Low Power Filtering Techniques for Wideband and Wireless Applications

This dissertation presents design and implementation of continuous time analog filters for two specific applications: wideband analog systems such as disk drive channel and low-power wireless applications. Specific focus has been techniques that reduce the power requirements of the overall system either through improvement in architecture or efficiency of the analog building blocks. The first problem that this dissertation addresses is the implementation of wideband filters with high equalization gain. An efficient architecture that realizes equalization zeros by combining available transfer functions associated with a biquadratic cell is proposed. A 330MHz, 5th order Gm-C lowpass Butterworth filter with 24dB boost is designed using the proposed architecture. The prototype fabricated in standard 0.35um CMOS process shows -41dB of IM3 for 250mV peak to peak swing with 8.6mW/pole of power dissipation. Also, an LC prototype implemented using similar architecture is discussed in brief. It is shown that, for practical range of frequency and SNR, LC based design is more power efficient than a Gm-C one, though at the cost of much larger area. Secondly, a complementary current mirror based building block is proposed, which pushes the limits imposed by conventional transconductors on the powerefficiency of Gm-C filters. Signal processing through complementary devices provides good linearity and Gm/Id efficiency and is shown to improve power efficiency by nearly 7 times. A current-mode 4th order Butterworth filter is designed, in 0.13um UMC technology, using the proposed building. It provides 54.2dB IM3 and 55dB SNR in 1.3GHz bandwidth while consuming as low as 24mW of power. All CMOS filter realization occupies a relatively small area and is well suited for integration in deep submicron technologies. Thirdly, a 20MHz, 68dB dynamic range active RC filter is presented. This filter is designed for a ten bit continuous time sigma delta ADC architecture developed specifically for fine-line CMOS technologies. Inverter based amplification and a common mode feedback for such amplifiers are discussed. The filter consumes 5mW of power and occupies an area of 0.07 mm2

Analog/RF Circuit Design Techniques for Nanometerscale IC Technologies

CMOS evolution introduces several problems in analog design. Gate-leakage mismatch exceeds conventional matching tolerances requiring active cancellation techniques or alternative architectures. One strategy to deal with the use of lower supply voltages is to operate critical parts at higher supply voltages, by exploiting combinations of thin- and thick-oxide transistors. Alternatively, low voltage circuit techniques are successfully developed. In order to benefit from nanometer scale CMOS technology, more functionality is shifted to the digital domain, including parts of the RF circuits. At the same time, analog control for digital and digital control for analog emerges to deal with current and upcoming imperfections

A robust 2.4 GHz time-of-arrival based ranging system with sub-meter accuracy: feasibility study and realization of low power CMOS receiver

Draadloze sensornetwerken worden meer en meer aangewend om verschillende soorten informatie te verzamelen. De locatie, waar deze informatie verzameld is, is een belangerijke eigenschap en voor sommige toepassingen, zoals het volgen van personen of goederen, zelfs de meest belangrijke en mogelijkmakende factor. Om de positie van een sensor te bepalen, is een technologie nodig die de afstand tot een gekend referentiepunt schat. Door verschillende afstandsmetingen te combineren, is het mogelijk de absolute locatie van de node te berekenen

Design of a correlator for UWB transceivers

Master'sMASTER OF ENGINEERIN

Polyphase filter with parametric tuning

Tese de mestrado integrado. Engenharia Electrotécnica e de Computadores. Faculdade de Engenharia. Universidade do Porto. 201

Digitally-Assisted RF IC Design Techniques for Reliable Performance

Semiconductor industries have competitively scaled down CMOS devices to attain benefits of low cost, high performance, and high integration density in digital integrated circuits. On the other hand, deep scaled technologies inextricably accompany a large process variation, supply voltage scaling, and reduction in breakdown voltages of transistors. When it comes to RF/analog IC design, CMOS scaling adversely affects its reliability due to large performance variation and limited linearity. For addressing the issues related to variations and linearity, this research proposes the following digitally-assisted RF circuit design techniques: self-calibration system for RF phase shifters and wide dynamic range LNAs. Due to PVT variations in scaled technologies, RF phase shifter design becomes more challenging with device scaling. In the proposed self-calibration topology, we devised a novel phase sensing method and a pulsewidth-to-digital converter. The feedback controller is also designed in digital domain, which is robust to PVT variations. These unique techniques enable a sensing/control loop tolerant to PVT variations. The self-calibration loop was applied to a 7 to 13GHz phase shifter. With the calibration, the estimated phase error is less than 2 degrees. To overcome the linearity issue in scaled technologies, a digitally-controlled dual-mode LNA design is presented. A narrowband (5.1GHz) and a wideband (0.8 to 6GHz) LNA can be toggled between high-gain and high-linearity modes by digital control bits according to the input signal power. A compact design, which provides negligible performance degradation by additional circuitry, is achieved by sharing most of the components between the two operation modes. The narrowband and the wideband LNA achieves an input-referred P1dB of -1.8dBm and +4.2dBm, respectively

RF Amplification and Filtering Techniques for Cellular Receivers

The usage of various wireless standards, such as Bluetooth, Wi-Fi, GPS, and 4G/5G cellular, has been continually increasing. In order to utilize the frequency bands efficiently and to support new communication standards with lower power consumption, lower occupied volume and at reduced costs, multimode transceivers, software defined radios (SDRs), cognitive radios, etc., have been actively investigated. Broadband behavior of a wireless receiver is typically defined by its front-end low-noise amplifier (LNA), whose design must consider trade-offs between input matching, noise figure (NF), gain, bandwidth, linearity, and voltage headroom in a given process technology. Moreover, monolithic RF wireless receivers have been trending toward high intermediatefrequency (IF) or superhetrodyne radios thanks to recent breakthroughs in silicon integration of band-pass channel-select filters. The main motivation is to avoid the common issues in the currently predominant zero/low-IF receivers, such as poor 2nd-order nonlinearity, sensitivity to 1/f (i.e. flicker) noise and time-variant dc offsets, especially in the fine CMOS technology. To avoid interferers and blockers at the susceptible image frequencies that the high-IF entails, band-pass filters (BPF) with high quality (Q) factor components for sharp transfer-function transition characteristics are now required. In addition, integrated low-pass filters (LPF) with strong rejection of out-of-band frequency components are essential building blocks in a variety of applications, such as telecommunications, video signal processing, anti-aliasing filtering, etc. Attention is drawn toward structures featuring low noise, small area, high in-/out-of-band linearity performance, and low-power consumption. This thesis comprises three main parts. In the first part (Chapters 2 and 3), we focus on the design and implementation of several innovative wideband low-noise (transconductance) amplifiers [LN(T)A] for wireless cellular applications. In the first design, we introduce new approaches to reduce the noise figure of the noise-cancellation LNAs without sacrificing the power consumption budget, which leads to NF of 2 dB without adding extra power consumption. The proposed LNAs also have the capability to be used in current-mode receivers, especially in discrete-time receivers, as in the form of low noise transconductance amplifier (LNTA). In the second design, two different two-fold noise cancellation approaches are proposed, which not only improve the noise performance of the design, but also achieve high linearity (IIP3=+4.25 dBm). The proposed LN(T)As are implemented in TSMC 28-nm LP CMOS technology to prove that they are suitable for applications such as sub-6 GHz 5G receivers. The second objective of this dissertation research is to invent a novel method of band-pass filtering, which leads to achieving very sharp and selective band-pass filtering with high linearity and low input referred (IRN) noise (Chapter 4). This technique improves the noise and linearity performance without adding extra clock phases. Hence, the duty cycle of the clock phases stays constant, despite the sophisticated improvements. Moreover, due to its sharp filtering, it can filter out high blockers of near channels and can increase the receiver’s blocker tolerance. With the same total capacitor size and clock duty cycle as in a 1st-order complex charge-sharing band-pass filter (CS BPF), the proposed design achieves 20 dB better out-of-band filtering compared to the prior-art 1st-order CS BPF and 10 dB better out-of-band filtering compared to the conventional 2nd-order C-CS BPF. Finally, the stop-band rejection of the discrete-time infinite-impulse response (IIR) lowpass filter is improved by applying a novel technique to enhance the anti-aliasing filtering (Chapter 5). The aim is to introduce a 4th-order charge rotating (CR) discrete-time (DT) LPF, which achieves the record of stop-band rejection of 120 dB by using a novel pseudolinear interpolation technique while keeping the sampling frequency and the capacitor values constant

Bandpass electromechanical sigma-delta modulator

Ph.DDOCTOR OF PHILOSOPH