposed a method for designing the receiver that does not require a significant increase in system complexity and can be used for the computation of the receiver parameters for any constellation. This method is then employed to design iterative receivers, implemented in the frequency-domain, which can cope with higher sensitivity to ISI effects of the constellations resulting from the energy optimization process.Fundação para a Ciência e Tecnologia - MPSat (PTDC/EEA-TEL/099074/2008) projec

Pilot sequence based IQ imbalance estimation and compensation

Abstract. As modern radio access technologies strive to achieve progressively higher data rates and to become increasingly more reliable, minimizing the effects of hardware imperfections becomes a priority. One of those imperfections is in-phase quadrature imbalance (IQI), caused by amplitude and phase response differences between the I and Q branches of the IQ demodulation process. IQI has been shown to deteriorate bit error rates, possibly compromise positioning performance, amongst other effects. Minimizing IQI by tightening hardware manufacturing constraints is not always a commercially viable approach, thus, baseband processing for IQI compensation provides an alternative. The thesis begins by presenting a study in IQI modeling for direct conversion receivers, we then derive a model for general imbalances and show that it reproduces the two most common models in the bibliography. We proceed by exploring some of the existing IQI compensation techniques and discussing their underlying assumptions, advantages, and possible relevant issues. A novel pilot-sequence based approach for tackling IQI estimation and compensation is introduced in this thesis. The idea is to minimize the square Frobenius norm of the error between candidate covariance matrices, which are functions of the candidate IQI parameters, and the sample covariance matrices, obtained from measurements. This new method is first presented in a positioning context with flat fading channels, where IQI compensation is used to improve the positioning estimates mean square error. The technique is then adapted to orthogonal frequency division multiplexing (OFDM) systems,including an version that exploits the 5G New Radio reference signals to estimate the IQI coefficients. We further generalize the new approach to solve joint transmitter and receiver IQI estimation and discuss the implementation details and suggested optimization techniques. The introduced methods are evaluated numerically in their corresponding chapters under a set of different conditions, such as varying signal-to-noise ratio, pilot sequence length, channel model, number of subcarriers, etc. Finally, the proposed compensation approach is compared to other well-established methods by evaluating the bit error rate curves of 5G transmissions. We consistently show that the proposed method is capable of outperforming these other methods if the SNR and pilot sequence length values are sufficiently high. In the positioning simulations, the proposed IQI compensation method was able to improve the root mean squared error (RMSE) of the position estimates by approximately 25 cm. In the OFDM scenario, with high SNR and a long pilot sequence, the new method produced estimates with mean squared error (MSE) about a million times smaller than those from a blind estimator. In bit error rate (BER) simulations, the new method was the only compensation technique capable of producing BER curves similar to the curves without IQI in all of the studied scenarios

Single-Frequency Network Terrestrial Broadcasting with 5GNR Numerology

L'abstract è presente nell'allegato / the abstract is in the attachmen

Software Defined Radio Implementation Of Ds-Cdma In Inter-Satellite Communications For Small Satellites

The increased usage of CubeSats recently has changed the communication philosophy from long-range point-to-point propagations to a multi-hop network of small orbiting nodes. Separating system tasks into many dispersed satellites can increase system survivability, versatility, configurability, adaptability, and autonomy. Inter-satellite links (ISL) enable the satellites to exchange information and share resources while reducing the traffic load to the ground. Establishment and stability of the ISL are impacted by factors such as the satellite orbit and attitude, antenna configuration, constellation topology, mobility, and link range. Software Defined Radio (SDR) is beginning to be heavily used in small satellite communications for applications such as base stations. A software-defined radio is a software program that does the functionality of a hardware system. The digital signal processing blocks are incorporated into the software giving it more flexibility and modulation. With this, the idea of a remote upgrade from the ground as well as the potential to accommodate new applications and future services without hardware changes is very promising. Realizing this, my idea is to create an inter-satellite link using software defined radio. The advantages of this are higher data rates, modification of operating frequencies, possibility of reaching higher frequency bands for higher throughputs, flexible modulation, demodulation and encoding schemes, and ground modifications. However, there are several challenges in utilizing the software-defined radio to create an inter-satellite link communication for small satellites. In this paper, we designed and implemented a multi-user inter-satellite communication network using SDRs, where Code Division Multiple Access (CDMA) technique is utilized to manage the multiple accesses to shared communication channel among the satellites. This model can be easily reconfigured to support any encoding/decoding, modulation, and other signal processing schemes

Software Defined Radio Implementation Of Ds-Cdma In Inter-Satellite Communications For Small Satellites

The increased usage of CubeSats recently has changed the communication philosophy from long-range point-to-point propagations to a multi-hop network of small orbiting nodes. Separating system tasks into many dispersed satellites can increase system survivability, versatility, configurability, adaptability, and autonomy. Inter-satellite links (ISL) enable the satellites to exchange information and share resources while reducing the traffic load to the ground. Establishment and stability of the ISL are impacted by factors such as the satellite orbit and attitude, antenna configuration, constellation topology, mobility, and link range. Software Defined Radio (SDR) is beginning to be heavily used in small satellite communications for applications such as base stations. A software-defined radio is a software program that does the functionality of a hardware system. The digital signal processing blocks are incorporated into the software giving it more flexibility and modulation. With this, the idea of a remote upgrade from the ground as well as the potential to accommodate new applications and future services without hardware changes is very promising. Realizing this, my idea is to create an inter-satellite link using software defined radio. The advantages of this are higher data rates, modification of operating frequencies, possibility of reaching higher frequency bands for higher throughputs, flexible modulation, demodulation and encoding schemes, and ground modifications. However, there are several challenges in utilizing the software-defined radio to create an inter-satellite link communication for small satellites. In this paper, we designed and implemented a multi-user inter-satellite communication network using SDRs, where Code Division Multiple Access (CDMA) technique is utilized to manage the multiple accesses to shared communication channel among the satellites. This model can be easily reconfigured to support any encoding/decoding, modulation, and other signal processing schemes

Améliorations des transmissions VLC (Visible Light Communication) sous contrainte d'éclairage : études théoriques et expérimentations

Abstract : Indoor visible light communication (VLC) networks based on light-emitting diodes (LEDs) currently enjoy growing interest thanks in part to their robustness against interference, wide license-free available bandwidth, low cost, good energy efficiency and compatibility with existing lighting infrastructure. In this thesis, we investigate spectral-efficient modulation techniques for the physical layer of VLC to increase throughput while considering the quality of illumination as well as implementation costs. Numerical and experimental studies are performed employing pulse amplitude modulation (PAM) and carrierless amplitude and phase (CAP) modulation under illumination constraints and for high modulation orders. Furthermore, the impact of LED nonlinearity is investigated and a postdistortion technique is evaluated to compensate these nonlinear effects. Within this framework, transmission rates in the order of a few hundred Mb/s are achieved using a test bench made of low-cost components. In addition, an imaging multiple input multiple-output (MIMO) system is developed and the impact on performance of imaging lens misalignment is theoretically and numerically assessed. Finally, a polynomial matrix decomposition technique based on the classical LU factorization method is studied and applied for the first time to MIMO VLC systems in large space indoor environments.Les réseaux de communication en lumière visible (VLC) s’appuyant sur l’utilisation de diodes électroluminescentes (LED) bénéficient actuellement d’un intérêt grandissant, en partie grâce à leur robustesse face aux interférences électromagnétiques, leur large bande disponible non-régulée, leur faible coût, leur bonne efficacité énergétique, ainsi que leur compatibilité avec les infrastructures d’éclairage déjà existantes. Dans cette thèse, nous étudions des techniques de modulation à haute efficacité spectrale pour la couche physique des VLC pour augmenter les débits tout en considérant la qualité de l’éclairage ainsi que les coûts d’implémentation. Des études numériques et expérimentales sont réalisées sur la modulation d’impulsion d’amplitude (PAM) et sur la modulation d’amplitude et de phase sans porteuse (CAP) sous des contraintes d’éclairage et pour des grands ordres de modulation. De plus, l’impact des non-linéarités de la LED est étudié et une technique de post-distorsion est évaluée pour corriger ces effets non-linéaires. Dans ce cadre, des débits de plusieurs centaines de Mb/s sont atteints en utilisant un banc de test réalisé à partir de composants à bas coûts. Par ailleurs, un système multi-entrées multi-sorties (MIMO) imageant est également développé et l’impact du désaxage de l’imageur sur les performances est étudié. Finalement, une technique de décomposition polynomiale basée sur la méthode de factorisation classique LU est étudiée et appliquée aux systèmes MIMO VLC dans des grands espaces intérieurs