DC-DC power converter research for Orbiter/Station power exchange

This project was to produce innovative DC-DC power converter concepts which are appropriate for the power exchange between the Orbiter and the Space Station Freedom (SSF). The new converters must interface three regulated power buses on SSF, which are at different voltages, with three fuel cell power buses on the Orbiter which can be at different voltages and should be tracked independently. Power exchange is to be bi-directional between the SSF and the Orbiter. The new converters must satisfy the above operational requirements with better weight, volume, efficiency, and reliability than is available from the present conventional technology. Two families of zero current DC-DC converters were developed and successfully adapted to this application. Most of the converters developed are new and are presented

A New ZCS-PWM Full-Bridge Boost Converter

The objective of this thesis is to propose, analyze, design, implement, and experimentally confirm the operation of a new Zero-Current-Switching PWM dc-dc full- bridge boost converter that does not have the drawbacks ofpreviously proposed circuits of the same type. In this thesis, the general operating principles of the converter are reviewed, and the converter’s operation is discussed in detail and analyzed mathematically. As a result of the mathematical analysis, key voltage and current equations that describes the operation of the auxiliary circuit and other converter devices have been derived. The steady state equations of each mode of operation are used as the basis of a MATLAB program that is used to generate steady-state characteristic curves that shows the effect that individual circuit parameters have on the operation of the auxiliary circuit and the boost converter. Observations as to their steady-state characteristics are made and the curves are used as part of a design procedure to select the components of the converter, especially those of the auxiliary circuit. An experimental full-bridge PWM dc-dc boost converter prototype is built based on the converter design and typical waveforms are presented. The efficiency of the proposed converter operating with the auxiliary circuit is compared to that of a standard PWM dc-dc full-bridge boost converter and the increased efficiency o f the proposed converter is confirme

Zero-voltage-switching buck converter with low-voltage stress using coupled inductor

This study presents a new zero-voltage-switching (ZVS) buck converter. The proposed converter utilises a coupled inductor to implement the output filter inductor as well as the auxiliary inductor which is commonly employed to realise ZVS for switches. Additional magnetic core for the auxiliary inductor in traditional ZVS converters is eliminated and hence reduced cost is achieved. Moreover, thanks to the series connection between the input and output, the switch voltage stress in the steady state is reduced and thus the ZVS operation can be easier achieved. Then the leakage inductor current circulating in the auxiliary switch is decreased, contributing to reduced conduction losses. In particular, low-voltage rating devices with low on-state resistance can be adopted to further improve efficiency in applications with non-zero output voltage all the time, such as the battery charger. Furthermore, the reverse-recovery problem of the diode is significantly alleviated by the leakage inductor of coupled inductor. In the study, operation principle and steady-state analysis of the proposed converter are presented in detail. Meanwhile, design considerations are given to obtain circuit parameters. Finally, simulations and experiments on a 200 W prototype circuit validate the advantages and effectiveness of the proposed converter

Analysis of a new family of DC-DC converters with input-parallel output-series structure

There is an increasing trend of development and installation of switching power supplies due to their highly efficient power conversion, fast power control and high quality power conditioning for applications such as renewable energy integration and energy storage management systems. In most of these applications, high voltage conversion ratio is required. However, basic switching converters have limited voltage conversion ratio. There has been much research into development of high gain power converters. While most of the reported topologies focus on high gain and high efficiency, in this thesis, the input and output ripple currents and reliability are also considered to derive a new converter structure suitable for high step-up voltage conversion applications. High ripple currents and voltages at the input and output of dc-dc converters are not desirable because they may affect the operation of the dc source or the load. A number of converters operating in an interleaved manner can reduce these ripples. This thesis proposes a dc/dc switching converter structure which is capable of reducing the ripple problem through interleaved action, in addition to high gain and high efficiency voltage conversion. The thesis analyses the proposed converter structure through a dual buck-boost converter topology. The structure allows different converter topologies and combinations of them for different applications to be configured. The study begins with a motivation and a literature review of dc/dc converters. The new family of high step-up converters is introduced with an interleaved buck-boost as an example, followed by small-signal analysis. Experimental verifications, conclusions and future work are discussed

Assessment of novel power electronic converters for drives applications

Phd ThesisIn the last twenty years, industrial and academic research has produced over one hundred new converter topologies for drives applications. Regrettably, most of the published work has been directed towards a single topology, giving an overall impression of a large number of unconnected, competing techniques. To provide insight into this wide ranging subject area, an overview of converter topologies is presented. Each topology is classified according to its mode of operation and a family tree is derived encompassing all converter types. Selected converters in each class are analysed, simulated and key operational characteristics identified. Issues associated with the practical implementation of analysed topologies are discussed in detail. Of all AC-AC conversion techniques, it is concluded that softswitching converter topologies offer the most attractive alternative to the standard hard switched converter in the power range up to 100kW because of their high performance to cost ratio. Of the softswitching converters, resonant dc-link topologies are shown to produce the poorest output performance although they offer the cheapest solution. Auxiliary pole commutated inverters, on the other hand, can achieve levels of performance approaching those of the hard switched topology while retaining the benefits of softswitching. It is concluded that the auxiliary commutated resonant pole inverter (ACPI) topology offers the greatest potential for exploitation in spite of its relatively high capital cost. Experimental results are presented for a 20kW hard switched inverter and an equivalent 20kW ACPI. In each case the converter controller is implanted using a digital signal processor. For the ACPI, a new control scheme, which eliminates the need for switch current and voltage sensors, is implemented. Results show that the ACPI produces lower overall losses when compared to its hardswitching counterpart. In addition, device voltage stress, output dv/dt and levels of high frequency output harmonics are all reduced. Finally, it is concluded that modularisation of the active devices, optimisation of semiconductor design and a reduction in the number of additional sensors through the use of novel control methods, such as those presented, will all play a part in the realisation of an economically viable system.Research Committee of the University of Newcastle upon Tyn

Analysis and Design of a Soft Switching Z-Source Boost DC-DC Converter

This paper proposes a high step-up fully soft switched Z-source Boost DC-DC converter, which uses two resonant paths to create soft switching conditions for switches and diodes and also increases the voltage gain. The proposed converter only has one switch, so it has a simple structure. Furthermore, its control circuit remains pulse width modulation. Since soft switching conditions are provided for all switching elements, the converter efficiency is very high. This converter also has all advantages of Z-source converters. The converter is analyzed and simulated in PSPICE software. The results confirm the aforementioned advantages and features of the proposed converte