AC voltage regulation of a bidirectional high-frequency link converter using a deadbeat controller

This paper presents a digital controller for AC voltage regulation of a bidirectional high-frequency link (BHFL) inverter using Deadbeat control. The proposed controller consists of inner current loop, outer voltage loop and a feed-forward controller, which imposes a gain scheduling effect according to the reference signal to compensate the steady-state error of the system. The main property of the proposed controller is that the current- and the voltage-loop controllers have the same structure, and use the same sampling period. This simplifies the design and implementation processes. To improve the overall performance of the system, additional disturbance decoupling networks are employed. This takes into account the model discretization effect. Therefore, accurate disturbance decoupling can be achieved, and the system robustness towards load variations is increased. To avoid transformer saturation due to low frequency voltage envelopes, an equalized pulse width modulation (PWM) technique has been introduced. The proposed controller has been realized using the DS1104 digital signal processor (DSP) from dSPACE. Its performances have been tested on a one kVA prototype inverter. Experimental results showed that the proposed controller has very fast dynamic and good steady-state responses even under highly nonlinear loads

Insights into dynamic tuning of magnetic-resonant wireless power transfer receivers based on switch-mode gyrators

Magnetic-resonant wireless power transfer (WPT) has become a reliable contactless source of power for a wide range of applications. WPT spans different power levels ranging from low-power implantable devices up to high-power electric vehicles (EV) battery charging. The transmission range and efficiency of WPT have been reasonably enhanced by resonating the transmitter and receiver coils at a common frequency. Nevertheless, matching between resonance in the transmitter and receiver is quite cumbersome, particularly in single-transmitter multi-receiver systems. The resonance frequency in transmitter and receiver tank circuits has to be perfectly matched, otherwise power transfer capability is greatly degraded. This paper discusses the mistuning effect of parallel-compensated receivers, and thereof a novel dynamic frequency tuning method and related circuit topology and control is proposed and characterized in the system application. The proposed method is based on the concept of switch-mode gyrator emulating variable lossless inductors oriented to enable self-tunability in WPT receiversPeer ReviewedPostprint (published version

Design Optimization of Inductive Power Transfer Systems for Contactless Electric Vehicle Charging Applications

Contactless Electric Vehicle (EV) charging based on magnetic resonant induction is an emerging technology that can revolutionize the future of the EV industry and transportation systems by enabling an automated and convenient charging process. However, in order to make this technology an acceptable alternative for conventional plug-in charging systems it needs to be optimized for different design measures. Specifically, the efficiency of an inductive EV charging system is of a great importance and should be comparable to the efficiency of conventional plug-in EV chargers. The aim of this study is to develop solutions that contribute to the design enhancement of inductive EV charging systems. Specifically, generalized physics-based design optimization methods that address the trade-off problem between several key objectives including efficiency, power density, misalignment tolerance, and cost efficiency considering critical constraints are developed. Using the developed design methodology, a 3.7kW inductive charging system with square magnetic structures is investigated as a case study and a prototype is built to validate the optimization results. The developed prototype achieves 93.65% efficiency (DC-to-DC) and a power density of 1.65kW/dm3. Also, self-tuning power transfer control methods with resonance frequency tracking capability and bidirectional power transfer control are presented. The proposed control methods enhance the efficiency of power converters and reduce the Electromagnetic Interference (EMI) by enabling soft-switching operations. Several simplified digital controllers are developed and experimentally implemented. The controllers are implemented without the use of DSP/FPGA solutions. Experimental tests show that of the developed simplified controllers can effectively regulate the power transfer around the desired value. Moreover, the experiments show that compared to conventional converters, the developed converters can achieve 4% higher efficiency at low power levels. Moreover, enhanced matrix converter topologies that can achieve bidirectional power transfer and high efficiency with a reduced number of switching elements are introduced. The self-tuning controllers are utilized to design and develop control schemes for bidirectional power transfer regulation. The simulation analyses and experimental results show that the developed matrix converters can effectively establish bidirectional power transfer at the desired power levels with soft-switching operations and resonance frequency tracking capability. Specifically, a direct three-phase AC-AC matrix converter with a reduced number of switches (only seven) is developed and built. It is shown that the developed converters can achieve efficiencies as high as 98.54% at high power levels and outperform conventional two-stage converters

Design of Inductive Power Transfer (IPT) for Low-Power Application

Inductive power transfer (IPT) is preferred for numerous applications nowadays, ranging from microwatt bio-engineering devices to high power battery charging system. IPT system is based on the basic concept of electromagnetics induction which able to transfer the power from a source of electrical to the load without using any type of physical interconnection. This paper present a low-cost designed and implementation of IPT system via magnetic resonant coupling. NI Multisim 14.0 software was used to simulate the circuit diagram and the hardware prototype was developed for testing

Robust and fast sliding-mode control for a DC-DC current-source parallel-resonant converter

Modern DC-DC resonant converters are normally built around a voltage-source series-resonant converter. This study aims to facilitate the practical use of current-source parallel-resonant converters due to their outstanding properties. To this end, this study presents a sliding-mode control scheme, which provides the following features to the closed-loop system: (i) high robustness to external disturbances and parameter variations and (ii) fast transient response during large and abrupt load changes. In addition, a design procedure for determining the values of the control parameters is presented. The theoretical contributions of this study are experimentally validated by selected tests on a laboratory prototype.Peer ReviewedPreprin

Bidirectional Electric Vehicles Service Integration in Smart Power Grid with Renewable Energy Resources

As electric vehicles (EVs) become more popular, the utility companies are forced to increase power generations in the grid. However, these EVs are capable of providing power to the grid to deliver different grid ancillary services in a concept known as vehicle-to-grid (V2G) and grid-to-vehicle (G2V), in which the EV can serve as a load or source at the same time. These services can provide more benefits when they are integrated with Photovoltaic (PV) generation. The proper modeling, design and control for the power conversion systems that provide the optimum integration among the EVs, PV generations and grid are investigated in this thesis. The coupling between the PV generation and integration bus is accomplished through a unidirectional converter. Precise dynamic and small-signal models for the grid-connected PV power system are developed and utilized to predict the system’s performance during the different operating conditions. An advanced intelligent maximum power point tracker based on fuzzy logic control is developed and designed using a mix between the analytical model and genetic algorithm optimization. The EV is connected to the integration bus through a bidirectional inductive wireless power transfer system (BIWPTS), which allows the EV to be charged and discharged wirelessly during the long-term parking, transient stops and movement. Accurate analytical and physics-based models for the BIWPTS are developed and utilized to forecast its performance, and novel practical limitations for the active and reactive power-flow during G2V and V2G operations are stated. A comparative and assessment analysis for the different compensation topologies in the symmetrical BIWPTS was performed based on analytical, simulation and experimental data. Also, a magnetic design optimization for the double-D power pad based on finite-element analysis is achieved. The nonlinearities in the BIWPTS due to the magnetic material and the high-frequency components are investigated rely on a physics-based co-simulation platform. Also, a novel two-layer predictive power-flow controller that manages the bidirectional power-flow between the EV and grid is developed, implemented and tested. In addition, the feasibility of deploying the quasi-dynamic wireless power transfer technology on the road to charge the EV during the transient stops at the traffic signals is proven

Vehicle-to-grid (V2G) Reactive Power Operation Analysis of the EV/PHEV Bidirectional Battery Charger

More battery powered electric vehicles (EVs) and plug-in hybrid electric vehicles (PHEVs) will be introduced to the market in 2013 and beyond. Since these vehicles have large batteries that need to be charged from an external power source or directly from the grid, their charging circuits and grid interconnection issues are garnering more attention. It is possible to incorporate more than one operation mode in a charger by allowing the power to flow bidirectionally. Usually, the bidirectional power transfer stands for two-way transfer of active power between the charger and the grid. The general term of sending active power from the vehicle to the grid is called vehicle to grid (V2G). While plug-in electric vehicles (PEVs) potentially have the capability to fulfill the energy storage needs of the electric grid, the degradation on the battery during this operation makes it less preferable by the auto manufacturers and consumers. On the other hand, the on-board chargers can also supply energy storage system applications such as reactive power compensation, voltage regulation, and power factor correction without the need of engaging the battery with the grid and thereby preserving its lifetime. This study shows the effect of reactive power operation on the design and operation of single-phase on-board chargers that are suitable for reactive power support. It further introduces a classification of single-phase ac-dc converters that can be used in on-board PEV chargers based on their power transfer capabilities in addition to the currently available surveys. The cost of supplying reactive power is also important to effectively evaluate reactive power operation using chargers. There are two major impacts: one is on the converter design (incremental costs) and the other is on the operating electricity costs. Their combination shows the total effect and cost of reactive power operation and can be compared with other options of the utility grid to supply reactive power. Two customer scenarios are investigated to have two options of reactive power support. Level 1 and Level 2 reactive power support are evaluated separately

Communication‐less Synchronous Rectification for In Motion Wireless Charging

This thesis puts forward a control scheme to allow for synchronous rectification for dynamic wireless power transfer. The automotive industry is transitioning away from internal combustion engines (ICEs) and towards electric vehicles (EVs). This transition is spurred by the environmental and economic benefits EVs offer over ICEs. However, further improvements can still be made to how electric vehicles operate. One of these improvements is the technology of in motion wireless charging or dynamic wireless power transfer. In motion wireless charging offers the ability to remove existing range anxiety concerns for EVs. It also offers the potential for a reduction in battery sizes for EVs, which are the primary cost of EVs, this in turn decreases the total costs of mass EV adoption. Traditional implementations of in motion wireless charging utilize passive rectification to simplify controls between embedded primary pads and the vehicle. However, this solution while effective, limits the potential benefits of wireless charging. The use of synchronous or active rectification techniques, offer improved performance, control techniques, and bidirectional capabilities. However, the reason synchronous rectification is not already used in in motion charging is the complexity of synchronization over wireless communication. To move past this challenge, this thesis investigates a synchronization scheme that can be achieved without communication by taking advantage of induced free resonant currents in the vehicle’s tuning network to synchronize the switching transitions to receive power. In this thesis a traditional in motion wireless charging system utilizing passive rectification is designed and built as a benchmark for dynamic charging. Simulations of this control scheme are presented. Practical considerations are addressed for hardware realization. Finally, the control approach is validated through hardware in static and dynamic applications

Sensitivity Analysis of a Bidirectional Wireless Charger for EV

Bidirectional chargers are required to fully integrate Electric Vehicle (EV) into the smart grids. Additionally, wireless chargers ease the charge/discharge process of the EV batteries so that they are becoming more popular to fulfill a V2G scenario. When considering the load of wireless chargers, it is a requirement to know the real output power that these systems offer. The designed output power may differ from the real one as components suffer from tolerance. This paper defines six sensitivity factors to model the severity of the effects of tolerance into the output power. To do so, an electric circuit analysis is used and a mathematical formulation is derived. The six sensitivity factors are computed for a laboratory prototype.Universidad de Málaga. Campus de Excelencia Internacional Andalucía Tech

Model and Design of a Power Driver for Piezoelectric Stack Actuators

A power driver has been developed to control piezoelectric stack actuators used in automotive application. A FEM model of the actuator has been implemented starting from experimental characterization of the stack and mechanical and piezoelectric parameters. Experimental results are reported to show a correct piezoelectric actuator driving method and the possibility to obtain a sensor-less positioning contro