On-chip signaling techniques for high-speed Serdes transceivers

The general goal of the VLSI technology is to produce very fast chips with very low power consumption. The technology scaling along with increasing the working frequency had been the perfect solution, which enabled the evolution of electronic devices in the 20th century. However, in deep sub-micron technologies, the on-chip power density limited the continuous increment in frequency, which led to another trend for designing higher performance chips without increasing the working speed. Parallelism was the optimum solution, and the VLSI manufacturers began the era of multi-core chips. These multi-core chips require a full inter-core network for the required communication. These on-chip links were conventionally parallel. However, due to reverse scaling in modern technologies, parallel signaling is becoming a burden due to the very large area of needed interconnects. Also, due to the very high power due to the tremendous number of repeaters, in addition to cross talk issues. As a solution, on-chip serial communication was suggested. It will solve all the previous issues, but it will require very high speed circuits to achieve the same data rates. This thesis presents two full SerDes transceiver designs for on-chip high speed serial communication. Both designs use long lossy on-chip differential interconnects with capacitive termination. The first design uses a 3-level self-timed signaling technique. This signaling technique is totally jitter-insensitive, since both of the data and clock are extracted at the receiver from the same signal. A new encoding and driving technique is designed to enable the transmitter to work at a frequency equal to the data rate, which is half of the frequency of the previous designs, along with achieving the same data rate. Also, this design generates the third voltage level without the need of an external supply. This design is very tolerant to any possible variations, such as PVT variations or the input clock\u27s duty cycle variations. This transceiver is prepared for tape-out in UMC 0.13μm CMOS technology in June 2014. The second design uses a new 3-level signaling technique; the proposed technique uses a frequency of only half the data rate, which totally relaxes the full transceiver design. The new technique is also self-timed enabling the extraction of both the data, and the clock from the same signal. New encoders and decoders are designed, and a new architecture for a 3-level inverter is presented. This transceiver achieves very high data rates. This new design is expected to be taped-out using the GF 65nm CMOS technology in August 2014

Analog/RF Circuit Design Techniques for Nanometerscale IC Technologies

CMOS evolution introduces several problems in analog design. Gate-leakage mismatch exceeds conventional matching tolerances requiring active cancellation techniques or alternative architectures. One strategy to deal with the use of lower supply voltages is to operate critical parts at higher supply voltages, by exploiting combinations of thin- and thick-oxide transistors. Alternatively, low voltage circuit techniques are successfully developed. In order to benefit from nanometer scale CMOS technology, more functionality is shifted to the digital domain, including parts of the RF circuits. At the same time, analog control for digital and digital control for analog emerges to deal with current and upcoming imperfections

Exploration and Design of High Performance Variation Tolerant On-Chip Interconnects

Siirretty Doriast

High-Speed and Low-Energy On-Chip Communication Circuits.

Continuous technology scaling sharply reduces transistor delays, while fixed-length global wire delays have increased due to less wiring pitch with higher resistance and coupling capacitance. Due to this ever growing gap, long on-chip interconnects pose well-known latency, bandwidth, and energy challenges to high-performance VLSI systems. Repeaters effectively mitigate wire RC effects but do little to improve their energy costs. Moreover, the increased complexity and high level of integration requires higher wire densities, worsening crosstalk noise and power consumption of conventionally repeated interconnects. Such increasing concerns in global on-chip wires motivate circuits to improve wire performance and energy while reducing the number of repeaters. This work presents circuit techniques and investigation for high-performance and energy-efficient on-chip communication in the aspects of encoding, data compression, self-timed current injection, signal pre-emphasis, low-swing signaling, and technology mapping. The improved bus designs also consider the constraints of robust operation and performance/energy gains across process corners and design space. Measurement results from 5mm links on 65nm and 90nm prototype chips validate 2.5-3X improvement in energy-delay product.Ph.D.Electrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/75800/1/jseo_1.pd

An Energy-Efficient Reconfigurable Mobile Memory Interface for Computing Systems

The critical need for higher power efficiency and bandwidth transceiver design has significantly increased as mobile devices, such as smart phones, laptops, tablets, and ultra-portable personal digital assistants continue to be constructed using heterogeneous intellectual properties such as central processing units (CPUs), graphics processing units (GPUs), digital signal processors, dynamic random-access memories (DRAMs), sensors, and graphics/image processing units and to have enhanced graphic computing and video processing capabilities. However, the current mobile interface technologies which support CPU to memory communication (e.g. baseband-only signaling) have critical limitations, particularly super-linear energy consumption, limited bandwidth, and non-reconfigurable data access. As a consequence, there is a critical need to improve both energy efficiency and bandwidth for future mobile devices.;The primary goal of this study is to design an energy-efficient reconfigurable mobile memory interface for mobile computing systems in order to dramatically enhance the circuit and system bandwidth and power efficiency. The proposed energy efficient mobile memory interface which utilizes an advanced base-band (BB) signaling and a RF-band signaling is capable of simultaneous bi-directional communication and reconfigurable data access. It also increases power efficiency and bandwidth between mobile CPUs and memory subsystems on a single-ended shared transmission line. Moreover, due to multiple data communication on a single-ended shared transmission line, the number of transmission lines between mobile CPU and memories is considerably reduced, resulting in significant technological innovations, (e.g. more compact devices and low cost packaging to mobile communication interface) and establishing the principles and feasibility of technologies for future mobile system applications. The operation and performance of the proposed transceiver are analyzed and its circuit implementation is discussed in details. A chip prototype of the transceiver was implemented in a 65nm CMOS process technology. In the measurement, the transceiver exhibits higher aggregate data throughput and better energy efficiency compared to prior works

High-Speed Low-Voltage Line Driver for SerDes Applications

The driving factor behind this research was to design & develop a line driver capable of meeting the demanding specifications of the next generation of SerDes devices. In this thesis various line driver topologies were analysed to identify a topology suited for a high-speed low-voltage operating environment. This thesis starts of by introducing a relatively new high-speed communication Device called SerDes. SerDes is used in wired chip-to-chip communications and operates by converting a parallel data stream in a serial data stream that can be then transmitted at a higher bit rate, existing SerDes devices operate up to 12.5Gbps. A matching SerDes device at the destination will then convert the serial data stream back into a parallel data stream to be read by the destination ASIC. SerDes typically uses a line driver with a differential output. Using a differential line driver increases the resilience to outside sources of noise and reduces the amount of EM radiation produced by transmission. The focus of this research is to design and develop a line driver that can operate at 40Gbps and can function with a power supply of less than IV. This demanding specification was decided to be an accurate representation of future requirements that a line driver in a SerDes device will have to conform to. A suitable line driver with a differential output was identified to meet the demanding specifications and was modified so that it can perfonn an equalisation technique called pre-distortion. Two variations of the new topology were outlined and a behavioural model was created for both using Matlab Simulink. The behavioural model for both variants proved the concept, however only one variant maintained its perfomance once the designs were implemented at transistor level in Cadence, using a 65nm CMOS technology provided by Texas Instruments. The final line driver design was then converted into a layout design, again using Cadence, and RC parasitics were extracted to perfom a post-layout simulation. The post layout simulation shows that the novel line driver can operate at 40Gbps with a power supply of 1 V - O.8V and has a power consumption of 4.54m W /Gbps. The Deterministic Jitter added by the line driver is 12.9ps

Doctor of Philosophy

dissertationCommunication surpasses computation as the power and performance bottleneck in forthcoming exascale processors. Scaling has made transistors cheap, but on-chip wires have grown more expensive, both in terms of latency as well as energy. Therefore, the need for low energy, high performance interconnects is highly pronounced, especially for long distance communication. In this work, we examine two aspects of the global signaling problem. The first part of the thesis focuses on a high bandwidth asynchronous signaling protocol for long distance communication. Asynchrony among intellectual property (IP) cores on a chip has become necessary in a System on Chip (SoC) environment. Traditional asynchronous handshaking protocol suffers from loss of throughput due to the added latency of sending the acknowledge signal back to the sender. We demonstrate a method that supports end-to-end communication across links with arbitrarily large latency, without limiting the bandwidth, so long as line variation can be reliably controlled. We also evaluate the energy and latency improvements as a result of the design choices made available by this protocol. The use of transmission lines as a physical interconnect medium shows promise for deep submicron technologies. In our evaluations, we notice a lower energy footprint, as well as vastly reduced wire latency for transmission line interconnects. We approach this problem from two sides. Using field solvers, we investigate the physical design choices to determine the optimal way to implement these lines for a given back-end-of-line (BEOL) stack. We also approach the problem from a system designer's viewpoint, looking at ways to optimize the lines for different performance targets. This work analyzes the advantages and pitfalls of implementing asynchronous channel protocols for communication over long distances. Finally, the innovations resulting from this work are applied to a network-on-chip design example and the resulting power-performance benefits are reported

Driving the Network-on-Chip Revolution to Remove the Interconnect Bottleneck in Nanoscale Multi-Processor Systems-on-Chip

The sustained demand for faster, more powerful chips has been met by the availability of chip manufacturing processes allowing for the integration of increasing numbers of computation units onto a single die. The resulting outcome, especially in the embedded domain, has often been called SYSTEM-ON-CHIP (SoC) or MULTI-PROCESSOR SYSTEM-ON-CHIP (MP-SoC). MPSoC design brings to the foreground a large number of challenges, one of the most prominent of which is the design of the chip interconnection. With a number of on-chip blocks presently ranging in the tens, and quickly approaching the hundreds, the novel issue of how to best provide on-chip communication resources is clearly felt. NETWORKS-ON-CHIPS (NoCs) are the most comprehensive and scalable answer to this design concern. By bringing large-scale networking concepts to the on-chip domain, they guarantee a structured answer to present and future communication requirements. The point-to-point connection and packet switching paradigms they involve are also of great help in minimizing wiring overhead and physical routing issues. However, as with any technology of recent inception, NoC design is still an evolving discipline. Several main areas of interest require deep investigation for NoCs to become viable solutions: • The design of the NoC architecture needs to strike the best tradeoff among performance, features and the tight area and power constraints of the onchip domain. • Simulation and verification infrastructure must be put in place to explore, validate and optimize the NoC performance. • NoCs offer a huge design space, thanks to their extreme customizability in terms of topology and architectural parameters. Design tools are needed to prune this space and pick the best solutions. • Even more so given their global, distributed nature, it is essential to evaluate the physical implementation of NoCs to evaluate their suitability for next-generation designs and their area and power costs. This dissertation performs a design space exploration of network-on-chip architectures, in order to point-out the trade-offs associated with the design of each individual network building blocks and with the design of network topology overall. The design space exploration is preceded by a comparative analysis of state-of-the-art interconnect fabrics with themselves and with early networkon- chip prototypes. The ultimate objective is to point out the key advantages that NoC realizations provide with respect to state-of-the-art communication infrastructures and to point out the challenges that lie ahead in order to make this new interconnect technology come true. Among these latter, technologyrelated challenges are emerging that call for dedicated design techniques at all levels of the design hierarchy. In particular, leakage power dissipation, containment of process variations and of their effects. The achievement of the above objectives was enabled by means of a NoC simulation environment for cycleaccurate modelling and simulation and by means of a back-end facility for the study of NoC physical implementation effects. Overall, all the results provided by this work have been validated on actual silicon layout

Modeling of Photonic Devices and Photonic Integrated Circuits for Optical Interconnect and RF Photonic Front-End Applications

Photonic integrated circuits (PICs) offer compelling solutions for applications in many areas due to the sufficient functionality and excellent performance. Optical interconnects and radio frequency (RF) photonics are two areas in which PICs have potential to be widely used. Optical interconnect system efficiency is dependent on the ability to optimize the transceiver circuitry for low-power and high-bandwidth operation, motivating co-simulation environments with compact optical device simulation models. Compact models for vertical-cavity surface-emitting lasers (VCSELs) and silicon carrier-injection/depletion ring modulators which include both non-linear electrical and optical dynamics are presented, and excellent matching between co-simulated and measured optical eye diagrams is achieved. Advanced modulation schemes, such as four-level pulse-amplitude modulation (PAM4), are currently under consideration in both high-speed electrical and optical interconnect systems. How NRZ and PAM4 modulation impacts the energy efficiency of an optical link architecture based on silicon photonic microring resonator modulators and drop filters is analyzed. Two ring modulator device structures are proposed for PAM4 modulation, including a single-segment device driven with a multi-level PAM4 transmitter and a two-segment device driven by two simple NRZ (MSB/LSB) transmitters. Modeling results show that the PAM4 architectures achieve superior energy efficiency at higher data rates due to the relaxed circuit bandwidth. While RF photonics offer the promise of chip-scale opto-electrical systems with high levels of functionality, in order to avoid long and unsuccessful design cycles, efficient models that allow for co-simulation are necessary. In order to address this, an optical element modeling framework is proposed based on Verilog-A which allows for the co-simulation of optical elements with transistor-level circuits in a Cadence design environment. Three components in the RF photonic system, Mach Zehnder (MZ) modulators, 4th order all pass filter (APF)-based optical filters, and jammer-suppression notch filters are presented to demonstrate the capability of efficient system design in co-simulation environments