Supercapacitor assisted low dropout regulators (SCALDO) with reduced switches: A new approach to high efficiency VRM designs

Supercapacitor assisted low dropout (SCALDO) regulator is a new approach to develop high efficiency DC-DC converters with supercapacitors used for energy recovery. One limitation in these topologies is that in some configurations a large number of low-speed switches are required. If the SCALDO technique is adapted to build voltage regulator modules (VRM), it is necessary to reduce number of switches combined with a high current capable LDO. A new topology-variation with less number of switches can be achieved by reconfiguring the original SCALDO and adding an extra LDO to the circuit. The paper presents a summary of some preliminary work, and experimental results for a 2.5V proof of concept-prototype

Morphing Switched-Capacitor Converters with Variable Conversion Ratio

High-voltage-gain and wide-input-range dc-dc converters are widely used in various electronics and industrial products such as portable devices, telecommunication, automotive, and aerospace systems. The two-stage converter is a widely adopted architecture for such applications, and it is proven to have a higher efficiency as compared with that of the single-stage converter. This paper presents a modular-cell-based morphing switched-capacitor (SC) converter for application as a front-end converter of the two-stage converter. The conversion ratio of this converter is flexible and variable and can be freely extended by increasing more SC modules. The varying conversion ratio is achieved through the morphing of the converter's structure corresponding to the amplitude of the input voltage. This converter is light and compact, and is highly efficient over a very wide range of input voltage and load conditions. Experimental work on a 25-W, 6-30-V input, 3.5-8.5-V output prototype, is performed. For a single SC module, the efficiency over the entire input voltage range is higher than 98%. Applied into the two-stage converter, the overall efficiency achievable over the entire operating range is 80% including the driver's loss

Multiport DC-DC Converters for Hybrid Energy Systems

Renewable energy sources (RESs) like solar and wind have gained attention for their potential to reduce reliance on fossil fuels and mitigate climate change. However, integrating multiple RESs into a power grid is challenging due to their unpredictable nature. Power electronic converters can manage hybrid energy systems by controlling power flow between RESs, storages, and the grid. Conventional single input dc-dc converters have limitations such as low efficiency, bulky designs, and complex control systems. Multiport dc-dc converters (MPCs) have emerged as a solution for hybridizing multiple sources, storages, and load systems by providing a common interface. Existing MPCs have limitations such as high component count, limited operational range, complex control strategies and restrictions on the number of inputs to list a few. Thus, there is a need to develop new MPCs that combine the advantages of existing designs while overcoming their limitations. Isolated MPCs with unipolar or bipolar outputs are needed that can accommodate any number of inputs, offer high voltage gain, use fixed magnetic components for galvanic isolation (regardless of the number of ports), and have a simplified control strategy. Additionally, new non-isolated MPCs with unipolar or bipolar outputs are required, featuring reduced component count, simultaneous power transfer and power flow between input ports, high voltage gain, low control complexity, and modular design allowing for arbitrary increase in the number of input ports. There is also an opportunity to apply MPCs in the integration of RESs and storages to ac grids through multilevel inverters for low component count, high efficiency, low harmonics, and higher power density. Further, advances in bipolar MPCs provide the chance to balance the dc bus without requiring a complex control system.acceptedVersio

Symmetric Multi-Level Boost Inverter with Single DC Source Using Reduced Number of Switches

In this paper a novel multilevel boost DC to DC converter with H-Bridge inverter circuit for single DC source is proposed. The proposed scheme has two stages: the first one is a multilevel boost converter which gives a multilevel dc output for a single dc source and the second level is a H-Bridge converter which converts multilevel DC to multilevel AC at required frequency. This DC-DC converter not only reduces the DC source but also reduces the switches, diodes and capacitors. This leads to decrease of the amount and the inverter space installation in order to increase the required output voltage by increasing the number of capacitors and diodes in the DC to DC converter. Comparison between the number of power switches for the suggested topology and other topologies in the recent literature is presented. Simulation results are conveyed through MatLAB/Simulink domain and the working of the suggested converter is realized

A Bidirectional Soft-Switched DAB-Based Single-Stage Three-Phase AC–DC Converter for V2G Application

In vehicle-to-grid applications, the battery charger of the electric vehicle (EV) needs to have a bidirectional power flow capability. Galvanic isolation is necessary for safety. An ac-dc bidirectional power converter with high-frequency isolation results in high power density, a key requirement for an on-board charger of an EV. Dual-active-bridge (DAB) converters are preferred in medium power and high voltage isolated dc-dc converters due to high power density and better efficiency. This paper presents a DAB-based three-phase ac-dc isolated converter with a novel modulation strategy that results in: 1) single-stage power conversion with no electrolytic capacitor, improving the reliability and power density; 2) open-loop power factor correction; 3) soft-switching of all semiconductor devices; and 4) a simple linear relationship between the control variable and the transferred active power. This paper presents a detailed analysis of the proposed operation, along with simulation results and experimental verification

Hybrid multilevel inverter using switched capacitor with boosting and self-balancing capability

Switched capacitor based multilevel inverters with boosting capability are emerging as single stage DC–AC conversion in utilizing low voltage DC sources such as solar PV and fuel cell. This paper proposes a single-phase hybrid multilevel inverter topology based on a switched capacitor that is capable of generating 9-levels along with a voltage gain of 2. The components required to construct the basic module of topology are 11 switches, 1 diode and 2 capacitors. The voltage balancing of the switched capacitors is achieved with the help of a modulation strategy, thereby eliminating the need of sensors. The theoretical loss analysis of the inverter is presented and the nearest level control based fundamental switching frequency modulation technique is employed to study the performance of the proposed inverter. The effectiveness of the suggested topology is validated with the help of a prototype built in the laboratory. The superiority of the proposed topology is assessed with the help of comparison with existing topologies

Input current shaped ac-to-dc converters

Input current shaping techniques for ac-to-dc converters were investigated. Input frequencies much higher than normal, up to 20 kHz were emphasized. Several methods of shaping the input current waveform in ac-to-dc converters were reviewed. The simplest method is the LC filter following the rectifier. The next simplest method is the resistor emulation approach in which the inductor size is determined by the converter switching frequency and not by the line input frequency. Other methods require complicated switch drive algorithms to construct the input current waveshape. For a high-frequency line input, on the order of 20 kHz, the simple LC cannot be discarded so peremptorily, since the inductor size can be compared with that for the resistor emulation method. In fact, since a dc regulator will normally be required after the filter anyway, the total component count is almost the same as for the resistor emulation method, in which the filter is effectively incorporated into the regulator

A RISC-V Vector Processor With Simultaneous-Switching Switched-Capacitor DC-DC Converters in 28 nm FDSOI

This work demonstrates a RISC-V vector microprocessor implemented in 28 nm FDSOI with fully integrated simultaneous-switching switched-capacitor DC-DC (SC DC-DC) converters and adaptive clocking that generates four on-chip voltages between 0.45 and 1 V using only 1.0 V core and 1.8 V IO voltage inputs. The converters achieve high efficiency at the system level by switching simultaneously to avoid charge-sharing losses and by using an adaptive clock to maximize performance for the resulting voltage ripple. Details about the implementation of the DC-DC switches, DC-DC controller, and adaptive clock are provided, and the sources of conversion loss are analyzed based on measured results. This system pushes the capabilities of dynamic voltage scaling by enabling fast transitions (20 ns), simple packaging (no off-chip passives), low area overhead (16%), high conversion efficiency (80%-86%), and high energy efficiency (26.2 DP GFLOPS/W) for mobile devices

A comprehensive review on Bidirectional traction converter for Electric vehicles

In this fast-changing environmental condition, the effect of fossil fuel in vehicle is a significant concern. Many sustainable sources are being studied to replace the exhausting fossil fuel in most of the countries. This paper surveys the types of electric vehicle’s energy sources and current scenario of the on-road electric vehicle and its technical challenges. It summarizes the number of state-of-the-art research progresses in bidirectional dc-dc converters and its control strategies reported in last two decades. The performance of the various topologies of bidirectional dc-dc converters is also tabulated along with their references. Hence, this work will present a clear view on the development of state-of-the-art topologies in bidirectional dc-dc converters. This review paper will be a guide for the researchers for selecting suitable bidirectional traction dc-dc converters for electric vehicle and it gives the clear picture of this research field

Two new families of high-gain DC-DC power electronic converters for DC-microgrids

Distributing the electric power in dc form is an appealing solution in many applications such as telecommunications, data centers, commercial buildings, and microgrids. A high gain dc-dc power electronic converter can be used to individually link low-voltage elements such as solar panels, fuel cells, and batteries to the dc voltage bus which is usually 400 volts. This way, it is not required to put such elements in a series string to build up their voltages. Consequently, each element can function at it optimal operating point regardless of the other elements in the system. In this dissertation, first a comparative study of dc microgrid architectures and their advantages over their ac counterparts is presented. Voltage level selection of dc distribution systems is discussed from the cost, reliability, efficiency, and safety standpoints. Next, a new family of non-isolated high-voltage-gain dc-dc power electronic converters with unidirectional power flow is introduced. This family of converters benefits from a low voltage stress across its switches. The proposed topologies are versatile as they can be utilized as single-input or double-input power converters. In either case, they draw continuous currents from their sources. Lastly, a bidirectional high-voltage-gain dc-dc power electronic converter is proposed. This converter is comprised of a bidirectional boost converter which feeds a switched-capacitor architecture. The switched-capacitor stage suggested here has several advantages over the existing approaches. For example, it benefits from a higher voltage gain while it uses less number of capacitors. The proposed converters are highly efficient and modular. The operating modes, dc voltage gain, and design procedure for each converter are discussed in details. Hardware prototypes have been developed in the lab. The results obtained from the hardware agree with those of the simulation models. --Abstract, page iv