MORA - an architecture and programming model for a resource efficient coarse grained reconfigurable processor

This paper presents an architecture and implementation details for MORA, a novel coarse grained reconfigurable processor for accelerating media processing applications. The MORA architecture involves a 2-D array of several such processors, to deliver low cost, high throughput performance in media processing applications. A distinguishing feature of the MORA architecture is the co-design of hardware architecture and low-level programming language throughout the design cycle. The implementation details for the single MORA processor, and benchmark evaluation using a cycle accurate simulator are presented

A high speed Tri-Vision system for automotive applications

Purpose: Cameras are excellent ways of non-invasively monitoring the interior and exterior of vehicles. In particular, high speed stereovision and multivision systems are important for transport applications such as driver eye tracking or collision avoidance. This paper addresses the synchronisation problem which arises when multivision camera systems are used to capture the high speed motion common in such applications. Methods: An experimental, high-speed tri-vision camera system intended for real-time driver eye-blink and saccade measurement was designed, developed, implemented and tested using prototype, ultra-high dynamic range, automotive-grade image sensors specifically developed by E2V (formerly Atmel) Grenoble SA as part of the European FP6 project – sensation (advanced sensor development for attention stress, vigilance and sleep/wakefulness monitoring). Results : The developed system can sustain frame rates of 59.8 Hz at the full stereovision resolution of 1280 × 480 but this can reach 750 Hz when a 10 k pixel Region of Interest (ROI) is used, with a maximum global shutter speed of 1/48000 s and a shutter efficiency of 99.7%. The data can be reliably transmitted uncompressed over standard copper Camera-Link® cables over 5 metres. The synchronisation error between the left and right stereo images is less than 100 ps and this has been verified both electrically and optically. Synchronisation is automatically established at boot-up and maintained during resolution changes. A third camera in the set can be configured independently. The dynamic range of the 10bit sensors exceeds 123 dB with a spectral sensitivity extending well into the infra-red range. Conclusion: The system was subjected to a comprehensive testing protocol, which confirms that the salient requirements for the driver monitoring application are adequately met and in some respects, exceeded. The synchronisation technique presented may also benefit several other automotive stereovision applications including near and far-field obstacle detection and collision avoidance, road condition monitoring and others.Partially funded by the EU FP6 through the IST-507231 SENSATION project.peer-reviewe

DP-fill: a dynamic programming approach to X-filling for minimizing peak test power in scan tests

At-speed testing is crucial to catch small delay defects that occur during the manufacture of high performance digital chips. Launch-Off-Capture (LOC) and Launch-Off-Shift (LOS) are two prevalently used schemes for this purpose. LOS scheme achieves higher fault coverage while consuming lesser test time over LOC scheme, but dissipates higher power during the capture phase of the at-speed test. Excessive IR-drop during capture phase on the power grid causes false delay failures leading to significant yield reduction that is unwarranted. As reported in literature, an intelligent filling of don't care bits (X-filling) in test cubes has yielded significant power reduction. Given that the tests output by automatic test pattern generation (ATPG) tools for big circuits have large number of don't care bits, the X-filling technique is very effective for them. Assuming that the design for testability (DFT) scheme preserves the state of the combinational logic between capture phases of successive patterns, this paper maps the problem of optimal X-filling for peak power minimization during LOS scheme to a variant of interval coloring problem and proposes a dynamic programming (DP) algorithm for the same along with a theoretical proof for its optimality. To the best of our knowledge, this is the first ever reported X-filling algorithm that is optimal. The proposed algorithm when experimented on ITC99 benchmarks produced peak power savings of up to 34% over the best known low power X-filling algorithm for LOS testing. Interestingly, it is observed that the power savings increase with the size of the circuit

Algorithms for Power Aware Testing of Nanometer Digital ICs

At-speed testing of deep-submicron digital very large scale integrated (VLSI) circuits has become mandatory to catch small delay defects. Now, due to continuous shrinking of complementary metal oxide semiconductor (CMOS) transistor feature size, power density grows geometrically with technology scaling. Additionally, power dissipation inside a digital circuit during the testing phase (for test vectors under all fault models (Potluri, 2015)) is several times higher than its power dissipation during the normal functional phase of operation. Due to this, the currents that flow in the power grid during the testing phase, are much higher than what the power grid is designed for (the functional phase of operation). As a result, during at-speed testing, the supply grid experiences unacceptable supply IR-drop, ultimately leading to delay failures during at-speed testing. Since these failures are specific to testing and do not occur during functional phase of operation of the chip, these failures are usually referred to false failures, and they reduce the yield of the chip, which is undesirable. In nanometer regime, process parameter variations has become a major problem. Due to the variation in signalling delays caused by these variations, it is important to perform at-speed testing even for stuck faults, to reduce the test escapes (McCluskey and Tseng, 2000; Vorisek et al., 2004). In this context, the problem of excessive peak power dissipation causing false failures, that was addressed previously in the context of at-speed transition fault testing (Saxena et al., 2003; Devanathan et al., 2007a,b,c), also becomes prominent in the context of at-speed testing of stuck faults (Maxwell et al., 1996; McCluskey and Tseng, 2000; Vorisek et al., 2004; Prabhu and Abraham, 2012; Potluri, 2015; Potluri et al., 2015). It is well known that excessive supply IR-drop during at-speed testing can be kept under control by minimizing switching activity during testing (Saxena et al., 2003). There is a rich collection of techniques proposed in the past for reduction of peak switching activity during at-speed testing of transition/delay faults ii in both combinational and sequential circuits. As far as at-speed testing of stuck faults are concerned, while there were some techniques proposed in the past for combinational circuits (Girard et al., 1998; Dabholkar et al., 1998), there are no techniques concerning the same for sequential circuits. This thesis addresses this open problem. We propose algorithms for minimization of peak switching activity during at-speed testing of stuck faults in sequential digital circuits under the combinational state preservation scan (CSP-scan) architecture (Potluri, 2015; Potluri et al., 2015). First, we show that, under this CSP-scan architecture, when the test set is completely specified, the peak switching activity during testing can be minimized by solving the Bottleneck Traveling Salesman Problem (BTSP). This mapping of peak test switching activity minimization problem to BTSP is novel, and proposed for the first time in the literature. Usually, as circuit size increases, the percentage of don’t cares in the test set increases. As a result, test vector ordering for any arbitrary filling of don’t care bits is insufficient for producing effective reduction in switching activity during testing of large circuits. Since don’t cares dominate the test sets for larger circuits, don’t care filling plays a crucial role in reducing switching activity during testing. Taking this into consideration, we propose an algorithm, XStat, which is capable of performing test vector ordering while preserving don’t care bits in the test vectors, following which, the don’t cares are filled in an intelligent fashion for minimizing input switching activity, which effectively minimizes switching activity inside the circuit (Girard et al., 1998). Through empirical validation on benchmark circuits, we show that XStat minimizes peak switching activity significantly, during testing. Although XStat is a very powerful heuristic for minimizing peak input-switchingactivity, it will not guarantee optimality. To address this issue, we propose an algorithm that uses Dynamic Programming to calculate the lower bound for a given sequence of test vectors, and subsequently uses a greedy strategy for filling don’t cares in this sequence to achieve this lower bound, thereby guaranteeing optimality. This algorithm, which we refer to as DP-fill in this thesis, provides the globally optimal solution for minimizing peak input-switching-activity and also is the best known in the literature for minimizing peak input-switching-activity during testing. The proof of optimality of DP-fill in minimizing peak input-switching-activity is also provided in this thesis

Proceedings of the NSSDC Conference on Mass Storage Systems and Technologies for Space and Earth Science Applications

The proceedings of the National Space Science Data Center Conference on Mass Storage Systems and Technologies for Space and Earth Science Applications held July 23 through 25, 1991 at the NASA/Goddard Space Flight Center are presented. The program includes a keynote address, invited technical papers, and selected technical presentations to provide a broad forum for the discussion of a number of important issues in the field of mass storage systems. Topics include magnetic disk and tape technologies, optical disk and tape, software storage and file management systems, and experiences with the use of a large, distributed storage system. The technical presentations describe integrated mass storage systems that are expected to be available commercially. Also included is a series of presentations from Federal Government organizations and research institutions covering their mass storage requirements for the 1990's

VETA-I x ray test analysis

This interim report presents some definitive results from our analysis of the VETA-I x-ray testing data. It also provides a description of the hardware and software used in the conduct of the VETA-I x-ray test program performed at the MSFC x-ray Calibration Facility (XRCF). These test results also serve to supply data and information to include in the TRW final report required by DPD 692, DR XC04. To provide an authoritative compendium of results, we have taken nine papers as published in the SPIE Symposium, 'Grazing Incidence X-ray/EUV Optics for Astronomy and Projection Lithography' and have reproduced them as the content of this report

Image Processing Using FPGAs

This book presents a selection of papers representing current research on using field programmable gate arrays (FPGAs) for realising image processing algorithms. These papers are reprints of papers selected for a Special Issue of the Journal of Imaging on image processing using FPGAs. A diverse range of topics is covered, including parallel soft processors, memory management, image filters, segmentation, clustering, image analysis, and image compression. Applications include traffic sign recognition for autonomous driving, cell detection for histopathology, and video compression. Collectively, they represent the current state-of-the-art on image processing using FPGAs