ON FPGA BASED ACCELERATION OF IMAGE PROCESSING IN MOBILE ROBOTICS

In visual navigation tasks, a lack of the computational resources is one of the main limitations of micro robotic platforms to be deployed in autonomous missions. It is because the most of nowadays techniques of visual navigation relies on a detection of salient points that is computationally very demanding. In this paper, an FPGA assisted acceleration of image processing is considered to overcome limitations of computational resources available on-board and to enable high processing speeds while it may lower the power consumption of the system. The paper reports on performance evaluation of the CPU–based and FPGA–based implementations of a visual teach-and-repeat navigation system based on detection and tracking of the FAST image salient points. The results indicate that even a computationally efficient FAST algorithm can benefit from a parallel (low–cost) FPGA–based implementation that has a competitive processing time but more importantly it is a more power efficient

High-performance hardware accelerators for image processing in space applications

Mars is a hard place to reach. While there have been many notable success stories in getting probes to the Red Planet, the historical record is full of bad news. The success rate for actually landing on the Martian surface is even worse, roughly 30%. This low success rate must be mainly credited to the Mars environment characteristics. In the Mars atmosphere strong winds frequently breath. This phenomena usually modifies the lander descending trajectory diverging it from the target one. Moreover, the Mars surface is not the best place where performing a safe land. It is pitched by many and close craters and huge stones, and characterized by huge mountains and hills (e.g., Olympus Mons is 648 km in diameter and 27 km tall). For these reasons a mission failure due to a landing in huge craters, on big stones or on part of the surface characterized by a high slope is highly probable. In the last years, all space agencies have increased their research efforts in order to enhance the success rate of Mars missions. In particular, the two hottest research topics are: the active debris removal and the guided landing on Mars. The former aims at finding new methods to remove space debris exploiting unmanned spacecrafts. These must be able to autonomously: detect a debris, analyses it, in order to extract its characteristics in terms of weight, speed and dimension, and, eventually, rendezvous with it. In order to perform these tasks, the spacecraft must have high vision capabilities. In other words, it must be able to take pictures and process them with very complex image processing algorithms in order to detect, track and analyse the debris. The latter aims at increasing the landing point precision (i.e., landing ellipse) on Mars. Future space-missions will increasingly adopt Video Based Navigation systems to assist the entry, descent and landing (EDL) phase of space modules (e.g., spacecrafts), enhancing the precision of automatic EDL navigation systems. For instance, recent space exploration missions, e.g., Spirity, Oppurtunity, and Curiosity, made use of an EDL procedure aiming at following a fixed and precomputed descending trajectory to reach a precise landing point. This approach guarantees a maximum landing point precision of 20 km. By comparing this data with the Mars environment characteristics, it is possible to understand how the mission failure probability still remains really high. A very challenging problem is to design an autonomous-guided EDL system able to even more reduce the landing ellipse, guaranteeing to avoid the landing in dangerous area of Mars surface (e.g., huge craters or big stones) that could lead to the mission failure. The autonomous behaviour of the system is mandatory since a manual driven approach is not feasible due to the distance between Earth and Mars. Since this distance varies from 56 to 100 million of km approximately due to the orbit eccentricity, even if a signal transmission at the light speed could be possible, in the best case the transmission time would be around 31 minutes, exceeding so the overall duration of the EDL phase. In both applications, algorithms must guarantee self-adaptability to the environmental conditions. Since the Mars (and in general the space) harsh conditions are difficult to be predicted at design time, these algorithms must be able to automatically tune the internal parameters depending on the current conditions. Moreover, real-time performances are another key factor. Since a software implementation of these computational intensive tasks cannot reach the required performances, these algorithms must be accelerated via hardware. For this reasons, this thesis presents my research work done on advanced image processing algorithms for space applications and the associated hardware accelerators. My research activity has been focused on both the algorithm and their hardware implementations. Concerning the first aspect, I mainly focused my research effort to integrate self-adaptability features in the existing algorithms. While concerning the second, I studied and validated a methodology to efficiently develop, verify and validate hardware components aimed at accelerating video-based applications. This approach allowed me to develop and test high performance hardware accelerators that strongly overcome the performances of the actual state-of-the-art implementations. The thesis is organized in four main chapters. Chapter 2 starts with a brief introduction about the story of digital image processing. The main content of this chapter is the description of space missions in which digital image processing has a key role. A major effort has been spent on the missions in which my research activity has a substantial impact. In particular, for these missions, this chapter deeply analizes and evaluates the state-of-the-art approaches and algorithms. Chapter 3 analyzes and compares the two technologies used to implement high performances hardware accelerators, i.e., Application Specific Integrated Circuits (ASICs) and Field Programmable Gate Arrays (FPGAs). Thanks to this information the reader may understand the main reasons behind the decision of space agencies to exploit FPGAs instead of ASICs for high-performance hardware accelerators in space missions, even if FPGAs are more sensible to Single Event Upsets (i.e., transient error induced on hardware component by alpha particles and solar radiation in space). Moreover, this chapter deeply describes the three available space-grade FPGA technologies (i.e., One-time Programmable, Flash-based, and SRAM-based), and the main fault-mitigation techniques against SEUs that are mandatory for employing space-grade FPGAs in actual missions. Chapter 4 describes one of the main contribution of my research work: a library of high-performance hardware accelerators for image processing in space applications. The basic idea behind this library is to offer to designers a set of validated hardware components able to strongly speed up the basic image processing operations commonly used in an image processing chain. In other words, these components can be directly used as elementary building blocks to easily create a complex image processing system, without wasting time in the debug and validation phase. This library groups the proposed hardware accelerators in IP-core families. The components contained in a same family share the same provided functionality and input/output interface. This harmonization in the I/O interface enables to substitute, inside a complex image processing system, components of the same family without requiring modifications to the system communication infrastructure. In addition to the analysis of the internal architecture of the proposed components, another important aspect of this chapter is the methodology used to develop, verify and validate the proposed high performance image processing hardware accelerators. This methodology involves the usage of different programming and hardware description languages in order to support the designer from the algorithm modelling up to the hardware implementation and validation. Chapter 5 presents the proposed complex image processing systems. In particular, it exploits a set of actual case studies, associated with the most recent space agency needs, to show how the hardware accelerator components can be assembled to build a complex image processing system. In addition to the hardware accelerators contained in the library, the described complex system embeds innovative ad-hoc hardware components and software routines able to provide high performance and self-adaptable image processing functionalities. To prove the benefits of the proposed methodology, each case study is concluded with a comparison with the current state-of-the-art implementations, highlighting the benefits in terms of performances and self-adaptability to the environmental conditions

FPGA Accelerated Discrete-SURF for Real-Time Homography Estimation

This paper describes our hardware accelerated, FPGA implementation of SURF, named Discrete SURF, to support real-time homography estimation for close range aerial navigation. The SURF algorithm provides feature matches between a model and a scene which can be used to find the transformation between the camera and the model. Previous implementations of SURF have partially employed FPGAs to accelerate the feature detection stage of upright only image comparisons. We extend the work of previous implementations by providing an FPGA implementation that allows rotation during image comparisons in order to facilitate aerial navigation. We also expand beyond feature detection as the complete Discrete SURF algorithm is run on the FPGA, rather than piped into processors. This not only minimizes overhead and increases the parallelization of the algorithm, but also allows the algorithm to be easily ported to different FPGAs. Furthermore, the Discrete SURF module is a logic-only implementation that does not rely on external hardware which therefore decreases the overall size, weight and power of the device while also allowing for easy FPGA to ASIC conversion. We evaluate the Discrete SURF algorithm in terms of performance against the original SURF and upright SURF algorithms implemented in OpenCV. Finally, we show how Discrete SURF is more compatible with an aerial navigation scenario than previous works, since rotation invariance must be considered in addition to scale

Software Porting of a 3D Reconstruction Algorithm to Razorcam Embedded System on Chip

A method is presented to calculate depth information for a UAV navigation system from Keypoints in two consecutive image frames using a monocular camera sensor as input and the OpenCV library. This method was first implemented in software and run on a general-purpose Intel CPU, then ported to the RazorCam Embedded Smart-Camera System and run on an ARM CPU onboard the Xilinx Zynq-7000. The results of performance and accuracy testing of the software implementation are then shown and analyzed, demonstrating a successful port of the software to the RazorCam embedded system on chip that could potentially be used onboard a UAV with tight constraints of size, weight, and power. The potential impacts will be seen through the continuation of this research in the Smart ES lab at University of Arkansas

A low-power hardware accelerator for ORB feature extraction in self-driving cars

Simultaneous Localization And Mapping (SLAM) is a key component for autonomous navigation. SLAM consists of building and creating a map of an unknown environment while keeping track of the exploring agent's location within it. An effective implementation of SLAM presents important challenges due to real-time inherent constraints and energy consumption. ORB-SLAM is a state-of-the-art Visual SLAM system based on cameras that can be used for self-driving cars. In this paper, we propose a high-performance, energy-efficient and functionally accurate hardware accelerator for ORB-SLAM, focusing on its most time-consuming stage: Oriented FAST and Rotated BRIEF (ORB) feature extraction. We identify the BRIEF descriptor generation as the main bottleneck, as it exhibits highly irregular access patterns to local on-chip memories, causing a high performance penalty due to bank conflicts. We propose a genetic algorithm to generate an optimal memory access pattern offline, which greatly simplifies the hardware while minimizing bank conflicts in the computation of the BRIEF descriptor. Compared with a CPU system, the accelerator achieves 8x speedup and 1957x reduction in power dissipation.This work has been supported by the CoCoUnit ERC Advanced Grant of the EU’s Horizon 2020 program (grant No 833057), the Spanish State Research Agency (MCIN/AEI) under grant PID2020-113172RB-I00, the ICREA Academia program and the FPU grant FPU18/04413.Peer ReviewedPostprint (author's final draft

Enhancing Real-time Embedded Image Processing Robustness on Reconfigurable Devices for Critical Applications

Nowadays, image processing is increasingly used in several application fields, such as biomedical, aerospace, or automotive. Within these fields, image processing is used to serve both non-critical and critical tasks. As example, in automotive, cameras are becoming key sensors in increasing car safety, driving assistance and driving comfort. They have been employed for infotainment (non-critical), as well as for some driver assistance tasks (critical), such as Forward Collision Avoidance, Intelligent Speed Control, or Pedestrian Detection. The complexity of these algorithms brings a challenge in real-time image processing systems, requiring high computing capacity, usually not available in processors for embedded systems. Hardware acceleration is therefore crucial, and devices such as Field Programmable Gate Arrays (FPGAs) best fit the growing demand of computational capabilities. These devices can assist embedded processors by significantly speeding-up computationally intensive software algorithms. Moreover, critical applications introduce strict requirements not only from the real-time constraints, but also from the device reliability and algorithm robustness points of view. Technology scaling is highlighting reliability problems related to aging phenomena, and to the increasing sensitivity of digital devices to external radiation events that can cause transient or even permanent faults. These faults can lead to wrong information processed or, in the worst case, to a dangerous system failure. In this context, the reconfigurable nature of FPGA devices can be exploited to increase the system reliability and robustness by leveraging Dynamic Partial Reconfiguration features. The research work presented in this thesis focuses on the development of techniques for implementing efficient and robust real-time embedded image processing hardware accelerators and systems for mission-critical applications. Three main challenges have been faced and will be discussed, along with proposed solutions, throughout the thesis: (i) achieving real-time performances, (ii) enhancing algorithm robustness, and (iii) increasing overall system's dependability. In order to ensure real-time performances, efficient FPGA-based hardware accelerators implementing selected image processing algorithms have been developed. Functionalities offered by the target technology, and algorithm's characteristics have been constantly taken into account while designing such accelerators, in order to efficiently tailor algorithm's operations to available hardware resources. On the other hand, the key idea for increasing image processing algorithms' robustness is to introduce self-adaptivity features at algorithm level, in order to maintain constant, or improve, the quality of results for a wide range of input conditions, that are not always fully predictable at design-time (e.g., noise level variations). This has been accomplished by measuring at run-time some characteristics of the input images, and then tuning the algorithm parameters based on such estimations. Dynamic reconfiguration features of modern reconfigurable FPGA have been extensively exploited in order to integrate run-time adaptivity into the designed hardware accelerators. Tools and methodologies have been also developed in order to increase the overall system dependability during reconfiguration processes, thus providing safe run-time adaptation mechanisms. In addition, taking into account the target technology and the environments in which the developed hardware accelerators and systems may be employed, dependability issues have been analyzed, leading to the development of a platform for quickly assessing the reliability and characterizing the behavior of hardware accelerators implemented on reconfigurable FPGAs when they are affected by such faults

Design and Development of an FPGA-based Hardware Accelerator for Corner Feature Extraction and Genetic Algorithm-based SLAM System

Simultaneous Localization and Mapping (SLAM) systems are crucial parts of mobile robots. These systems require a large number of computing units, have significant real-time requirements and are also a vital factor which can determine the stability, operability and power consumption of robots. This thesis aims to improve the calculation speed of a lidar-based SLAM system in domestic scenes, reduce the power consumption of the SLAM algorithm, and reduce the overall cost of the whole platform. Lightweight, low-power and parallel optimization of SLAM algorithms are researched. In the thesis, two SLAM systems are designed and developed with a focus on energy-efficient and fast hardware-level design: a geometric method based on corner extraction and a genetic algorithm-based approach. Finally, an FPGA-based hardware accelerated SLAM is implemented and realized, and compared to a software-based system. As for the front-end SLAM system, a method of using a Corner Feature Extraction (CFE) algorithm on FPGA platforms is first proposed to improve the speed of the feature extraction. Considering building a back-end SLAM system with low power consumption, a SLAM system based on genetic algorithm combined with algorithms such as Extended Kalman Filter (EKF) and FastSLAM to reduce the amount of calculation in the SLAM system is also proposed. Finally, the thesis also proposes and implements an adaptive feature map which can replace a grid point map to reduce the amount of calculation and utilization of hardware resources. In this thesis, the lidar SLAM system with front-end and back-end parts mentioned above is implemented on the Xilinx PYNQ Z2 Platform. The implementation is operated on a mobile robot prototype and evaluated in real scenes. Compared with the implementation on the Raspberry Pi 3B+, the implementation in this thesis can save 86.25% of power consumption. The lidar SLAM system only takes 20 ms for location calculation in each scan which is 5.31 times faster compared with the software implementation with EKF

Using Prior Knowledge for Verification and Elimination of Stationary and Variable Objects in Real-time Images

With the evolving technologies in the autonomous vehicle industry, now it has become possible for automobile passengers to sit relaxed instead of driving the car. Technologies like object detection, object identification, and image segmentation have enabled an autonomous car to identify and detect an object on the road in order to drive safely. While an autonomous car drives by itself on the road, the types of objects surrounding the car can be dynamic (e.g., cars and pedestrians), stationary (e.g., buildings and benches), and variable (e.g., trees) depending on if the location or shape of an object changes or not. Different from the existing image-based approaches to detect and recognize objects in the scene, in this research 3D virtual world is employed to verify and eliminate stationary and variable objects to allow the autonomous car to focus on dynamic objects that may cause danger to its driving. This methodology takes advantage of prior knowledge of stationary and variable objects presented in a virtual city and verifies their existence in a real-time scene by matching keypoints between the virtual and real objects. In case of a stationary or variable object that does not exist in the virtual world due to incomplete pre-existing information, this method uses machine learning for object detection. Verified objects are then removed from the real-time image with a combined algorithm using contour detection and class activation map (CAM), which helps to enhance the efficiency and accuracy when recognizing moving objects

A Survey on FPGA-Based Sensor Systems: Towards Intelligent and Reconfigurable Low-Power Sensors for Computer Vision, Control and Signal Processing

The current trend in the evolution of sensor systems seeks ways to provide more accuracy and resolution, while at the same time decreasing the size and power consumption. The use of Field Programmable Gate Arrays (FPGAs) provides specific reprogrammable hardware technology that can be properly exploited to obtain a reconfigurable sensor system. This adaptation capability enables the implementation of complex applications using the partial reconfigurability at a very low-power consumption. For highly demanding tasks FPGAs have been favored due to the high efficiency provided by their architectural flexibility (parallelism, on-chip memory, etc.), reconfigurability and superb performance in the development of algorithms. FPGAs have improved the performance of sensor systems and have triggered a clear increase in their use in new fields of application. A new generation of smarter, reconfigurable and lower power consumption sensors is being developed in Spain based on FPGAs. In this paper, a review of these developments is presented, describing as well the FPGA technologies employed by the different research groups and providing an overview of future research within this field.The research leading to these results has received funding from the Spanish Government and European FEDER funds (DPI2012-32390), the Valencia Regional Government (PROMETEO/2013/085) and the University of Alicante (GRE12-17)